Find your next part.

Replacement pull clip for the factory rear side-window sunshade. The creator modeled it from the factory design, reports direct fit without modification, and recommends ABS or PETG with 0.2 mm layers and 100% infill for cabin heat resistance.

Fits E-Class · W211 / S211

Replacement link for the folding center-console cup-holder mechanism. Source photos document the original mechanism, printed part and working assembly; verify smooth movement before reinstalling the trim.

Fits E-Class · W211 / S211

Left and right rosettes for the luggage-compartment side panels around the boot-lid hinge arms. The author reports a perfect fit but instructs users to make a small cut after printing so each rosette can be installed around its arm. Molded child numbers were not independently verified, so no OEM number is assigned.

Fits E-Class · W211 / S211

Replacement opening handle for the storage compartment below either front seat. Print vertically with support beneath the hinge features and verify hinge movement before loading the compartment.

Fits E-Class · W211 / S211

Two-part landscape phone mount for the center vent. The author tested the printed ABS part on an Avantgarde right-hand-drive car, warns that vent and trim variants may differ, and advises against PLA because of cabin heat. Removal may require gently opening the vent vane with a spudger.

Fits E-Class · W211 / S211

Replacement lever made after the originals broke on W203/S203 seats. The creator reports PLA loosening after sun exposure and successful use in PETG. Compare the lever shaft and seat-control version, use tough cabin-heat-resistant material, fit without forcing the switch and confirm every seat adjustment operates normally and the lever remains secure; this file does not replace structural seat or restraint hardware.

Fits C-Class · W203 / S203 / CL203

Internal replacement gear for the original blend-door actuator used in the creator’s ML 320. The source identifies A1638200108 as the complete actuator, not as this printed child gear, so that parent assembly number is not assigned. The creator warns that aftermarket motors may differ, tolerances are very tight, and sizing may need adjustment. Print in ABS at 100% infill; PLA is explicitly not recommended. Mark the metal-shaft position before disassembly, reinstall the gear with the flat side up, and preserve the original actuator orientation.

Fits M-Class / GLE · W163

Front-position exterior cover for the side-skirt jacking opening, published for the CLK 208-series and shown installed on the creator's photographed coupe trim. Print vertically with supports and three wall lines to strengthen the hooks, using ABS or a similarly suitable material as the creator recommends. The source does not identify side, facelift, AMG/standard trim, option code or an exact molded number; compare the original opening and retainers before use. No OEM number is inferred from the cover's location.

Fits CLK · C208 / A208

Replacement headliner cap for the emergency retractable-roof lock, explicitly identified for 1997–2004 SLK 230 Kompressor cars. The source image shows the physical cap installed; the creator recommends high-temperature PLA or PETG and reports a FILACUBE HT-PLA print survived Texas cabin heat with little distortion. Match the access opening, use cabin-heat-resistant material and confirm the cap stays secure while remaining removable for emergency roof operation.

Fits SLK / SLC · R170

Replacement housing for the rear-door magnetic bumper on 2002–2006 vans. The creator cites original reference 901 740 03 16 but explicitly says this geometry is not an exact match; therefore that number is preserved only as a reference and is not assigned. Printing requires a layer pause to encase the reused original metal components, with TPU 64D or 95A specified. Inspect rust expansion, clean and protect the metal parts, confirm door alignment and magnetic retention and verify the housing cannot detach or interfere with complete door latching.

Fits Sprinter · W901–W905

Replacement trim clip for the towing-eye cover on a 126-series car. The preserved author archive supplies the model, licence and exact fitment, while the only source image is a CAD render and no physical make is shown. Compare the original clip and cover position, use UV- and weather-resistant material, and confirm the cover cannot loosen into traffic.

Fits S-Class · W126 / C126

Two replacement seat-adjustment levers for the opposite seat sides on 126-series interiors. The creator printed both successfully in ABS and emphasizes that the documented print orientation is important for strength. One preserved STL is non-watertight in an independent mesh audit, so inspect and repair the sliced geometry before printing. Compare the shaft and lever direction before choosing a side, use tough cabin-heat-resistant material, and confirm the seat locks and moves through its full range without binding.

