Find your next part.

Factory-style switch-blank panel for a flush-mounted combined USB and 3.5 mm auxiliary extension socket.

Fits Land Cruiser · 80 Series

Workshop socket for adjusting the differential side-bearing nut, modelled for a 1991 vehicle.

Fits Land Cruiser · 80 Series

Bulkhead-mounted holder for a standard 33 cl can, with a recess for an optional 6 mm retaining magnet.

Fits Series · 1 · Series · 2

Loose- and tight-fit holders for fitting a 5 mm 12-volt LED and panel-mount bezel into a 16 mm Jaeger or Smiths gauge opening. The creator notes that the tight version may break during removal and suggests optional hot glue after installing the LED.

Fits Series · 2A · Series · 3

Door-hinge packing shims in three thicknesses. They also separate dissimilar metals to help reduce electrolytic corrosion

Fits Series · 2 · Series · 2A

Three-piece 12-volt inspection-lamp socket adaptation using standard 4 mm RC bullet connectors, 14 AWG silicone wire, and an M3 x 12 mm fastener.

Fits Series · 1 · Series · 2

Six-piece replacement kit redrawn from surviving original plastic and bakelite wiper-motor components. The positive-terminal insulator uses a simplified M3 through-bolt connection.

Fits Series · 1 · Series · 2 · Series · 2A

Replacement ventilator control knob modelled from the original component.

Fits Series · 2

Stable funnel that sleeves over the 18 mm AdBlue filler tube and rests on the adjacent air intake. It has approximately half-litre capacity, 3 mm debris-filter holes, an air-escape tube to prevent glugging, and a measured gravity-flow rate of about two litres per minute. A separate 1.7-litre pouring jug is included.

Fits Range Rover · L405

Workshop tool for installing the front crankshaft seal on 2.2- and 2.4-litre Puma engines.

Fits Defender · Puma

Replacement speaker-grille cover for the 1998 50th Edition, supplied as one complete piece or two halves for smaller printers.

Fits Defender · 300 Tdi

Cubby-box extension with two cup recesses and a central storage pocket.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Workshop tool for seating the oil seal in an LT230 transfer box. The creator printed it in PETG with a 2 mm shell and 50% infill.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Workshop wrench for removing and tightening the fuel-sender retaining ring.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Bracket for mounting a 2016 Elinz FHD dashcam at the passenger sun-visor fixing point, reusing the original visor screw.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Two fit variants of a blanking plate for the 1998 dashboard ashtray opening.

Fits Defender · 300 Tdi · Defender · Td5

Cubby-box dock for a cased Samsung Galaxy S5 and a cylindrical Qi charging puck.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Ashtray-slot phone holder for the pre-Puma dashboard.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Replacement windscreen-washer reservoir cap with retaining-ring eyelet, spill-reducing internal lips, and a 0.4 mm vent hole.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Two replacements for the unused 1998 centre-panel opening: a plain plug and a post-mounted version for a small air freshener.

Fits Defender · 300 Tdi · Defender · Td5

Three-piece adaptor set for fitting a 1995 Ford F-150 throttle-position sensor to a 1994 3.9-litre V8 throttle body. The creator specifies PETG for engine-bay heat resistance.

Fits Defender · 300 Tdi

Printable male connector bodies and mounting parts for the original dashboard E-switch and hazard-switch positions.

Fits Defender · Td5

Multi-part dashboard housing, frame, gauge mount, button, adaptor, and support bracket for the BinOwl onboard-computer installation.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Replacement interior end cap for the roof reinforcement bar.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1