Find your next part.

Left and right replacement brackets for retaining the metal badge inserts in BMW G20/G21-family all-weather floor mats. The creator reports iterative fit testing and explains that the metal tabs pass through the bracket openings before the bracket is press-slid into place. Use PETG or ABS, fit only to the mat badge area, and verify the mat remains fully anchored with no loose piece or raised edge near any pedal before driving.

Fits 3 Series · G20 / G21 / G28 / G80 / G81

Console insert for BMW G20 and G21 3 Series cars without the factory wireless-charging trim, physically shown installed after removal of the original rubber mat. It accepts an Apple MagSafe puck, a 90-degree USB-C adapter and a slim 12 V USB-C adapter. Use cabin-heat-resistant material, secure and protect the cable, preserve access to controls and cup holders, and confirm the phone remains retained without obstructing driving controls.

Fits 3 Series · G20 / G21 / G28 / G80 / G81

Two-piece fold-down bag hook designed and physically demonstrated in the trunk of a BMW G20 3 Series. Install with an M6 nut, a 25–40 mm M6 socket-head bolt and a temporary nut-retaining aid as described by the creator. Use cabin-heat-resistant material, confirm the mounting point is structurally suitable, keep the load light and verify the hook and cargo cannot interfere with the trunk lid, wiring or emergency equipment.

Fits 3 Series · G20 / G21 / G28 / G80 / G81

TPU clutch-stop set in 10, 12, 14 and 16 mm heights for manual BMW F3x models; the creator reports the 16 mm version installed with the factory clutch. Use the specified material, inspect layer adhesion and fit, and stop if the part interferes with safe service or pedal operation.

Fits 3 Series · F30 / F31 / F34 / F80

Scanned right-side F30/F31 headlight support bracket shown fitted in place by the creator. Use exterior-rated material and verify retention, weather sealing, lamp aim and washer operation before driving.

Fits 3 Series · F30 / F31 / F34 / F80

Clip-on shopping-bag hook demonstrated on the factory rear parcel-shelf cover of BMW F31 and G31 Touring models. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Fits 3 Series · F30 / F31 / F34 / F80 · 5 Series · G30 / G31 / G38 / F90

Parametric insert demonstrated in the sliding-cover cup holder used by BMW F30/F31 and F32/F36 LCI interiors. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Fits 3 Series · F30 / F31 / F34 / F80 · 4 Series · F32 / F33 / F36 / F82 / F83

4.5 mm depth adapter for installing a BLAM BM200W 200 mm subwoofer in the original HiFi enclosure of a BMW F34 3 Series Gran Turismo. Use cabin-rated material, isolate wiring and connectors, and verify secure fit and unobstructed speaker operation.

Fits 3 Series · F30 / F31 / F34 / F80

Two-piece open- or closed-loop umbrella mount demonstrated on the inside of an F31 Touring boot lid. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Fits 3 Series · F30 / F31 / F34 / F80

Small storage bin fitted beside the handbrake lever in a BMW F30 328i. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Fits 3 Series · F30 / F31 / F34 / F80

Replacement outer fuel-filter clip designed for a 2015 F30 328d and reported by the creator to have remained installed for more than a year. Use the specified material, inspect layer adhesion and fit, and stop if the part interferes with safe service or pedal operation.

Fits 3 Series · F30 / F31 / F34 / F80

F30 cup-holder organizer for a garage-door remote, coin, keys and other small cabin items. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Fits 3 Series · F30 / F31 / F34 / F80

Small removable coin cup printed for the recessed BMW F30/F31 center cup holder. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Fits 3 Series · F30 / F31 / F34 / F80

Cup-holder insert that steadies slim beverage cans and raises a small fragrance tin for easier removal in BMW F3x interiors. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Fits 3 Series · F30 / F31 / F34 / F80

Front intake air scoop for N55-powered BMW F30/F31 335i, F32-series 435i, F20/F21 M135i and F22/F23/F87 M235i/M2 applications listed by the creator. Use heat- and exterior-rated material and verify secure retention and unobstructed intake airflow before driving.

Fits 1 Series · F20 / F21 · 2 Series · F22 / F23 / F87 · 3 Series · F30 / F31 / F34 / F80 +1

Adapter for installing a universal 100 mm speaker in the original BMW F30/F31 speaker location. Use cabin-rated material, isolate wiring and connectors, and verify secure fit and unobstructed speaker operation.

Fits 3 Series · F30 / F31 / F34 / F80

Funnel sized for the BMW F30 washer-fluid filler neck and physically shown in the engine bay. Use fluid-, heat- and UV-resistant material and verify full cap, hose, bonnet and washer clearance.

Fits 3 Series · F30 / F31 / F34 / F80

Replacement storage tray for the center-console cavity left after removing the factory phone cradle in a 2013 BMW 320. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Fits 3 Series · F30 / F31 / F34 / F80

This model replaces the chrome cap of the BMW coupe E92 extender arm with a hook that grabs the seatbelt successfully much more often than the original design. Designed to be a near perfect fit with the OEM shape. I recommend printing in ASA or ABS for the high temperatures in a car. The OEM piece easily comes off with a pry tool, then you can attach the 3d printed models with a strong double sided adhesive ( Confirm normal seat, belt and presenter movement and keep the printed part outside the restraint load path.

Fits 3 Series · E90 / E91 / E92 / E93

This is a centering tool designed for the precise installation of a SAC clutch disc between the flywheel and the pressure plate on a BMW E90 from the year 2011. Due to its adaptable design, the tool may also be compatible with models from earlier or later production years. To assist with model adjustments or integration, a STEP file of the tool has been provided. The tool was 3D printed using PLA+. Standard PLA should also be sufficient, as the component is not subjected to significant mechanical stress during use. After successfully mounting the preloaded SAC pressure plate, the centering tool must be removed before installing the transmission. This can be done by pulling it out using a screw or a pair of pliers. Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Fits 3 Series · E90 / E91 / E92 / E93

Use ABS preferably but it wont get that hot up top where this print is located so anything will work Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Fits 3 Series · E90 / E91 / E92 / E93

I used petg for this use organic supports Use fluid-, heat- and UV-resistant material and verify full wiper and washer clearance.

Fits 3 Series · E90 / E91 / E92 / E93

I added a 29mm cigarette lighter hole and a bmw logo on top of Fix3D:s model. You should probably use the original model's slicer settings. I used mostly default settings and the print could have come out better:) The bottoms of the holes are pretty thin and the other one broke on me while removing from the print bed, so I printed some BMW coasters with a diameter of 65mm and put them in the holes to hold the drinks. Printed in PETG basic Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Just a replacement washer fluid reservoir cap for a BMW E92. Insert included if you would like to print in a contrasting colour. Recommend printing upside-down, flat on the print surface. I know these are cheap to buy but “I can 3D print that!” Use fluid-, heat- and UV-resistant material and verify full wiper and washer clearance.

Fits 3 Series · E90 / E91 / E92 / E93