Find your next part.

Two-piece dashboard navigation-device holder for the Nissan NV200 M20. The holder seats in the opening on top of the dashboard, supports a TomTom Go5200 or compatible suction-cup device up to 60 mm, routes the power cable through provided openings, and is retained with double-sided tape. Includes the main holder and top cover; tape, navigation device, and other hardware are separate. PETG or ASA is recommended for cabin heat exposure.

Fits Nissan NV200 · M20

Replacement translucent insert for the broken internal section of a manual/standard heater-control knob. Fits the standard heater-control panel represented by the 2003 application within Nissan X-Trail T30 generation 2903; it is not intended for climate-control panels. The insert restores the knob shaft interface and light-transmitting inner piece. Clean and fit carefully: the documented test fit did not seat fully, and forcing the insert can damage the shaft.

Fits X-Trail · T30

Full-size distributor-cap block-off cover for the Nissan Z31 (1983–1989) engine bay after conversion from distributor ignition to coil packs. The cover closes the distributor-cap opening and includes an integrated recessed Z emblem; the printed component and its mounting features are modeled, while installation hardware and the vehicle are not included. Print in PETG, ABS, or another heat-suitable material and verify fastener engagement, sealing, and engine-bay clearances before use.

Fits Fairlady Z / Nissan Z · Z31

Full-size passenger-side front brake vent for the EUDM/AUSDM Nissan 300ZX Z31. The vented grille directs airflow through four openings toward the front brake area and mounts in the side bodywork ahead of the wheel. The supplied geometry represents the right-hand part; mirror it for the driver side. Verify body-opening dimensions, mounting tabs, side orientation, and brake-clearance before installation.

Fits Fairlady Z / Nissan Z · Z31

Full-size replacement pod for the dashboard vent opening, mounting below the dash and accepting either a 52 mm or 60 mm gauge. The packet includes the standard base, mirrored base, 52 mm insert, and 60 mm V2 insert; two M4x30 bolts and two M4 nuts are required separately. The design is intended as a reversible replacement without cutting or drilling. PETG or ABS are engineering-inferred for cabin heat resistance; verify gauge fit, retention, clearances, and print strength before driving.

Fits Nissan 180SX · RS13/RPS13 · Nissan Silvia · S13

Full-size radiator support mounting bracket for Nissan Silvia S13 and 180SX RS13/RPS13 applications, with the source also identifying 200SX and 240SX market variants. The bracket mounts at the front radiator support and retains the radiator with the corresponding vehicle hardware. Includes one printed bracket; verify exact market/body variant, hole spacing, fasteners, clearances, and engine-bay heat and vibration suitability before installation.

Fits Nissan 180SX · RS13/RPS13 · Nissan Silvia · S13

Four-piece set of replacement holders for routing and retaining underbody fuel lines on Nissan 180SX RS13/RPS13 and Nissan Silvia S13 applications. The selected OEM-replacement variant includes Halter 1 E, Halter 2 E, Halter 3 E, and Halter 4 E; print duplicates as needed for the vehicle's layout. This variant retains the fuel lines and the original evap/fuel-tank venting line. Verify line routing, fastener fit, clearance, and print strength on the specific vehicle before installation.

Fits Nissan 180SX · RS13/RPS13 · Nissan Silvia · S13

Full-size replacement clips for the radio-console/bezel mounting interface. The set includes single-clip and multi-pack variants for Nissan 180SX RS13/RPS13 and Silvia S13 applications represented by the selected catalog generations; the clips restore retention of the radio-console bezel when original clips are missing or broken. PETG is recommended for vehicle-cabin use, while ABS was used for the earlier prints.

Fits Nissan 180SX · RS13/RPS13 · Nissan Silvia · S13

Organizer tray for the small front console tray ahead of the shift lever in 2014–2020 second-generation Rogue vehicles. It fits over the rubber tray liner, preserves access to the lighter/power socket and USB-A port, and adds storage sections, pen slots, and a coin slot. Supports are required; PETG or another heat-resistant material is recommended for vehicle-cabin temperatures.

Fits X-Trail / Rogue · T32

Left- and right-side replacement support clips for the rear parcel shelf (boot privacy cover). The clips slot into the existing side recesses and support the cover, restoring its resting support on 2002–2010 Nissan March K12 / Micra K12 hatchbacks. Print in PETG for hot-car resistance; PLA is not suitable for this application.

Fits March · K12

Two-component replacement set for the rear quarter-window regulator mechanism on the 2006 convertible application represented by Nissan March K12 generation 2767. The set includes the main mechanism component and an outside component intended to restore rear-window extension operation; verify side, mating interfaces, dimensions, hardware, clearances, and print-material suitability before installation.

Fits March · K12

Replacement battery hold-down bracket for the 1969-1978 Fairlady Z / Datsun Z S30 application represented by 240Z, 260Z, and Fairlady Z fitments. It uses the stock firewall bolt hole and standard battery-tray tie-down rod to secure a smaller or lower battery. Includes one printed bracket; the battery, tie-down rod, fasteners, and tray are not included. Creator guidance specifies Nylon and notes that PETG or another higher-temperature filament may also be suitable for engine-bay temperatures; supports are required for the long battery-contact area.

