Find your next part.

Internal replacement gear for the original blend-door actuator used in the creator’s ML 320. The source identifies A1638200108 as the complete actuator, not as this printed child gear, so that parent assembly number is not assigned. The creator warns that aftermarket motors may differ, tolerances are very tight, and sizing may need adjustment. Print in ABS at 100% infill; PLA is explicitly not recommended. Mark the metal-shaft position before disassembly, reinstall the gear with the flat side up, and preserve the original actuator orientation.

Fits M-Class / GLE · W163

Front-position exterior cover for the side-skirt jacking opening, published for the CLK 208-series and shown installed on the creator's photographed coupe trim. Print vertically with supports and three wall lines to strengthen the hooks, using ABS or a similarly suitable material as the creator recommends. The source does not identify side, facelift, AMG/standard trim, option code or an exact molded number; compare the original opening and retainers before use. No OEM number is inferred from the cover's location.

Fits CLK · C208 / A208

Replacement headliner cap for the emergency retractable-roof lock, explicitly identified for 1997–2004 SLK 230 Kompressor cars. The source image shows the physical cap installed; the creator recommends high-temperature PLA or PETG and reports a FILACUBE HT-PLA print survived Texas cabin heat with little distortion. Match the access opening, use cabin-heat-resistant material and confirm the cap stays secure while remaining removable for emergency roof operation.

Fits SLK / SLC · R170

Replacement housing for the rear-door magnetic bumper on 2002–2006 vans. The creator cites original reference 901 740 03 16 but explicitly says this geometry is not an exact match; therefore that number is preserved only as a reference and is not assigned. Printing requires a layer pause to encase the reused original metal components, with TPU 64D or 95A specified. Inspect rust expansion, clean and protect the metal parts, confirm door alignment and magnetic retention and verify the housing cannot detach or interfere with complete door latching.

Fits Sprinter · W901–W905

Replacement cover for the front-right opening in the side-member/sill cladding. Source photographs show the installed location, the original and printed pieces, and the CAD model. EPC evidence identifies the right-front covering; use UV-, weather- and impact-resistant material, inspect the mounting opening for corrosion, and confirm the cap remains secure.

Fits 190 Series · W201

Replacement trim clip for the towing-eye cover on a 126-series car. The preserved author archive supplies the model, licence and exact fitment, while the only source image is a CAD render and no physical make is shown. Compare the original clip and cover position, use UV- and weather-resistant material, and confirm the cover cannot loosen into traffic.

Fits S-Class · W126 / C126

Two-piece replacement case for the handle portion of the original ignition key blade. The creator provides separate upper and lower shells and shows the physical case around a 123-series key. This does not reproduce or alter the metal key blade or lock coding. Verify the blade head dimensions, bond the shells securely with no adhesive on the blade cuts, and confirm the case cannot separate or obstruct full key removal.

Fits W123 Series · W123 / S123 / C123

Replacement frame for a broken rear number-plate lamp, also usable as a cutting guide for a new seal. The creator states fitment across 123-series variants. Use UV- and heat-resistant material, preserve the original lens, bulb holder and wiring, install an appropriate gasket and confirm lamp visibility, weather sealing and wire clearance.

Fits W123 Series · W123 / S123 / C123

Replacement clip joining seat upholstery to the internal metal rod. The creator explicitly states use on W123, W140 and R129 seats and recommends ABS rather than PLA. Compare the original clip and seat construction, use a tough heat-resistant material, round and clean every contact edge and confirm the upholstery is retained without cutting the fabric or affecting seat adjustment. Source-stated numbers 1239884078 and 1409883778 were not assigned because an independent exact EPC child-component mapping was not recoverable in this run.

Fits S-Class · W140 / C140 · SL · R129 · W123 Series · W123 / S123 / C123

Protective body plug test-fitted in a 123-series jacking point. The creator printed it in ABS with three flex slots and advises rust protection inside the jacking tube before installation. This is a dust and appearance plug only: remove it before using the factory jack, never treat it as a lifting pad, and inspect the jacking point for corrosion before lifting. The source mentions reference number 2018990008, but no exact EPC child-component record was independently recovered, so no OEM number is assigned.

Fits W123 Series · W123 / S123 / C123

Replacement knob for the heating and ventilation slider controls. The source explicitly covers 107-series SL and SLC controls and shows the knob fitted at the dashboard vent-control panel. Add a white indicator mark after printing if desired. Use heat-resistant material and verify smooth full slider travel without binding before driving.

Fits SL · R107

Replacement clip for the centre-console pen recess, shown installed with and without a pen and as loose physical prints. BMW services the clip only with the larger ashtray insert, so parent number 51167026219 is deliberately omitted. Confirm retention and keep loose objects clear of the handbrake and shifter.

