Find your next part.

Replacement centre dashboard air vent recreated after the original in a 1976 Porsche 911 cracked. The creator reports that the ABS print fit perfectly and provides plain and brim-supported STL variants.

Fits 911 · G Model

Flywheel-bolt-driven installation tool that seats the rear main seal 13 mm below the crank flange; its orientation relief clears the flywheel-flange rivet.

Fits 911 · 996 · Boxster · 986

Glue-in replacement tab for a broken sun-visor vanity-mirror housing. The creator instructs filing away excess plastic, bonding the tab with superglue, and printing slowly or increasing minimum layer time.

Fits 911 · 991 · Boxster · 981 · Boxster · 982 (718 Boxster) +2

Single-piece holder for an iPhone-compatible MagSafe charging puck that fits the covered cigarette-lighter compartment of a smoker-package center console. The recessed body retains the puck and stores its cable; the creator printed the part in PLA with supports.

Fits Macan · 95B

Replacement push lugs for the window switches. The creator intentionally made them long so they can be trimmed to length.

Fits 147 · Tipo 937 · GT · Tipo 937

Lower movable mounting bracket for an Alfa Romeo Stelvio headlight, designed as an alternative to the complete headlamp repair kit.

Fits Stelvio · Tipo 949

Replacement hinge for the under-carpet luggage-compartment floor panel in the source-stated estate body. Mirror the supplied model in the slicer for the opposite side. The creator recommends ABS, ASA or PETG, supports, four walls, five top and bottom layers and 50% infill, and updated the geometry to improve fit and avoid cracking caused by tight tolerances. Confirm free closing movement and screw-slot adjustment before loading the panel. Creator-stated A2136846900 was researched but is not assigned because official listings identify that number as a cover rail rather than this printed hinge child.

Fits E-Class · W213 / S213 / C238 / A238

Two-piece mount designed for a 2018 GLC and a 12.9-inch sixth-generation iPad Pro. The vehicle-side piece slips over the factory display and accepts a soft-opening hinge so the tablet can be moved for rear-camera use. Source imagery is CAD/render evidence only. Verify the exact tablet and hinge hardware, protect the factory screen and trim, secure and strain-relieve all wiring, preserve visibility of the road, instruments and reversing image, and remove the mount if it loosens, obstructs controls, or overheats.

Fits GLK / GLC · X253 / C253

Cupholder-mounted phone cradle designed for a GLC 300 and sized for a Samsung Galaxy A51 in a folding case. Openings in the body are intended to improve phone-audio output. Fit depends on the stated phone and case envelope; verify the cradle seats fully, retains the phone during driving, remains clear of the selector and controls, and does not soften or crack in cabin heat.

Fits GLK / GLC · X253 / C253

Insert replacing the Peiker phone-preparation module position between the 12 V socket and original USB/MMI panel in the centre console. The creator verified it on a V-Class with that exact console layout and warns that other Vito variants must be compared by photographs and the stated 72 × 129 × 12 mm dimensions. Use ASA as recommended, or ABS; PETG is only cautiously suggested and PLA is excluded. Fit a dimensionally compatible MagSafe/Qi charger, use an automotive DC-DC/USB-C module with a dedicated fuse, mechanically secure and insulate every wire, check charging heat under extended use, and confirm the assembly cannot interfere with controls. Electrical installation remains at the installer’s risk.

Fits Vito / Viano / V-Class · W447

Clip-on rear-camera mount developed for the estate headliner and a Vantrue N4/N5 RC-01 rear camera. It clamps between the headliner and roof sheet without screws or holes and is shown installed clear of the tailgate. Fitment is limited to the estate body. Protect the headliner, keep the camera and cable clear of airbags, visibility and tailgate travel, and verify the mount cannot detach.

Fits C-Class · W205 / S205 / C205 / A205

Two cupholder inserts sized for 250 ml and 355 ml energy-drink cans. The creator explicitly states fitment across the sedan, estate, coupé, and cabriolet body variants and provides physical in-console images. Use a heat-resistant interior material, confirm the chosen insert seats fully, keep liquids clear of electrical controls, and stop use if the can can tip, bind, or interfere with the console lid.

