Find your next part.

Two-piece conversion for the factory 1992–1999 E36 cupholder module, flattening and widening the support for modern cans and cups. The creator used the installed insert and documents 318i, 325i, 328i and M3 fitment. Use cabin-heat-resistant material and confirm the module still clips securely.

Fits 3 Series · E36

Replacement interior door-handle trim bezel for BMW E30, E24, E28 and E23, physically printed and fitted. BMWFans confirms cover 51211876043. Print in a UV- and cabin-heat-resistant material.

Fits 3 Series · E30 · 5 Series · E28 · 6 Series · E24 +1

Replacement release handle for E30 Touring luggage-compartment side covers, physically installed and reported working with the original bent linkage rods. Verify both latches release and re-engage.

Fits 3 Series · E30

Two-piece replacement lower valance grille for late-model E30, fitted in front of the oil cooler and physically installed. BMWFans confirms cover 51711953609. Bond the halves securely and verify airflow and road retention.

Fits 3 Series · E30

Screw-on protective cover for exposed E30 front wheel-bearing spindle surfaces during restoration, washing, blasting, painting or storage. It is physically shown on the spindle and is removed before wheel-bearing assembly.

Fits 3 Series · E30

Replacement E30 exterior door and fender moulding clip. The creator reports that the imperfect reproduction holds tightly. Listed numbers 51131953927 and 51131965105 identify parent moulding assemblies, so no OEM number is assigned.

Fits 3 Series · E30

Replacement clip retaining the bulb holder in early E30 taillights, printed in PETG and physically installed. Late-light fitment is unconfirmed. The creator-listed 63211376879 resolves to an unrelated rotary knob in BMWFans, so it is intentionally omitted.

Fits 3 Series · E30

Replacement knob specifically for the late-model E30 manual sunroof crank, shown physically installed. Use cabin-heat-resistant material and verify that the crank turns and folds freely.

Fits 3 Series · E30

Replacement E30 centre-console spacer that prevents lower trim deformation, copied from the original and physically installed. BMWFans confirms spacer 51161943121.

Fits 3 Series · E30

Replacement E30 electric window-lifter spacer for mechanisms through April 1988, reproduced from the original and physically installed. BMWFans confirms spacer 51331919541; power-window mechanisms only.

Fits 3 Series · E30

Replacement latch striker for E30 Touring luggage-compartment side covers, reproduced from the original and physically shown working. BMWFans confirms latch striker 51471947370.

Fits 3 Series · E30

Replacement sliding jaw for E30 and E28 sunroof mechanisms, copied from the original and physically compared. The source provides a load-oriented two-piece print option; BMWFans confirms sliding jaw 54121933550. Verify full sunroof travel before road use.

Fits 3 Series · E30 · 5 Series · E28

Replacement front-seat rail nut cap for early cars from September 1985 onward and late-model E30, copied from and physically compared with the original. BMWFans confirms covering cap 52101941999.

Fits 3 Series · E30

Replacement front-seat rail nut cap for E30 cars built before September 1985, copied from the original and physically compared. BMWFans confirms covering cap 52101913670.

Fits 3 Series · E30

Click-fit cosmetic cap designed around the E30 wheel-lock bolt and physically fitted. The creator-listed 36131182006 identifies a complete lock set, not the printed cap, so no OEM number is assigned. Verify the cap cannot loosen near the wheel.

Fits 3 Series · E30

Replacement flexible tether for the E30 OBD-I diagnostic connector cap, approximated from a broken original and physically used by the creator. Print in a flexible, heat-resistant material and verify cap retention.

Fits 3 Series · E30

Replacement bracing cover for early-model E30 fog lamps, reproduced from the original and physically compared after a fit-improving revision. BMWFans confirms cover 63171373577.

Fits 3 Series · E30

Bond-on repair for a broken outer lock section on E30 Touring luggage-compartment side panels, physically demonstrated on an iX panel and mirrorable for either outer side. The referenced latch and spring are separate components and are not assigned.

Fits 3 Series · E30

Replacement front engine wiring holder for E30 M20 and creator-listed E28/E34 applications, physically compared with the original. BMWFans confirms holder 11141716134. Use ASA, ABS or another engine-bay-rated material and inspect for heat distortion.

Fits 3 Series · E30 · 5 Series · E28 · 5 Series · E34

Replacement slotted screw for retaining E30 seat-mechanism covers. The creator printed and tested revision 3.1 with a deeper screwdriver slot. Tighten only enough to retain the trim.

Fits 3 Series · E30

Five-file replacement centre-cap system for factory-style 14-inch E30 basket-weave wheels, using a face, locking clip and choice of three hex inserts. The source shows physical installation; test one assembly and verify positive retention before road use.

Fits 3 Series · E30

Short reinforced replacement lever for the brittle E30 hood-release handle, physically installed with a 4 mm or #8 screw and locknut. Print solid around the pivot and confirm reliable hood release before closing the hood.

Fits 3 Series · E30

Smooth replacement covers for the MOMO K2006 steering-wheel hub and the separately measured Alpina leather hub, physically printed and fitted on E30. Select the correct file and verify steering-column clearance.

Fits 3 Series · E30

Resin-printable replacement pivot for the E30 convertible top-lock centering mechanism, physically compared with the original. BMWFans identifies the component as covering for centering bolt 54311971255. Verify pivot movement and roof latching before driving.

Fits 3 Series · E30