Find your next part.

Remix of RomainCNC's magnetic phone-holder base for the central console, adding a ball for swivel holders. V1 has a 16 mm ball and V2 a 16.5 mm ball. The creator specifies ABS because PLA can deform in a sun-heated car.

Fits MiTo · Tipo 955

Adapter at the interior-mirror location for a Sony Xperia Z5 Compact phone, as identified by the creator.

Fits Giulia · Tipo 952

Replacement retaining clip for the front fog lamp. The creator identifies fitment to the 75/Milano, states the clips are no longer made, and recommends at least PETG.

Fits 75 · Tipo 162B / 161

Replacement headlamp-washer jet nozzles for the 155, created because the originals deteriorate in sunlight. The source supplies the standard nozzle and a spray variant.

Fits 155 · Tipo 167

Redesigned support for the bonnet prop rod. The creator reports that the earlier PLA version lasted more than two years, recommends PETG or another heat-resistant material, 40% infill and supports, and added a screw to retain the rod when the support yields.

Fits 145 / 146 · 145 / 146 (Tipo 930)

Replacement clip for the sunroof mechanism. The creator reports a successful test on one car and specifies PLA, a 0.8 mm nozzle, and 100% infill.

Fits GTV · Alfetta GT / GTV / GTV6 (Tipo 116)

Two solid filler blocks for the jack-point air gaps. The creator printed them at 100% infill in ABS as a lower-cost alternative to 0.25-inch and 0.125-inch ABS or Delrin sheet.

Fits 4C · Tipo 960

It fits in front of the ignition-switch, designed for the eezee power switch panel so it has a mounting surface of 68x115 mm and mirrored version for RHD vehicles

Fits Range Rover · L322

Left and right replacement hinges for the rear parcel shelf. The original source supplies both handed files and a physical comparison image; a later credited remix explicitly identifies this original design as the W177 parcel-shelf hinge and retains the same interface while adding reinforcement. Print the original files on their flat sides at 0.16 mm, with four walls and no supports; the creator suggests fuzzy skin only on the four towers that enter the parcel shelf. A later source specifies PETG for this cabin/cargo application. Inspect layer adhesion and both pivots, confirm free movement, and avoid loading the shelf until both hinges are fully seated. No Mercedes number is assigned: A1776905400 identifies the complete parcel shelf, not either printed hinge child.

Fits A-Class · W177

Three-piece organizer and lid system for the center-console storage compartment. The preserved author package names the main organizer and lid geometry for W177, and four author photographs show the parts installed and in use. No screws or bolts are required; the creator states that the hooks lock into place with light force. Use a cabin-heat-resistant material, test the hook engagement gradually, and verify that the lid and armrest open and close freely without pinching stored items or wiring.

Fits A-Class · W177

Drop-in holder for a MagSafe-compatible wireless charger in the front storage cubby. The creator made and photographed it in a 2020 car and explicitly states W177 fitment. They also suggest same-generation W247, C118, H247 and X247 compatibility but require a visual cubby check; those lines are not among the live generations in this catalog, so only the tested W177 generation is linked. The model is sized around the charger identified on the source page and was designed for an S23 Ultra; verify phone, case, charger and cable clearance before printing. Place the largest face down and use supports. The creator recommends a cabin-heat-resistant material such as PET, PETG, ABS or ASA. Secure the cable and confirm the dock cannot obstruct controls or become loose while driving.

Fits A-Class · W177

Working replacement trim plug for the rear-seat ISOFIX anchor opening, derived by the creator from a 3D scan of the factory cover. The creator states that the scan is not perfect; compare the upholstery opening and verify secure seating. This is only a removable trim cap: it must not obstruct, modify or carry load from the ISOFIX anchor, and it should be removed before attaching a child restraint.

Fits E-Class · W213 / S213 / C238 / A238

Replacement hinge for the under-carpet luggage-compartment floor panel in the source-stated estate body. Mirror the supplied model in the slicer for the opposite side. The creator recommends ABS, ASA or PETG, supports, four walls, five top and bottom layers and 50% infill, and updated the geometry to improve fit and avoid cracking caused by tight tolerances. Confirm free closing movement and screw-slot adjustment before loading the panel. Creator-stated A2136846900 was researched but is not assigned because official listings identify that number as a cover rail rather than this printed hinge child.

Fits E-Class · W213 / S213 / C238 / A238

Two alternative bases for attaching an aftermarket ball-joint phone holder between the circular dashboard vents. The creator explicitly designed the geometry for the 213/238-series E-Class vent arrangement and shows the adhesive version installed. The second version is intended to engage the vent slots without adhesive, but the creator states that this version was not tested and warns against PLA because it may break during installation. Use a cabin-heat-resistant material, verify adhesive or clip retention before driving, and keep the device clear of controls, airbags and the driver's view.

