Find your next part.

Two rear headlamp covers—one oblong and one small round cover—made by the creator for their first-generation SUV. The creator states that the small round cover needs light sanding to reduce visible faceting and recommends finishing the printed surfaces with varnish. Confirm headlamp housing and cover geometry before use.

Fits M-Class / GLE · W163

Retaining-clip variants for the exterior trim strip below the headlamp. Exact source fitment is the first-generation SUV; the creator includes an elongated version that held the strip more securely on their vehicle. Three author OBJ variants are supplied. Compare the original clip and trim engagement before choosing a file.

Fits M-Class / GLE · W163

Replacement windshield-washer-fluid reservoir cap proven by the creator on a 1999 first-generation SUV. The source reports that the original cap crumbles with age and that the replacement was printed successfully in dual-colour ABS; the colour change was made 1 mm into the print. Verify the cap profile against the vehicle before installation.

Fits M-Class / GLE · W163

Replacement left retaining hook/clip for the rear trim panel of a front seat. The creator identifies the exact child as A2089130172 for the 208-series and states that the model can be mirrored in the slicer for the opposite side. Mercedes official evidence calls A2089130172 the left hook, and PartSouq search evidence corroborates its front-seat-trim function. The OEM number applies only to the supplied left-side geometry; no right-side number is inferred for a mirrored print. Seat type, upholstery and option differences can affect fit, so verify by VIN and compare the original before fitting.

Fits CLK · C208 / A208

Second-version 150 mm phone holder published by the creator specifically for the CLK 208-series. The preserved source provides the author STL and a CAD image but no installed photograph, mounting instructions, material recommendation or body/facelift limitation. Compare the geometry and attachment area with the vehicle before printing, test retention at low speed, and keep the device clear of airbags, controls and the driver's sight line.

Fits CLK · C208 / A208

Replacement trim insert for the wind-deflector net opening of the late-1990s CLK convertible, modeled after the creator broke the original while removing the rear trim. The source shows the original and replacement together and the printed part installed. Mirror the supplied model in the slicer for the opposite side, then sand, prime and paint as needed. Transfer the original small flap and spring to the print; the creator does not publish a separately serviced Mercedes child number, so no wind-deflector or rear-trim parent assembly number is assigned. Confirm A208 trim and side geometry before installation.

Fits CLK · C208 / A208

Rear-position exterior cover for the side-skirt jacking opening, published for the CLK 208-series and shown installed on the creator's photographed coupe trim. Print vertically with supports and three wall lines to strengthen the hooks, using ABS or a similarly suitable material as the creator recommends. The source does not identify side, facelift, AMG/standard trim, option code or an exact molded number; compare the original opening and retainers before use. No OEM number is inferred from the cover's location.

Fits CLK · C208 / A208

Front-position exterior cover for the side-skirt jacking opening, published for the CLK 208-series and shown installed on the creator's photographed coupe trim. Print vertically with supports and three wall lines to strengthen the hooks, using ABS or a similarly suitable material as the creator recommends. The source does not identify side, facelift, AMG/standard trim, option code or an exact molded number; compare the original opening and retainers before use. No OEM number is inferred from the cover's location.

Fits CLK · C208 / A208

Replacement stop/buffer reproduced by the creator as A2107500326 and explicitly tagged for CLK 208-series and E-Class 210-series cars. Mercedes official evidence identifies this exact child as an Anschlag (stop), with independent parts evidence describing a deck-lid/trunk-lid buffer. The supplied geometry is labeled with A2107500326; the earlier A2107580944 supersession is not assigned to the print. C208 coupe and W210 body/production applicability can vary, so verify the exact child by VIN and compare the original before fitting. The source does not state material, installation torque or physical validation.

Fits CLK · C208 / A208 · E-Class · W210 / S210

Passive phone cradle that the creator explicitly states fits the ventilation grilles of the CLK 208-series and E-Class W211 sedan. It snaps into the grille without tools or vehicle damage, accepts an iPhone with or without a case, and leaves a lower opening for a charging cable. The creator notes that the model may be scaled independently to suit other phones; scaling can also change the grille engagement, so confirm a secure, non-damaging fit before driving and keep the device clear of controls, sight lines and airbags.

Fits CLK · C208 / A208 · E-Class · W211 / S211

Replacement fascia panel for the dashboard radio opening. The creator explicitly identifies the first-generation A-Class application and supplies a single printable panel. Verify radio and dashboard opening dimensions before printing and retain clearance for wiring, ventilation, controls and removal access.

Fits A-Class · W168

Holder for shopping bags in the boot. The download includes an original-form replacement and a strengthened alternative intended for heavier modern bags. Choose one variant rather than installing both, confirm that it seats in the original mounting point, and keep loads modest enough not to damage the surrounding trim.

Fits A-Class · W168

Replacement retaining clip for the door weatherstrip/seal. The creator designed it after the original clip broke and reports that it performs nearly as well as the original component. Use an automotive-temperature-capable material, compare the printed clip against an intact original before installation, and replace it if the seal is not held securely.

