Find your next part.

Modular dashboard panel for three rectangular switches, supplied as a one-piece version and a split panel with end cap.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Dashboard mounting bracket for a Garmin navigation unit in the Puma interior.

Fits Defender · Puma

Two dashboard vent inserts that redirect cabin airflow.

Fits Defender · Puma

Two-part dashboard hanger and extension for an Anker Soundcore Motion Boom portable speaker.

Fits Defender · 200 Tdi · Defender · 300 Tdi

Push-fit 27 mm wheel-nut cover.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Replacement flange for repairing or upgrading the Td5 air-filter housing connection.

Fits Defender · Td5

Dashboard holder for mounting a compact CB radio in the Puma interior.

Fits Defender · Puma

Three panel variants for combining switches and a voltmeter, designed for the 200 Tdi dashboard.

Fits Defender · 200 Tdi

Two headlining fastener sizes for a 110.

Fits Defender · Td5

Bezel for installing a 30 mm USB charging outlet in the unused position beside the rear-wiper control on the centre console. The USB outlet clamps the bezel in place.

Fits Defender · Td5

Clip-in dashboard-vent deflector that directs part of the demister airflow towards the side window. The creator positions it over the vent funnel, about 150 mm from the outer end.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Eleven thickness variants of the isolating shim fitted between the chassis brackets and rear tub to separate dissimilar metals.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +5

Replacement latch insert for the truck-cab rear sliding window, designed to reuse the original latch housing.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Five-piece double-DIN stereo binnacle for the pre-Td5 dashboard. Assembly uses twelve M4 countersunk bolts and twelve M4 nuts.

Fits Defender · 200 Tdi · Defender · 300 Tdi

Air-intake vent that replaces the removable seat-box floor grommet when fitting a diesel night heater. The creator secured it with marine sealant.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Console for mounting auxiliary switches or other equipment in the small driver-side dashboard recess. Blank and pre-drilled versions are included for both left- and right-hand-drive vehicles

Fits Defender · L663

Base-plate adapter for fitting GMC/Chevrolet pickup tie-down anchors to the cargo-area ceiling. Installation uses two 3/8 × 1.5-inch carriage bolts with washers and nuts.

Fits Defender · L663

Replacement lettered knob for a missing bulkhead-vent control. It is designed to be heat-pressed onto the original mechanism

Fits Series · 3

Replacement UP–DOWN heater airflow control button. Compare the lever slot and lettering orientation with the original before printing and fitting.

Fits Series · 2 · Series · 2A · Series · 3

Three-part replacement socket assembly for an indicator or position lamp using a separate single-contact bulb holder. Verify the 33 mm housing fit, wiring, insulation, and weather sealing.

Fits Series · 1 · Series · 2 · Series · 2A +1

Temporary reservoir cap for pressure-assisted brake bleeding. Inspect the print, seal, and hose connection carefully and use only low, controlled pressure.

Fits Series · 3

Simple cab hook for retaining a loose seat belt when it is not in use. Confirm the mounting position and belt clearance before drilling or attaching it.

Fits Series · 3

Workshop mandrel for centring the clutch plate during assembly. Confirm the spigot and spline diameters against the gearbox input shaft and clutch before use.

Fits Series · 2 · Series · 2A · Series · 3

Left- and right-hand enclosures for 100 mm speakers up to approximately 48 mm deep. Mirrored and split-file variants are included

Fits Series · 3