Find your next part.

Two-piece platform for mounting an Apple MagSafe USB-C adapter in the 12 V smoker-package compartment below the shifter. The creator calls for a low-profile USB-C 12 V car adapter, automotive trim tape, and glue or epoxy for PLA.

Fits Macan · 95B

Round push-in cover for an interior-trim screw opening, with the opening enlarged by the creator for the larger screws used in their installation.

Fits 944 · 944

Temporary plate that bolts over the cylinder-head intake-manifold mounting face to keep debris out during engine assembly.

Fits 914 · 914

Push-on replacement caps for the screws that retain the fender; the archive supplies standard and rounded variants.

Fits 924 · 924 · 944 · 944

Replacement front speaker grille for late-model 944 cars, modeled around Tref67's speaker spacer after the creator found both pieces missing.

Fits 944 · 944

Replacement plastic clip for securing the regulator/relay-board wiring harness. The creator modeled it from the unavailable original, specifies ABS, and shows the original beside the printed replacement.

Fits 914 · 914

Two-piece offset front license-plate mount comprising a curved plate bracket and screw-in tow-eye adapter. The adapter is bored for through-bolt reinforcement; the creator describes the shorter adapter as 78 mm long and suggests an approximately 85 mm M10 bolt.

Fits 911 · 997 · Boxster · 986

Protective installation cap that covers crankcase through-bolt threads so an O-ring is not sliced while being installed. The creator designed it during a 914-6/911T engine rebuild and revised the shape for improved printing.

Fits 911 · Original (901/911) · 914 · 914

Replacement end cap, catalogued as a sleeve, for the 914-6 manual-throttle rod. The creator recreated it from broken pieces of the original part and old-stock photographs.

Fits 914 · 914

Replacement set for the heater-panel slider levers, supplied as separate upper and lower STL models.

Fits 924 · 924

Cup holder with a 4-inch opening designed to fit the change-holder location; the creator contrasts it with an original 3-inch-opening version.

Fits Boxster · 986

Clamp that adapts the creator-linked Amazon phone holder to mount on the side of the center console instead of an air vent.

Fits Taycan · J1

Flexible clip-on spacer with increased retention for the thinner lower arm of a twin-arm rear wiper, keeping the paired metal arms from clacking together.

Fits 928 · 928

Replacement shaft for the instrument-cluster trip and dimmer controls, measured from an OEM stalk. The creator recommends resin or ABS for resolution and heat resistance and notes that sanding may be needed for a close fit.

Fits 911 · 996 · Boxster · 986

Ashtray-mounted phone stand with a USB cable pass-through for an adhesive magnetic charging puck, designed by Trogdor4Ever for the Cayenne 958 center console. The creator printed it in PLA+ and added neoprene foam to the lower corners for a snugger fit.

Fits Cayenne · E2 (958)

Printable lining for a center-console-delete conversion, supplied as a full model or front/rear split for a Prusa Mk3S-size bed, plus a cover plate. The creator recommends PETG, instructs removal of the orange bracket tabs for mounting, and leaves room to upholster the part.

Fits Boxster · 986

Center-console phone mount based on the creator's 3D scan, with versions for iSetchi and Apple MagSafe chargers. The creator reports months of in-car use and says the Apple charger must be attached with double-sided tape or glue.

Fits Taycan · J1

Three-part clip-in center-console coin tray that replaces the ashtray. The creator directs users to slide the parts together, glue the seams, and apply fabric tape at the sides to improve fit and reduce rattles.

Fits 944 · 944

Clip-in dual cup holder replacing the centre-console ashtray, with multiple drink-size adapters, a watertight compartment and a flexible anti-rattle mat.

Fits 944 · 944

One-piece phone-holder mount for the stock stereo with an approximately 17 mm ball. The creator says it worked with an existing holder and used foam tape beneath the ball to reduce bounce.

Fits Boxster · 986

Vent-wall clamp with an integrated one-inch ball for accessory or phone-mount arms. It expands against the vent walls with two M5 x 18 mm tensioning screws and uses 1/16-inch rubber sheet for grip and trim protection.

Fits Panamera · G1 (970)

Cap for unused headlight-washer openings in Turbo and S2-style front bumpers.

Fits 944 · 944

Plastic clip that holds the fuel rail to the engine-bay firewall, modeled against an original clip.

Fits 914 · 914

Two-piece bracket that mounts a remote clutch bleed-screw assembly to the fan shroud. It is sized for a -3 AN bulkhead mount accepting a 3/8-24 bleeder screw and uses a removable end plate so the clutch line can be slid into place without disconnecting it.

Fits 911 · 993