Fits A-Class · W168

Replacement floor air-ventilation grille identified by the creator as A63882701397C65. Source photographs show the physical grille installed in the carpeted floor opening. Use tough cabin-heat- and abrasion-resistant material, match the opening and colour/trim version, clear every slot and edge, seat the grille flush without trapping carpet, and confirm unrestricted airflow and clearance from feet, seats and movable interior fittings.

Fits Vito / Viano / V-Class · W638

Two internal replacement parts for the gear-selector mechanism. The creator identifies exact chassis fitment, supplies a physical source photograph and states that one O-ring is required to retain the assembly. The archived files were 3MF containers carrying misleading STL extensions and are preserved for upload with corrected .3mf filenames. Compare both original profiles and the selector version, use tough cabin-heat- and wear-resistant material, fit an oil-compatible O-ring of the correct size, and verify every gear position, detent, indication and interlock repeatedly with the vehicle stationary before road use.

Fits Vito / Viano / V-Class · W638

Replacement horizontal-fin assembly for the internal front dashboard vent nozzle. The creator reverse engineered the part from a van, had it printed in nylon and used it in the left vent; the source only suggests, rather than proves, that other front vents share the same internal geometry. Match the original left-side fin assembly before use, print in tough cabin-heat-resistant material, finish the pivots without removing retention features, and confirm every fin moves freely, stays aligned and does not obstruct airflow.

Fits Vito / Viano / V-Class · W638

Replacement stop for the rear/tailgate door locking mechanism, identified by the creator and model filename as 6387400003. Source photographs show the loose original-style child from both sides. Use a tough, weather- and impact-resistant material, compare the mounting and contact faces with the original, preserve latch and seal clearances, and verify the rear door closes, latches, opens and remains aligned without binding before driving.

Fits Vito / Viano / V-Class · W638

Adapter for mounting a CubeNest PowerCube S1C0 or similar charger to the original cup-holder tray. The creator specifies a 200-series R170 car, printed it in ASA and supplies photographs of the physical adapter loose and installed with a charger. Confirm the tray and charger geometry, use cabin-heat-resistant material, keep controls and sight lines clear, route and fuse any charging cable safely and verify the holder and device cannot detach under braking.

Fits SLK / SLC · R170

Replacement headliner cap for the emergency retractable-roof lock, explicitly identified for 1997–2004 SLK 230 Kompressor cars. The source image shows the physical cap installed; the creator recommends high-temperature PLA or PETG and reports a FILACUBE HT-PLA print survived Texas cabin heat with little distortion. Match the access opening, use cabin-heat-resistant material and confirm the cap stays secure while remaining removable for emergency roof operation.

Fits SLK / SLC · R170

Replacement dashboard side vent explicitly identified for 1997–2004 SLK 230 Kompressor cars. The source photograph shows a physical vent installed in the dashboard; the creator recommends high-temperature PLA or PETG and reports a FILACUBE HT-PLA print survived a Texas summer with very little distortion. Match the side-vent opening and original vane function, use cabin-heat-resistant material and verify secure seating and unrestricted airflow and adjustment.

Fits SLK / SLC · R170

Single-piece rear wind-deflector pattern for CNC or laser cutting, shown in a source composite installed between the roll bars. The creator recommends at least 6 mm clear acrylic and reusable black zip ties. Confirm roll-bar spacing, cabin and retractable-roof clearances, round and polish all edges, use UV- and impact-resistant sheet, secure every tie with trimmed ends away from occupants and verify the panel cannot loosen or obstruct rearward visibility.

Fits SLK / SLC · R170

Replacement cap for the windscreen-wiper spindle screw on a 1997 SLK 230. Source photographs show the physical print loose, the uncovered spindle and the cap installed. Use UV-, weather- and heat-resistant material, match the spindle and nut dimensions, press on without disturbing wiper-arm torque, preserve full arm and bonnet clearance and verify secure retention through a complete wet-screen sweep.

Fits SLK / SLC · R170

Replacement button for the deteriorated rubber retainer on the door-sill/kick-panel trim. The creator states exact SLK 230 fitment and adds a locking feature to keep the print in place; the source supplies one STL and a CAD source image but no physical installation photograph. Print button-top down in tough cabin- and weather-resistant material, compare the panel and body socket, press-fit without forcing brittle trim and confirm the sill panel is fully retained and cannot foul the door.

Fits SLK / SLC · R170

Replacement cover plate for the motor inside the right exterior mirror, designed for model years 1998–2004 after a purchased spare did not fit. The source provides one STL and a CAD source image but no physical fit photograph. The creator warns that PLA breaks easily where the motor-screw heads press into the plate. Restrict use to the right mirror and matching motor, print flat-side down in tough cabin-heat- and weather-resistant material, fit screw heads gently and verify mirror adjustment, retention and full housing clearance.

Fits SLK / SLC · R170