Fits Fairlady Z / Datsun Z · S30

3D-printable holder for a Samsung Galaxy Note 9. The printed rail mounts between the radio and dashboard/vent area and supports the phone in front of the center vents. Verified fitment covers 2012-2016 Impreza and 2013-2017 Crosstrek vehicles. The printed holder is the modeled component; the phone and any non-printed mounting hardware are not included.

Fits Impreza · Fourth generation (GJ/GP) · XV / Crosstrek · First generation (GP)

Clip-on dashboard vent mount for a Garmin GPS/navigation unit in the center vents of the 2015 Subaru Outback (fifth generation, BS). The flexible clip straddles the emergency-flasher button area while preserving access to the vents and can be moved between the two center vents; the updated version has reduced pivot range compared with the original clip and is intended to print vertically with tree supports. The vehicle and GPS device are not included.

Fits Outback · Fifth generation (BS)

Full-size cup holder for the dashboard ashtray/blanking-panel opening on a 1997 Subaru Sambar KS4. It provides a 66 mm opening for cans and, with the removable filler washer removed, approximately 71 mm clearance for larger cups or bottles while clearing the manual gear lever. The model includes the cup-holder body and removable filler washer; confirm the dash opening, shift-lever clearance, retention, and print strength before installation.

Fits Sambar · Fifth generation (KS3/KS4/KV3/KV4)

Full-size adapter for mounting an HKS SQV 4 blow-off valve to the factory recirculation plumbing, returning discharged air to the intake system. Verified fitment is the fourth-generation Subaru Legacy BL/BP (2003-2009) with the compatible valve and flange arrangement. Intended for engine-bay service; print in ABS, ASA, or PA-6 CF and verify gasket seating, hose routing, clamp retention, and clearances before operation.

Fits Legacy · Fourth generation (BL/BP)

Three-gauge dashboard mount for the center dash lid of the 2009 Forester. The mount provides three instrument-gauge openings, uses a drilling template to locate the mounting holes, and attaches with four M4 screws. The selected files include the current pod body and the drilling-template component; gauge diameter and hardware supply were not verified.

Fits Forester · Third generation (SH)

Two alternative full-size phone-mount variants for the center-console coin pocket of the 2018 Subaru Outback fifth generation (BS). One variant uses a 1.25-inch slot interface and the other provides a flat face for an adhesive-backed mount. Printed parts only; phone, adhesive mount, and mounting hardware are not included. Verify pocket interface, device clearance, retention, cable routing, and unobstructed visibility before driving.

Fits Outback · Fifth generation (BS)

Replacement lower instrument-panel cover that fills the factory switch/blanking-panel opening and restores the retaining features of the original cover. Verified fitment is the first-generation Subaru Impreza GC/GF/GM and first-generation Forester SF, corresponding to OEM 66813FA000; verify the dashboard variant and retention before installation.

Fits Forester · First generation (SF) · Impreza · First generation (GC/GF/GM)

Hanging two-way-radio mount with an integrated cup holder that attaches to the passenger-side centre storage area of the BT Outback without drilling or modifying the vehicle. The multipart kit includes the main body, two hangers, and a paired support component; it is sized for a small 100 mm × 25 mm GMC radio, and the included geometry supports resizing for other small radios.

Fits Outback · Sixth generation (BT)

Full-size printed phone holder designed for 2015–2021 WRX/STI interiors and sized by the creator for a large phone in a heavy case. The single-piece design provides the phone-supporting geometry; PETG or ABS is specified for in-car heat and supports are required for printing.

Fits WRX · First generation (VA)

Vented rear cap for the headlight housing on 2006-2008 Subaru Forester SG facelift applications. It provides extended clearance for H1-size aftermarket LED low-beam bulbs with rear cooling fans, vented louvers for airflow, and an external wire slot for the voltage-box lead. The same cap fits both sides; reuse the stock O-ring and print a pair. Full waterproofing is not guaranteed, so verify bulb tail depth, cap-tab engagement, clearances, and sealing before installation. Print in ASA or another heat- and UV-resistant automotive material.

Fits Forester · Second generation (SG)

Four-piece flush-mount auxiliary-light housing and retainer kit for the front bumper fog-light openings of 2006–2008 Forester Sports (SG facelift) vehicles. The kit comprises left and right housings plus left and right retainers, accepts a compatible small pod using a single through-bolt bracket, and allows vertical and horizontal beam aiming. Includes the printed housings and retainers; light pods, relay, switch, connectors, heat-set inserts, and fasteners are separate. Verify pod dimensions, wiring, clearances, weather sealing, print strength, and local lighting regulations before installation.

Fits Forester · Second generation (SG)

Square-to-round cup holder insert for a front center-console cup well. The single printed component drops into a square opening and provides a cylindrical recess that stabilizes a round beverage container; duplicate the insert for a paired set of front wells when needed. Verified fitment is the third-generation SH application represented by generation 1215 (2008-2012). Use ABS or another heat-resistant material and verify retention, cup clearance, and unobstructed access before driving.

Fits Forester · Third generation (SH)