The parts catalog
Find your fit. Download a free file or choose a maker to print and ship your part.
2,661 matching parts
Free files. Made for your car.
C3D–01168Rear-cap extension physically fitted to an original BMW E36 fog lamp to clear the cooling fan on an LED replacement bulb while retaining the stock cap. Check bulb legality, connector strain, weather sealing, lamp clearance and heat before road use.
Fits 3 Series · E36
C3D–01167Three glue-in repair bases for the different upper, middle and lower clip positions on BMW E36 A-pillar trim. The source physically shows the damaged trim and provides position-specific geometry. Mark each original location and verify the trim remains secure around any curtain-free wiring or seals.
Fits 3 Series · E36
C3D–01166Blank plate for the E36 standard or M-style bumper fog-lamp opening, physically shown installed. The creator provides screw or drilled tie mounting. Use exterior-rated material and verify the plate is securely retained and does not obstruct required lighting or cooling.
Fits 3 Series · E36
C3D–0116550 mm inner-diameter service sleeve for pressing output-flange seals out of the 168 mm differential on a 1995 E36 318ti. The source shows the physical tool and flange. Support the housing correctly, keep the tool square, and do not reuse a damaged seal.
Fits 3 Series · E36
C3D–0116467 mm cupholder and 54 mm reducer for the square opening ahead of the armrest in an E36 Compact. The source shows both sizes physically installed with 250 ml and 500 ml cans. Verify handbrake, shifter and armrest clearance before use.
Fits 3 Series · E36
C3D–01163Replacement holder for the BMW E36 engine-bay inspection lamp, physically printed by the creator. Use ABS, nylon or another engine-bay-rated material, secure the lamp wiring away from heat and moving components, and verify the lamp cannot detach.
Fits 3 Series · E36
C3D–01162Service driver sized to install 168 mm differential output seals to the original depth on four-cylinder E36 and creator-listed Z3 applications. The source shows the physical tool on the differential. Use with a flat striking plate, measure seal depth, and inspect the seal lip before assembly.
Fits 3 Series · E36 · Z3 · E36/7 / E36/8
C3D–01161Replacement tow-eye opening cover for the E36 M-Technic/M3-style rear bumper, physically compared with the original and shown installed. The creator reports a tight fit and optional spring-clip provision. The nearby catalog number identifies the parent trim panel, so no OEM number is assigned.
Fits 3 Series · E36
C3D–01160Multi-part repair set for BMW E36 passenger air-vent knobs, arms, plugs, lever, washer and connectors. The creator physically assembled and installed the revised parts. Select the matching left/right pieces and verify every louvre moves freely without binding.
Fits 3 Series · E36
C3D–01159Left/right parcel-shelf support pin for BMW E36 Compact and E46 Compact, physically installed by the creator. BMWFans confirms the exact right support as 51468146708. Use a tough material and verify shelf engagement without overloading the side trim.
Fits 3 Series · E36 · 3 Series · E46
C3D–01158Fourth-iteration replacement for the small slider-rail clip used in creator-listed E36, E39, E46 and E53 sunroofs. The source shows the physical print and a working demonstration. Use heat-resistant material and verify full sunroof travel, anti-pinch operation and water sealing before driving.
Fits 3 Series · E36 · 3 Series · E46 · 5 Series · E39 +1
C3D–01157Grooved replacement hook for the E36 Compact parcel-shelf cord, refined from the original model and physically compared with the stock hook. Print in a tough material and verify the cord releases without cracking the shelf.
Fits 3 Series · E36
C3D–01156Replacement interior door-trim clip traced from the original and modified for strength. The source physically compares the printed clip with the original. Test one clip for panel alignment and removal before replacing the full set.
Fits 3 Series · E36
C3D–01155Press-fit E36 centre-console storage tray with separate coin and small-item areas, physically shown installed between the seats. Confirm it does not obstruct the handbrake, seat-belt buckles or seat travel.
Fits 3 Series · E36
C3D–01154Replacement centre-vent insert measured from a BMW E36 323ti Compact and physically installed with a 52 mm gauge. It sacrifices vent airflow at that position; use cabin-heat-resistant material and verify gauge, wiring and dashboard clearance.
Fits 3 Series · E36
C3D–01153Eight left/right repair rails for broken BMW E36 Coupe and M3 Coupe door-panel attachment areas. The source documents the physical repair and installed door panel. Bond and clamp each section on the correct side, allow full cure, and verify window and latch clearance.
Fits 3 Series · E36
C3D–01152Small repair cap for a damaged front-door tweeter grille on a BMW E36 325i. The source photo shows the original damage and repaired physical cover. Verify the cap cannot contact the speaker cone or loosen into the door.
Fits 3 Series · E36
C3D–01151Replacement push rivet for the 16 mm rear carpet holes in BMW E36 luggage compartments. The creator shows the finished print installed in carpet. Print in a tough material, test removal on one location, and do not force it into a smaller opening.
Fits 3 Series · E36
C3D–01150Adapter for a standard 100 mm rear ceiling speaker in a 1998 E36 318i Touring. The source physically shows the printed ring, speaker and installed assembly. Confirm cone, magnet, wiring and headliner clearance before fastening.
Fits 3 Series · E36
C3D–0114914 mm hex-drive hand tool for the star-shaped cell caps on the original battery in a 1999 E36. The source shows both the printed wrench and matching battery caps. Use only with the battery isolated, wear eye protection, and do not short the terminals.
Fits 3 Series · E36
C3D–01148Contour spacer demonstrated with aftermarket side repeaters on BMW bodywork. The creator lists E36 from October 1996, E46 sedan/Touring, E60/E61, E81/E82/E87/E88 and E90–E93 applications. Test one side before mirroring and verify the repeater remains weather-sealed and positively retained.
Fits 1 Series · E81 / E82 / E87 / E88 · 3 Series · E36 · 3 Series · E46 +2
C3D–01147Replacement beauty cap for M50, M52 and M54 engine-cover fasteners, physically shown on the engine. BMWFans identifies the exact component as cap 11121726089 and confirms E34, E36, E38, E39, E46, E53, E60/E61, E65/E66, E83, E85 and Z3 applications. Use engine-bay-rated material and keep it clear of hot or moving parts.
Fits 3 Series · E36 · 3 Series · E46 · 5 Series · E34 +8
C3D–01146Three-gauge panel for the E36 sunglasses cubby, physically installed after widening the side clips by 2 mm. The uploaded orientation is for RHD; the creator directs LHD cars to mirror the model. Cutting the original cubby is required, so dry-fit the panel and preserve OBC and switch clearance.
Fits 3 Series · E36
C3D–01145Left and right adapters for installing standard 5.25-inch rear speakers in the BMW E36 318ti Compact without cutting the original housings. The source shows the printed adapters, speaker assembly and installed housings. Verify speaker depth, wiring clearance and screw retention.
Fits 3 Series · E36