Find your next part.

Two-piece passenger-side interior door-pull conversion with a GT3-like shape. The creator says to mirror the files for the opposite side and attach the pull strap with a small screw.

Fits 911 · 997

Replacement cap for the Cabriolet hardtop-latch opening. The creator says it hides the latch mechanism, may need approximately 1% scale adjustment depending on printer accuracy, and should be printed flat-side down.

Fits 911 · 996

Single-piece center-console drink holder with two circular wells. The creator's photograph shows the physical print installed between the seats.

Fits 911 · 964 · 911 · 993

Phone mount that clips around an 82 mm dashboard gauge and accepts a WizGear magnetic holder.

Fits 911 · 964 · 911 · 993

Cabin-mounted mobile phone holder designed to accept an added wireless charger.

Fits 911 · 997

Replacement side mounting rail for the HEREGOES Android head unit that replaces the factory CDR30 or CDR24 stereo. V2 uses slightly oblong holes for fit adjustment.

Fits 911 · 997 · Boxster · 987 · Cayman · 987

A two-piece press-tool set for pressing 1965-1989 front control-arm rubber bushings into place.

Fits 911 · Original (901/911) · 911 · G Model

Flywheel-bolt-driven installation tool that seats the rear main seal 13 mm below the crank flange; its orientation relief clears the flywheel-flange rivet.

Fits 911 · 996 · Boxster · 986

Glue-in replacement tab for a broken sun-visor vanity-mirror housing. The creator instructs filing away excess plastic, bonding the tab with superglue, and printing slowly or increasing minimum layer time.

Fits 911 · 991 · Boxster · 981 · Boxster · 982 (718 Boxster) +2

Replacement control knob for the Becker CDR-220 radio.

Fits 911 · 996

Replacement button for a functioning remote key when the original plastic button is broken. Neutral white filament can transmit the remote’s red status LED.

Fits 911 · 997

Cupholder-mounted MagSafe phone stand for PDK interiors with the deeper cupholder slot. The creator recommends PLA+ or carbon-fiber PLA and states the design was tested only on the 992.2.

Fits 911 · 992

Plastic latching receptacle that fits into the front luggage-compartment battery bracket and receives the quarter-turn battery-cover screw plug.

Fits 911 · 996 · Boxster · 987

Replacement insulating bushing for the steering-wheel horn mechanism.

Fits 911 · G Model · 928 · 928 · 944 · 944

Replacement bar for a custom split rear grille, supplied as a one-piece version and as top and bottom printable alternatives.

Fits 911 · 993

Clutch alignment tool for a 2004 Carrera with 23 splines, 1-inch diameter and 15 mm pilot hole; includes the two tool sections and their assembly ring.

Fits 911 · 996

Clip fitted beneath the light switch so the lights turn on and off with the vehicle.

Fits 911 · 996

Replacement sliding-face-plate quadrant gear for 2002–2005 cars, supplied as left- and right-hand-drive variants.

Fits 911 · 996

Two-piece cup holder that mounts with the existing screws after removal of the ashtray-delete rubber liner while retaining access to the storage compartment.

Fits 911 · 996

Closeout panel for the center-console delete opening.

Fits 911 · 996

Three-piece MagSafe holder that clips beside the glovebox, reducing leather contact and avoiding interference with the gear lever. Sized for a 46 mm inner / 54 mm outer magnet ring.

Fits 911 · 991

Phone mount that fits between the side trim of the PCM and is sized for a Google Pixel 5 in a silicone case.

Fits 911 · 997

Replacement tensioner for the factory cupholder. The friction-fit design can function if the original small spring is missing.

Fits 911 · 997

Cupholder installed in the bin between the rear seats and secured by the lower-seat-squab nut. Includes the required nut cover plus optional narrow-cup insert and flexible liner.

Fits 911 · 991