Fits C-Class · W205 / S205 / C205 / A205

Work-in-progress umbrella holder for the C300 trunk, source-backed for model year 2015 onward and attached through existing factory holes with 1/4-20 by 1-inch bolts. Source images show both the physical brackets and their installed position. Use only for a light umbrella, preserve access to adjacent equipment, verify fastener engagement and trunk-lid clearance, and never use the printed brackets for cargo restraint or any safety-critical load.

Fits C-Class · W205 / S205 / C205 / A205

Three-piece iPhone 7 holder designed specifically for the original CD slot and shown installed in the source vehicle; the creator notes a thick phone case and charging lead. Match the phone, case and head-unit slot, use cabin-heat-resistant material, insert without forcing the disc mechanism and route the cable clear of controls. Verify that the holder cannot obscure controls, airbags or the road or eject the phone under braking.

Fits C-Class · W204 / S204 / C204

Replacement mounting bracket for the sun visor, explicitly titled for 2006–2018 vehicles. The source provides one printable mesh and one CAD source image but no side, cab, market or option-code split. Compare the original bracket and screw spacing before use, print in a tough cabin-heat-resistant material, retain suitable original fasteners, and verify the visor pivots and stays secured without obstructing the driver or detaching.

Fits Sprinter · W906

Two-piece retaining clip for the driver's floor mat. The creator designed and tested it on a 2011 vehicle, states that the two halves permanently snap together through the mat, and notes that removal from the floor takes slightly more force than the original. The source print used PLA with a 0.4 mm nozzle, no raft and no supports; for sustained cabin heat, prefer an automotive-temperature-capable material. Confirm that both halves are fully locked, that the mat cannot slide toward the pedals, and stop using the print if it loosens or cracks.

Fits A-Class · W169

Larger closed bottle holder derived from the center-console attachment dimensions of the creator-cited cup-holder design. It is intended for large bottles and can also serve as a small waste bin; fitment is limited to the source-stated center-console arrangement.

Fits E-Class · W211 / S211

Replacement pull clip for the factory rear side-window sunshade. The creator modeled it from the factory design, reports direct fit without modification, and recommends ABS or PETG with 0.2 mm layers and 100% infill for cabin heat resistance.

Fits E-Class · W211 / S211

Replacement link for the folding center-console cup-holder mechanism. Source photos document the original mechanism, printed part and working assembly; verify smooth movement before reinstalling the trim.

Fits E-Class · W211 / S211

Left and right rosettes for the luggage-compartment side panels around the boot-lid hinge arms. The author reports a perfect fit but instructs users to make a small cut after printing so each rosette can be installed around its arm. Molded child numbers were not independently verified, so no OEM number is assigned.

Fits E-Class · W211 / S211

Exterior rear-window cover for the estate body, replacing the corroded metal cover around the rear-wiper shaft. Bond with automotive glass adhesive or sealing silicone and retain the source-stated estate-only fitment.

Fits E-Class · W211 / S211

Replacement opening handle for the storage compartment below either front seat. Print vertically with support beneath the hinge features and verify hinge movement before loading the compartment.

Fits E-Class · W211 / S211

Two-part landscape phone mount for the center vent. The author tested the printed ABS part on an Avantgarde right-hand-drive car, warns that vent and trim variants may differ, and advises against PLA because of cabin heat. Removal may require gently opening the vent vane with a spudger.

Fits E-Class · W211 / S211

Replacement lever made after the originals broke on W203/S203 seats. The creator reports PLA loosening after sun exposure and successful use in PETG. Compare the lever shaft and seat-control version, use tough cabin-heat-resistant material, fit without forcing the switch and confirm every seat adjustment operates normally and the lever remains secure; this file does not replace structural seat or restraint hardware.

Fits C-Class · W203 / S203 / CL203