Find your next part.

Phone holder made for a Samsung Galaxy Note 4 and shown physically installed across the centre dashboard vents. Confirm the phone dimensions, vent geometry, hazard/control access and sight lines before use. Print in cabin-heat-resistant material, deburr all contact surfaces, avoid loading fragile vent vanes and verify the phone cannot detach, obscure the road or interfere with controls or airbags under braking.

Fits C-Class · W202 / S202

Cup holder for a cassette-deck opening, tested by the creator in this vehicle generation with 12 oz and 16 oz UK cups. Two OBJ variants are supplied: zero degrees and 25 degrees; the creator states the 25-degree version keeps a drink upright in this cabin. The stereo must remain in cassette-eject mode while fitted. Use cabin-heat-resistant material, verify the deck supports the holder without damage, keep liquids away from electrical controls and occupants, and test retention with a cold, closed container before road use; hot liquids and abrupt braking can cause burns or electronic damage.

Fits C-Class · W202 / S202

Front-door speaker adapter for shallow 160–170 mm drivers; the creator used a 50 mm-deep Pioneer driver. The supplied geometry is for the right/passenger side and must be mirrored for the left/driver side. The source specifies no supports, 0.3 mm layers, 0.8 mm walls and 30% infill, and requires drilling a small wire hole and sealing it after routing. Match the speaker basket and door mounting pattern, use cabin-heat- and vibration-resistant material, protect wiring, seal the wire opening and confirm both adapter and driver remain secure without interfering with glass or trim.

Fits C-Class · W202 / S202

Original-style and gusset-reinforced replacement variants for the sprung latch inside the center-armrest storage cubby, with creator-stated fitment for 1992–1999 vehicles. The creator also states that mirroring the geometry makes it work for the glove-box latch in the same generation. The source photograph shows the physical latch mechanism and child piece. Independent inspection found the gusseted STL non-watertight, so repair and validate that mesh before slicing. The author reports that commissioned ABS versions lasted about 18 months despite embedded steel wire and changed to SLM 316L stainless steel for expected long-term durability. If printing in polymer, use a tough cabin-heat-resistant material, keep a spare, and verify reliable spring engagement and positive latching before use. Work over a clean surface to avoid losing the original spring; a replacement spring may require a carefully filed groove in the post.

Fits S-Class · W140 / C140

Four-piece left/right replacement retainer set for the power-seat switch panels, explicitly designed as a direct replacement for a 1990s S420. The source photographs show the physical panel assemblies and installed retainers. Independent mesh inspection found three of the four preserved STLs non-watertight, so repair and validate the sliced geometry before printing. Compare side and switch-panel version before use, print in a tough cabin-heat-resistant material, retain the original fasteners, and verify that the panel is secure without restricting any seat control or trapping wiring.

Fits S-Class · W140 / C140

Speaker adapter developed and used to install a Polk DB652 in a 2002 G500. The preserved author file is named as a rear speaker mount; the source states that the adapter bolts to the vehicle with the original hardware, the speaker uses its supplied screws and the same geometry serves the driver and passenger sides. Match the speaker basket and mounting pattern, protect wiring, use material suitable for cabin heat and vibration, tighten hardware evenly and confirm the speaker, trim and wiring remain secure without rattles.

Fits G-Class · W463

Custom cup holder that the creator states is made for this vehicle generation and attached with a zip tie. The publication supplies one STL and only a CAD-render source image; it gives no material, print settings, exact mounting location or long-term test evidence. Check container diameter, attachment-point strength and clearances, use cabin-heat-resistant material and secure it so neither the holder nor a drink can obstruct controls or occupants or become loose under braking.

Fits G-Class · W463

Small cover for the windscreen-wiper spindle nut on 1990s vehicles. The source shows the physical cover fitted around a wiper pivot and supplies one STL, but states no material or print settings. Match the spindle and nut dimensions, use weather-, UV- and heat-resistant material, preserve full wiper-arm clearance and verify complete sweep and secure retention before road use.

Fits G-Class · W463

Replacement interior door-panel clip for 1990s vehicles. The source includes a physical image of the clip installed in the door-panel mounting point and a CAD render, but gives no material or print settings and no exact Mercedes child-component number. Match the original clip and panel hole, remove supports and sharp edges, press-fit without forcing brittle trim and confirm the panel is fully retained before driving.

Fits G-Class · W463

Storage tray for 1990s vehicles, shown fitted in the dashboard opening beside the audio unit. The author supplies divided and undivided STL variants plus the undivided STEP source. No material or print settings are stated. Compare the opening and adjacent switch/audio layout before printing, use material appropriate for cabin heat, deburr the retaining features and confirm the tray and stored objects cannot interfere with controls or become loose under braking.

Fits G-Class · W463

Custom dashboard mount for a period mobile telephone, developed on a 1999 roadster and shown installed beside the centre console. The creator modified the telephone lighting separately with a resistor, parallel LED groups, a coiled cable and a 12-to-4 V converter; those electrical modifications and the phone are not part of the model. Match the phone body and dashboard position, use cabin-heat-resistant material, protect trim and wiring, fuse and insulate any electrical work independently and confirm the mount and phone cannot obstruct controls or become loose under braking.