Fits Z4 · E85 / E86

Replacement ball outlet for a cracked headlight-washer nozzle, shown loose and fitted to the original sprayer. The creator bonded the PLA part with water-resistant adhesive and notes that the bore may need careful finishing. No complete-nozzle parent number is assigned; verify sealing, spray direction, cover clearance and legal washer operation before driving.

Fits Z4 · E85 / E86

Replacement rear access cover for the high-beam bulb opening on facelift headlamp assemblies. The creator replicated a perished cover from a 2005 vehicle, physically printed the replacement in ABS and reused the original rubber seal. Public BMW catalog evidence identifies the serviced high-beam cover as 63 12 6 940 252 for facelift E53 headlamps. Use only on matching 10/2003-on headlamp assemblies, transfer an undamaged seal, use heat-resistant material and confirm a dry, secure seal before driving.

Fits X5 · E53

Replacement covering cap for the rear-window wiper arm, 3D-scanned from the original and physically shown loose, compared with the original and snapped onto the arm. BMW catalogs identify the original child component as 61687407276, rear-wiper diagram item 6, for X3 G01/G01 LCI, X3 M F97/F97 LCI and iX3 G08; Hubauer records supersession to 61625A9D577. Use ABS, ASA, PETG or another UV- and heat-resistant material, compare the clip geometry, confirm by VIN and verify secure retention and full wiper travel.

Fits iX3 · G08 · X3 · G01 / F97

Left and center replacement tabs for the movable dashboard air vents, modeled from the creator's 2007 X3 E83 and physically shown beside original vent tabs. The small movable tabs are not separately serviced by BMW; complete fresh-air grille numbers vary by position and production date, so no parent assembly number is assigned. Print in a cabin-heat-resistant material and verify smooth louver movement without rattle or binding.

Fits X3 · E83

MagSafe phone mount with a lower cable-management cavity and retaining pegs, designed to fit the factory center-console phone tray. The creator printed it in PETG and documents both the installed fit and the loose physical part with its cable routed in the cavity. Verify the pictured console, charging puck and cable dimensions before printing; use PETG or another heat-resistant material and confirm the cable and phone cannot foul the vehicle controls.

Fits iX · I20

Angled MagSafe phone mount that press-fits into the factory center-console phone tray and turns the phone toward the driver. The creator's source image shows the printed part installed with a phone attached. Verify the pictured console, viewing angle, MagSafe puck and phone/case dimensions before printing; use a heat-resistant material and ensure the phone remains secure without obstructing the controller, selector, buttons or driving visibility.

Fits iX · I20

Dashboard adapter that clips beneath the center-vent trim and provides two slots for attaching an accessory holder that would otherwise clamp directly to a vent grille. The creator shows the printed adapter installed by itself and carrying a physical magnetic phone holder, and notes that optional automotive-grade double-sided tape improves retention. This is a removable accessory rather than an original BMW component, so no OEM number is assigned. Use cabin-heat-resistant material, protect the adjacent trim, verify secure attachment and confirm that the holder, cable and device do not obstruct controls, displays, airflow or the driver's view.

Fits i5 · G60 / G61

Two-piece organizer tray for the storage compartment beneath the center armrest, with an optional flexible floor insert and an opening that preserves access to the USB-C port. The creator designed it on a 2023 eDrive40 and shows the physical tray installed empty, with a charging cable, and loose outside the vehicle. Use PETG, ASA, or another cabin-heat-resistant material for the tray and TPU for the optional insert; verify stable seating, cable clearance, and unobstructed armrest movement.

Fits i4 · G26

Two-piece smartphone mount for the iX1 U11 cockpit, with a separate ball head and tight-fit, loose-fit, or loose-fit-with-hex-nut base variants. The creator shows the printed assembly installed beside the curved display and explains that the tight version requires substantial installation force, while the loose versions require EVA foam tape and otherwise may not support the phone. This is accessory geometry rather than a serviced BMW component, so no display, trim or dashboard parent number is assigned. Use cabin-heat-resistant material, avoid excessive force on trim, keep the phone clear of sight lines and airbags, and verify secure retention before driving.

Fits X1 · U11

Removable insert for the BMW X1 F48 center-console cup holder, with separate slots for the vehicle key and a small remote. The creator identifies the F48 application and physically printed and demonstrated the insert holding both devices. This is an accessory rather than a reproduction of a separately serviced BMW component, so no cup-holder or console parent number is assigned. Use PETG, ABS, ASA or nylon rather than PLA because parked-cabin heat can deform low-temperature material; confirm the insert seats securely and does not obstruct adjacent controls or the second cup position.

Fits X1 · F48

The nasty clips at the back of the headliner which always breaks when removing. Works very well with PETG. For non commercial use only! Creator reports the PETG replacement works very well at the rear of the E61 headliner. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

The Screw in older BMW Trunks Toolboxes. E.g. e39 Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39