Find your next part.

Replacement interior end cap for the roof reinforcement bar.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Modular dashboard panel for three rectangular switches, supplied as a one-piece version and a split panel with end cap.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Two dashboard vent inserts that redirect cabin airflow.

Fits Defender · Puma

Two-part dashboard hanger and extension for an Anker Soundcore Motion Boom portable speaker.

Fits Defender · 200 Tdi · Defender · 300 Tdi

Dashboard holder for mounting a compact CB radio in the Puma interior.

Fits Defender · Puma

Three panel variants for combining switches and a voltmeter, designed for the 200 Tdi dashboard.

Fits Defender · 200 Tdi

Bezel for installing a 30 mm USB charging outlet in the unused position beside the rear-wiper control on the centre console. The USB outlet clamps the bezel in place.

Fits Defender · Td5

Replacement latch insert for the truck-cab rear sliding window, designed to reuse the original latch housing.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Five-piece double-DIN stereo binnacle for the pre-Td5 dashboard. Assembly uses twelve M4 countersunk bolts and twelve M4 nuts.

Fits Defender · 200 Tdi · Defender · 300 Tdi

Temporary reservoir cap for pressure-assisted brake bleeding. Inspect the print, seal, and hose connection carefully and use only low, controlled pressure.

Fits Series · 3

Left- and right-hand enclosures for 100 mm speakers up to approximately 48 mm deep. Mirrored and split-file variants are included

Fits Series · 3

Slightly oversized 16 mm bonnet-hinge bush intended to reduce movement and rattling in worn hinge carriers. Print with strong layer bonding and high infill

Fits Series · 3

Modular dashboard base with two M6 attachment points, plus compatible Garmin and Motorola device holders. The base attaches to the vinyl dashboard with automotive-grade double-sided tape.

Fits Series · 3

Replacement bush used with a standard 5/16-inch bolt and locking nut to align the brake shoes. Tap the printed bore to suit the bolt thread and follow the source adjustment method.

Fits Series · 1 · Series · 2 · Series · 2A +1

Three-part loadspace-light conversion comprising an installation template, switch panel, and blanking plate. Wiring polarity and switching differ between early and later vehicles, so verify the circuit before modification.

Fits Freelander · 2

Deep dashboard-console mount for integrating a seven-inch tablet. Installation requires electrical adaptation and modification of the tablet controls

Fits Freelander · 2

Multi-part workshop tool for removing and installing the cabin blower motor. It requires M5 threaded rod, nuts, bolts, and bonded inserts

Fits Freelander · 2

Bolt-on lower clip and rotating sleeve for repairing the glovebox damper. Install with an M3 × 16 mm fastener, nut, and locking washer, and orient the clip for strength as shown by the source.

Fits Freelander · 2

Replacement internal gear set for a failed tailgate-lock actuator. Three printable variants are included

Fits Freelander · 2

Support ring fitted beneath the fuel-cap thread seal to improve compression and help prevent evaporative-system leaks.

Fits Freelander · 2

Two-piece overlay repair for a broken glovebox-damper attachment. The body clips over the damaged damper and a half-ring lock provides additional retention.

Fits Freelander · 2

Two-piece coin organiser for the centre-console area, comprising a main holder and lid.

Fits Freelander · 2

Replacement plunger for a broken fuel-filler-door actuator.

Fits Discovery · 3 · Discovery · 4 · Range Rover Sport · L320

Two replacement locating-pin variants for the loadspace cover: one for an M8 opening and one for the original 11 × 11 mm square opening. Print horizontally to reduce delamination risk.

Fits Range Rover · L322