Find your next part.

Two-piece cup holder physically fitted in the center-console tray of a 1990 E34 525i. Its foot resists tipping, the lower bore is 64 mm and the upper opening is 82 mm with a mug-handle slot. Adjust the press fit in the actual console before bonding the halves and check shifter and handbrake clearance.

Fits 5 Series · E34

Four clip-in replacement gear-knob shapes for the BMW E34 and the creator-listed classic BMW chassis. The design was developed around the common BMW latching stem and includes an installed physical example. Confirm the lever's clip profile and preserve full shift travel before driving; the grouped API fitments reproduce only chassis families explicitly listed by the creator.

Fits 1 Series · E81 / E82 / E87 / E88 · 3 Series · E30 · 3 Series · E36 +14

Left/right interior mounting pod for adding tweeters in a BMW E28. The photographed print is installed in the car; the opening is intentionally generic, so select a tweeter that fits or design a separate driver adapter. Confirm mirror-image orientation, trim contour, sight lines and airbag-free mounting location before drilling or fastening.

Fits 5 Series · E28

Hand tool for aiming classic BMW headlamps that use a 3/8-inch square plastic adjuster, including E28, E24 and E23 lamps. The source provides 60, 100 and 150 mm shaft options and recommends a stiff filament. BMW numbers 63121362049 and 63121369857 identify the nut and screw being adjusted, not the printed tool, so no OEM number is assigned.

Fits 5 Series · E28 · 6 Series · E24 · 7 Series · E23

Drop-in cup holder for the BMW E28 center console, shown physically installed beside the shifter. The source is dedicated to this chassis and released to the public domain. Confirm console shape, shifter travel and access to adjacent controls before use; finish or pad contact surfaces as needed to prevent trim abrasion.

Fits 5 Series · E28

Protective cap for the top of the front strut mount on BMW E28 models. The creator printed it in PETG and road-tested the design for 5,000 miles before release. BMW catalogs identify the equivalent 28.5 mm covering cap as 31331124335; do not confuse it with the separate dust-protection collar 31331110196. Verify top-nut and mount dimensions before use.

Fits 5 Series · E28

Reinforcement bracket that replaces the flat nut at an E28 glovebox mounting point. Three prints and one M4 nut per bracket position are required to reinforce all mounting points. The creator used ABS+ and shows the parts fitted to the glovebox panel. Check screw length and ensure the bracket does not distort the glovebox shell.

Fits 5 Series · E28

Replacement throttle-body linkage/cable nipple for the M10-powered BMW E28 518i; two identical pieces are required in the catalog assembly. The design is based on an original part and includes print-orientation guidance. BMW number 13541286378 is cataloged specifically for E28 518i M10 applications and selected M10-powered E30 models, not every E28 engine.

Fits 3 Series · E30 · 5 Series · E28

Replacement roof hook for the accessory rear roller sunshade used on BMW E28, E30 and E34. It was reproduced from an original part and physically installed. BMW accessory number 82129413178 identifies the discontinued black two-piece roof-hook set; 82129413177 is the different white lower-hook style. Confirm headliner mounting, accessory configuration and color before fitting.

Fits 3 Series · E30 · 5 Series · E28 · 5 Series · E34

Replacement cap for the windshield-wiper arm retaining nut on BMW E28 and E30. The creator reproduced the current shape from an original part and reports a perfect fit. BMW number 61611370387 is the black covering cap, used on the passenger side of LHD cars and driver side of RHD cars in the creator's application; confirm side, arm style and production date by VIN.

Fits 3 Series · E30 · 5 Series · E28

Two alternative lower hook-holder geometries for the BMW accessory rear roller sunshade: an original-dimension version and a tighter-fit version tested in an early 1985 car. BMW references include discontinued white accessory hook 82129413177 and anthracite holder 51461905393, which supersedes 51461887130. E28/E30 body, production date, color and accessory installation vary; compare the no-screw-hole mounting style before use.

Fits 3 Series · E30 · 5 Series · E28

Replacement manual shifter-boot retaining frame for BMW E28 and E24 interiors. The creator measured an E28, fitted the design in the car and recommends PETG because PLA prototypes softened in cabin heat. The test car has a short shifter; correct worn or misadjusted linkage rather than relying on this frame to solve reverse-gear interference.

Fits 5 Series · E28 · 6 Series · E24

Replacement rotating knob/head for the manual sunroof crank of a BMW E28. The creator printed the part in PLA; PETG or ABS is preferable for a hot cabin. BMW catalogs supply the knob only with the complete crank handle, so no parent-assembly number is assigned. Confirm crank-pin diameter, trim color and production-date variation before fitting.