Fits SL · R129

Storage bin replacing the obsolete cassette or CD box in the centre console. The source shows the physical bin loose and installed, recommends 0.20 mm layers and 15% infill and suggests a felt lining. The preserved 3MF loads successfully but is non-watertight in an independent mesh audit, so inspect and repair the sliced geometry before printing. The author distributes it under GNU GPL v3; the API represents that licence as Other. Use cabin-heat-resistant material, check console and selector clearances, secure any retained wiring below the opening and ensure stored objects cannot obstruct vehicle controls.

Fits SL · R129

Replacement sliding clip for the upper row of the lower door/body cladding, developed and tested on a 1999 roadster. The creator reports more than three months of exterior Texas use from 27–44 °C and testing to 233 km/h, specifies vertical print orientation, grid infill and 15% infill, and warns that higher infill reduced performance. The creator was told that similar cladding on 124- and 140-series cars may use it but could not confirm that fitment, so no cross-generation link is added. Compare the original upper clip and cladding rail, use UV-, heat- and impact-resistant material and confirm the panel remains secure at road speed.

Fits SL · R129

Three-piece replacement bushing for the 16 mm ball joint between the windscreen-wiper arm and motor linkage. The creator printed it in PETG at 100% infill, fitted it around the ball joint, bonded the pieces and recommends lubrication. Match the ball diameter and linkage version, use wear-, heat- and moisture-resistant material, preserve free articulation and bench-test full sweep, parking and stall behavior before wet-road use; inspect the bonded joint regularly.

Fits SL · R129

Replacement outer tab for adjusting dashboard air-vent direction. The source explicitly identifies SL roadster fitment and states that only the visible outer portion is modeled; its sole source image is a CAD render. Compare the vent version and remaining inner mechanism, use cabin-heat-resistant material, deburr the contact surfaces and verify unrestricted vane travel without stressing the original vent.

Fits SL · R129

Replacement knob for the access cover on the high-mounted stop-lamp assembly. The creator instructs removing the broken knob base, bonding this print in its place and printing sideways for strength. The cited 1297500039 number identifies the surrounding lamp-cover assembly rather than this repair fragment and is not assigned. Use cabin-heat- and UV-resistant material, choose adhesive compatible with the original plastic and verify that the cover remains secure and the stop lamp operates correctly.

Fits SL · R129

Replacement sliding clip that retains the rear-lamp bulb-carrier assembly. The creator removed the reflector, installed the printed clip, lubricated its sliding faces and reports that it holds the carrier in place. The stated 1298201577, 1298200577 and 1298200677 numbers identify complete lamp assemblies, not this printed child, so they are not assigned. Print with the circular opening toward the bed, use ABS or another heat- and weather-resistant material, verify smooth clip travel and carrier retention, then test every rear lamp before driving.

Fits SL · R129

Direct replacement for the hidden hinge base inside the leather-covered door-mounted cup holder, developed on a 300E from the 1984-1996 period. Source photographs show the physical base and cup-holder assembly. Match the door and holder variant, reuse the original covering and backing carefully, use tough cabin-heat-resistant material, and verify full folding travel, secure retention and unobstructed door operation.

Fits E-Class · W124 / S124 / C124 / A124

Replacement drain grommet for the plastic box below the right headlamp on the air-intake side. The creator states all 124-series chassis, a slightly tighter body fit and a changed drain shape. Use heat-, weather- and fluid-resistant flexible material, confirm the right-side box and opening, preserve an unobstructed downward drain path, and verify the grommet cannot admit water to wiring or the air intake.

Fits E-Class · W124 / S124 / C124 / A124

Standard- and loose-fit replacement grommets for mounting the hydraulic self-levelling suspension oil reservoir on estate cars. The creator identifies the exact child as A1299971681. These grommets support only the reservoir, not a suspension load path. Use oil-, heat- and vibration-resistant flexible material, match the mounting hole and reservoir pin, and inspect for leaks and secure retention after installation.

Fits E-Class · W124 / S124 / C124 / A124

Replacement grommet through which the radiator lower locating prongs pass. The source establishes 124-series fitment but provides only model imagery. This grommet isolates and locates the radiator; it is not a structural vehicle mount. Compare the original opening and radiator pin, use engine-bay heat-, coolant- and vibration-resistant flexible material, and confirm secure seating, fan clearance and leak-free hoses after installation.

Fits E-Class · W124 / S124 / C124 / A124

Two replacement shaft-lock variants for the headlamp-wiper motor assembly: K for SWF motors and L for SWF or Bosch motors. The creator tested both on original assemblies and documents the installed position. Identify the motor maker before printing, use heat- and weather-resistant material, preserve cable potting, and bench-test motor retention, full sweep and parking before road use.

Fits E-Class · W124 / S124 / C124 / A124

Direct replacement for the lower condenser mounting grommet identified by the creator as A2019970381. The source model intentionally simplifies fillets and tightens the fit for printing. Compare the original grommet and condenser pin, use heat-, weather- and vibration-resistant flexible material, and confirm the condenser is retained without metal-to-metal contact or stressed refrigerant lines.

Fits E-Class · W124 / S124 / C124 / A124

Replacement clip used in pairs to secure the lower engine wiring harness to the engine block; the creator notes that the same size also appears elsewhere. Exact routing varies with engine and model year, so compare the original clip and mounting point rather than inferring other positions. Use engine-bay heat-, oil- and vibration-resistant insulating material, avoid sharp wire contact and confirm the harness cannot reach hot or moving parts.

Fits E-Class · W124 / S124 / C124 / A124