The parts catalog
Find your fit. Download a free file or choose a maker to print and ship your part.
133 matching parts
Free files. Made for your car.
C3D–00774Complete repair set for the missing or cracked center and side vents in a 2002 TJ, including housings, vanes, sliders and geared control pieces. The creator printed prototypes and specifies heat-resistant material for service use.
Fits Wrangler · TJ
C3D–00808Modular Wrangler JL dashboard-rail mounting set with heat-resistant printable bases, arms, 20 mm ball adapters, magnetic base, and left/right holders for 67 Designs-compatible rails.
Fits Wrangler · JL
C3D–00711Printable rear lamp housing with deeper lens-screw holes, a wiring opening and internal rails for the included red-and-clear lens separator. The source recommends heat-resistant material and provides both printable parts.
Fits CJ · CJ-5 · CJ · CJ-7 · CJ · CJ-8 Scrambler +1
C3D–00777Auxiliary round-rocker switch panel shaped to the curved radio bezel used on 2011–2018 Wrangler JK and JKU interiors. Installation requires holes behind the panel.
Fits Wrangler · JK
C3D–00719Driver- and passenger-side replacement handles for paddle-style doors. The creator tested the design in a 1981 CJ-7 and states YJ and TJ compatibility, while warning that earlier non-paddle doors differ.
Fits CJ · CJ-7 · Wrangler · YJ · Wrangler · TJ
C3D–00703Three-piece replacement cupholder with a 3.5-inch front pocket, a 1.91-inch rear pocket and a separate base that can be glued or screwed in place.
Fits Wrangler · YJ
C3D–00701Replacement end clip for broken mechanical heater-control cables. The creator verified it on 1991 controls and identifies select CJ, YJ and XJ applications; fit and cable travel should be checked before reassembly.
Fits Cherokee / Liberty · XJ · CJ · CJ-5 · CJ · CJ-7 +2
C3D–00798Low-profile fog-light mount for a Wrangler JK aftermarket bumper where a winch interferes with the factory cup. It moves the original fog lamp forward approximately 13 mm.
Fits Wrangler · JK
C3D–00789Holder for a 14 mm aftermarket hands-free microphone in the factory UConnect microphone position of a Wrangler JK. Rounded and squared holder variants are included.
Fits Wrangler · JK
C3D–00807Outer bushing that fits a Hi-Lift jack climber rung around the Rampage carrier bolt to suppress rattling. The creator states JK and JL fitment.
Fits Wrangler · JK · Wrangler · JL
C3D–00802Printable hand knob assembly for Wrangler JK Freedom-panel bolts. It captures an M8 × 1.25 × 75 mm bolt for tool-free panel retention.
Fits Wrangler · JK
C3D–00799Right-hand passenger sun-visor pivot mount modeled after the broken mount in a Wrangler JK. It allows repair without replacing the complete visor assembly.
Fits Wrangler · JK
C3D–00790Replacement climate-control knob shell modeled for a 2010 Wrangler JK dashboard. Confirm shaft fit before pressing it fully into place.
Fits Wrangler · JK
C3D–00775Clip-in defrost-air diverter for 2007–2010 Wrangler JK dashboards. It redirects air from the short factory grille toward the outer windshield edges.
Fits Wrangler · JK
C3D–00773Replacement holder for a 5/16-inch square hardtop mounting nut, modeled from the retainers found in the creator's TJ.
Fits Wrangler · TJ
C3D–00725Cupholder that uses the stock windshield-mount-plate holes on late CJ and YJ vehicles without the factory dash pad. It is sized for a mug with a carabiner handle and the creator test-fitted a PETG print.
Fits CJ · CJ-5 · CJ · CJ-7 · CJ · CJ-8 Scrambler +1
C3D–00712Flexible gasket that seals between the rectangular taillight housing and lens. The source specifies TPU and the mounting pattern is documented across late CJ, YJ and TJ applications.
Fits CJ · CJ-5 · CJ · CJ-7 · CJ · CJ-8 Scrambler +2
C3D–00986Two-piece six-switch panel that replaces the right-side media-center trim in Wrangler JL and Gladiator JT dashboards. The rear plate and switch retaining nuts clamp the assembly around the factory opening.
Fits Gladiator · JT · Wrangler · JL
C3D–00985Two-piece dashboard-pocket mount for a Yaesu FTM-500 control head in Wrangler JL and Gladiator JT vehicles. It requires no vehicle drilling and the source documents the installed assembly from three angles.
Fits Gladiator · JT · Wrangler · JL
C3D–00984Compact replacement housing for Wrangler JL and Gladiator JT key-fob electronics, factory buttons, battery, and screws. The selected revision-four top and bottom incorporate the creator's fit and stiffness updates.
Fits Gladiator · JT · Wrangler · JL
C3D–00981Two-piece protective shell for Wrangler JL and Gladiator JT key fobs. The bolted enclosure shields the panic button from accidental pocket presses while retaining access to the normal controls.
Fits Gladiator · JT · Wrangler · JL
C3D–00975Vehicle-specific dashboard-pocket mount for the ICOM IC-7100 control head in Wrangler JL and Gladiator JT interiors. The source documents several weeks of installed use and uses removable hook-and-loop fastening.
Fits Gladiator · JT · Wrangler · JL
C3D–00974Nonconductive bracket for a Warn winch power-interrupt solenoid in the Gladiator JT engine bay. It uses an otherwise unused passenger-side body hole with an M6 rivnut; the creator also reports confirmed fitment from Wrangler JL and JLU owners.
Fits Gladiator · JT · Wrangler · JL
C3D–00971Snap-on flashlight holder for the factory front-seat track in Wrangler JL and Gladiator JT vehicles. It installs without drilling and the source documents both the printed clamp and its physical fit.
Fits Gladiator · JT · Wrangler · JL