Fits E-Class · W213 / S213 / C238 / A238

Two-piece mount designed for a 2018 GLC and a 12.9-inch sixth-generation iPad Pro. The vehicle-side piece slips over the factory display and accepts a soft-opening hinge so the tablet can be moved for rear-camera use. Source imagery is CAD/render evidence only. Verify the exact tablet and hinge hardware, protect the factory screen and trim, secure and strain-relieve all wiring, preserve visibility of the road, instruments and reversing image, and remove the mount if it loosens, obstructs controls, or overheats.

Fits GLK / GLC · X253 / C253

Cupholder-mounted phone cradle designed for a GLC 300 and sized for a Samsung Galaxy A51 in a folding case. Openings in the body are intended to improve phone-audio output. Fit depends on the stated phone and case envelope; verify the cradle seats fully, retains the phone during driving, remains clear of the selector and controls, and does not soften or crack in cabin heat.

Fits GLK / GLC · X253 / C253

Two drop-in console inserts created and physically test-fitted in a GLC: one plain storage cup and one version with a shopping-cart coin slot. The source shows the factory console both open with the inserts fitted and closed over them. Use a cabin-heat-resistant material, confirm the selected insert seats without stressing the factory cupholder, keep loose contents away from controls, and stop use if the print softens, cracks, or binds the console cover.

Fits GLK / GLC · X253 / C253

Insert replacing the Peiker phone-preparation module position between the 12 V socket and original USB/MMI panel in the centre console. The creator verified it on a V-Class with that exact console layout and warns that other Vito variants must be compared by photographs and the stated 72 × 129 × 12 mm dimensions. Use ASA as recommended, or ABS; PETG is only cautiously suggested and PLA is excluded. Fit a dimensionally compatible MagSafe/Qi charger, use an automotive DC-DC/USB-C module with a dedicated fuse, mechanically secure and insulate every wire, check charging heat under extended use, and confirm the assembly cannot interfere with controls. Electrical installation remains at the installer’s risk.

Fits Vito / Viano / V-Class · W447

Replacement clip joining a Rituals fragrance dispenser to the centre ventilation slats in a 2025 facelift V-Class. The creator printed and physically shows it installed, specifies PETG with 0.2 mm layers and 30% infill, and deliberately strengthened the design. Fitment is limited to the facelift centre vent and the matching Rituals dispenser back bars. Confirm both interfaces, insert without bending or scratching the vent slats, preserve airflow and vent adjustment, and remove the accessory if it loosens or obstructs controls or visibility.

Fits Vito / Viano / V-Class · W447

Cupholder-mounted charging dock remixed specifically for the 2014–2022 Vito and tested with an iPhone 12 Pro Max in a thin Pitaka Air case; the creator also states iPhone 13 Pro Max fitment. It requires a small Lightning plug such as the cited 0.5 m Apple cable, with tape used to make the plug snug, and includes a cable channel to the nearby USB port. Print in PETG as recommended, match the exact phone/case/plug and cupholder, secure and route the cable safely, and verify the dock cannot obstruct controls or release the phone under braking.

Fits Vito / Viano / V-Class · W447

Charging dock shaped for the front centre-console cupholder and an iPhone 12 in an Elago silicone case. The creator states exact Vito fitment, recommends ABS or PETG because cabin temperatures can exceed 70 °C, and notes that other cases, phones and cable plugs require geometry changes. Match the cupholder, phone case and charging connector, route the cable without pinching it, use supports as specified, and verify the dock and phone stay retained without obstructing the selector or controls.

Fits Vito / Viano / V-Class · W447

Cosmetic plug for closing the exposed holes left after removing the armrests from individual V-Class seats. The creator explicitly tags this chassis and supplies the printable child geometry and multiple CAD source views, but gives no material, seat-version, colour or long-term retention details. PETG, ABS and nylon are listed only as conservative tough cabin-heat-resistant choices. Compare the exposed seat hole and plug profile, fit without forcing the seat trim, and confirm the plug remains secure and does not interfere with seat adjustment or restraint hardware.

Fits Vito / Viano / V-Class · W447

Two-piece holder that slides over the central Audio 20 display and carries a 12.9-inch second-generation iPad Pro in its leather case. The creator explicitly designed it for the V-Class/Vito/Marco Polo display in this chassis and instructs bonding the two printed pieces after printing. The source gives no material; PETG, ABS and nylon are listed only as conservative cabin-heat-resistant choices. Match the Audio 20 display and tablet/case dimensions, line the vehicle-display interface with textile tape as shown on the same-author follow-up, and verify the holder cannot obscure the road, controls or airbags or release the tablet under braking.

Fits Vito / Viano / V-Class · W447

Two-level center-armrest organizer source-backed for 2015–2021 C-Class interiors and the corresponding GLC console. The upper tray includes Canadian coin slots, a phone compartment and general storage; the lower tray catches loose items. Source imagery is CAD and slicer evidence only. Verify the 258×123×65 mm envelope before printing, ensure the lid closes freely, and do not place items where they can jam the console or controls.

Fits C-Class · W205 / S205 / C205 / A205 · GLK / GLC · X253 / C253