Fits 5 Series · E28

Replacement plastic retaining clip for the classic 14-inch steel wheel cover used on early BMW E28 cars. BMW catalogs identify the clip as 36131125740, used with wheel cover 36131125718 through September 1984; it is discontinued with no cataloged supersession. Verify the wheel-cover style and production date before use, and inspect every clip for secure retention.

Fits 5 Series · E28

Adjustable clutch-pedal stop body for manual-transmission BMW E28 and other listed classic BMW chassis. Assembly requires an M10 screw, two M10 nuts, a 40 mm washer and a genuine-style rubber cap. Adjust only far enough to remove excess pedal travel while preserving complete clutch disengagement, then lock the nuts securely and re-check operation before driving.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46 +4

Front and rear spacer geometry with locating rod for installing a Musway ME462 coaxial speaker in a BMW E28 sedan. The creator reports that the adapter set fits perfectly. This is specific to the stated speaker footprint; compare the mounting pattern, depth and trim clearance before printing for another driver.

Fits 5 Series · E28

Spacer and washer for fitting an upgraded 4×6-inch front speaker in a BMW E28 while retaining the original speaker cover. The creator confirms that the hood-release lever still clears the speaker and specifies longer #8×1.25-inch oval-head screws with #6-32 speed nuts. Check speaker depth and fastener clearance before final assembly.

Fits 5 Series · E28

Three-piece replacement bracket set for the BMW E28 front lower valance: left, center and right. The creator states that the parts fit in the stock locations and replaces factory brackets that commonly break or go missing. Use a UV- and heat-resistant engineering material, verify the valance variant and compare the mounting-hole geometry before fitting.

Fits 5 Series · E28

Replacement center retaining clip for the sun visor of a BMW E12 520. The creator physically fitted the part and recommends PETG, ASA, ABS or another cabin-heat-resistant material; PLA can deform in summer. BMW catalogs identify the equivalent ivory holder as 51161870863, superseding 51161820684; the photographed black print is a user-selected reproduction color, not an OEM color claim. Production date and trim variants can differ, so compare the two-hole base and visor-rod diameter before fitting.

Fits 5 Series · E12

Vent support for a Quad Lock phone interface, physically demonstrated on the right-hand-drive driver's-side center vent shared by the creator-listed BMW F30, F31 and F32. Fitment is limited to those bodies and RHD placement; F33/F36 and LHD fitment are not inferred. Use cabin-heat-resistant material, tighten without damaging the vent, and verify full vent, display, control and sightline clearance before driving.

Fits 3 Series · F30 / F31 / F34 / F80 · 4 Series · F32 / F33 / F36 / F82 / F83

Upper and lower storage trays with cutting templates for the F32/F33 center-console cavity after removal of the original phone cradle. The creator physically demonstrates both the shallow installation and the optional deeper cut-out; the cutting templates are retained as functional parts of the set. Use cabin-heat-resistant material, protect wiring before any cutting, deburr the opening, and verify secure fit and unobstructed console operation.

Fits 4 Series · F32 / F33 / F36 / F82 / F83

Three-piece detachable Qi charging stand physically demonstrated in the center cup holder of a BMW F32. It uses a user-supplied silicone Qi charging pad and routes its USB cable through the cup base; other chassis fitments are not inferred. Use cabin-heat-resistant material, electrically sound charging hardware and protected cable routing, and verify secure retention, cooling and unobstructed controls before driving.

Fits 4 Series · F32 / F33 / F36 / F82 / F83

Replacement clip and glue-in double-stud repair for broken F33 Convertible roof-frame moulding retainers, designed on and physically demonstrated with a 435i F33. The BMW clip file corresponds to superseded 51 76 7 162 587, now 51 76 5 A71 150; the custom glue-in double stud is not separately serviced and no moulding assembly number is assigned. Use heat- and UV-resistant material plus high-strength compatible adhesive, follow the creator's hook orientation, and verify full roof travel, strip retention, drainage and sealing before driving.

Fits 4 Series · F32 / F33 / F36 / F82 / F83

Clip-on key-fob holder designed and physically demonstrated in the cup-holder trim of a BMW F33 4 Series Convertible. The creator confirms the fit in his F33; no fitment to visually similar 1–4 Series interiors is inferred. Use cabin-heat-resistant material, dry-fit the clip, and verify that it cannot obstruct the controls, selector, handbrake or cup-holder use.

Fits 4 Series · F32 / F33 / F36 / F82 / F83