Fits S-Class · W126 / C126

Two-piece replacement case for the handle portion of the original ignition key blade. The creator provides separate upper and lower shells and shows the physical case around a 123-series key. This does not reproduce or alter the metal key blade or lock coding. Verify the blade head dimensions, bond the shells securely with no adhesive on the blade cuts, and confirm the case cannot separate or obstruct full key removal.

Fits W123 Series · W123 / S123 / C123

Replacement frame for a broken rear number-plate lamp, also usable as a cutting guide for a new seal. The creator states fitment across 123-series variants. Use UV- and heat-resistant material, preserve the original lens, bulb holder and wiring, install an appropriate gasket and confirm lamp visibility, weather sealing and wire clearance.

Fits W123 Series · W123 / S123 / C123

Replacement clip joining seat upholstery to the internal metal rod. The creator explicitly states use on W123, W140 and R129 seats and recommends ABS rather than PLA. Compare the original clip and seat construction, use a tough heat-resistant material, round and clean every contact edge and confirm the upholstery is retained without cutting the fabric or affecting seat adjustment. Source-stated numbers 1239884078 and 1409883778 were not assigned because an independent exact EPC child-component mapping was not recoverable in this run.

Fits S-Class · W140 / C140 · SL · R129 · W123 Series · W123 / S123 / C123

Protective body plug test-fitted in a 123-series jacking point. The creator printed it in ABS with three flex slots and advises rust protection inside the jacking tube before installation. This is a dust and appearance plug only: remove it before using the factory jack, never treat it as a lifting pad, and inspect the jacking point for corrosion before lifting. The source mentions reference number 2018990008, but no exact EPC child-component record was independently recovered, so no OEM number is assigned.

Fits W123 Series · W123 / S123 / C123

Replacement knob for the heating and ventilation slider controls. The source explicitly covers 107-series SL and SLC controls and shows the knob fitted at the dashboard vent-control panel. Add a white indicator mark after printing if desired. Use heat-resistant material and verify smooth full slider travel without binding before driving.

Fits SL · R107

Replacement clip for the centre-console pen recess, shown installed with and without a pen and as loose physical prints. BMW services the clip only with the larger ashtray insert, so parent number 51167026219 is deliberately omitted. Confirm retention and keep loose objects clear of the handbrake and shifter.

Fits Z4 · E85 / E86

Replacement ball outlet for a cracked headlight-washer nozzle, shown loose and fitted to the original sprayer. The creator bonded the PLA part with water-resistant adhesive and notes that the bore may need careful finishing. No complete-nozzle parent number is assigned; verify sealing, spray direction, cover clearance and legal washer operation before driving.

Fits Z4 · E85 / E86

Longer repair guide for the Roadster and M Roadster seatbelt guide, independently remeasured after a shorter design moved in use. The creator reports successful PETG use and shows it installed. This is a trim guide, not a restraint anchor; confirm the belt feeds and retracts freely and never modify the belt or anchor.

Fits Z3 · E36/7 / E36/8

Replacement rear access cover for the high-beam bulb opening on facelift headlamp assemblies. The creator replicated a perished cover from a 2005 vehicle, physically printed the replacement in ABS and reused the original rubber seal. Public BMW catalog evidence identifies the serviced high-beam cover as 63 12 6 940 252 for facelift E53 headlamps. Use only on matching 10/2003-on headlamp assemblies, transfer an undamaged seal, use heat-resistant material and confirm a dry, secure seal before driving.

Fits X5 · E53

Drop-in frame for the factory wireless-charging pad that keeps a phone centered while leaving the charging-status LED visible. The creator recreated it on a 2021 X3 G01 for phones up to approximately 75 x 155 mm and reports using it with a device larger than the original iPhone 15-sized insert. This is an aftermarket retainer rather than the cataloged charging tray, so no parent assembly number is assigned. Confirm charging-pad and phone geometry, option equipment, charging alignment, heat, clearance and retention before driving; use PETG, ABS, ASA or another cabin-heat-resistant material.

Fits X3 · G01 / F97

Replacement covering cap for the rear-window wiper arm, 3D-scanned from the original and physically shown loose, compared with the original and snapped onto the arm. BMW catalogs identify the original child component as 61687407276, rear-wiper diagram item 6, for X3 G01/G01 LCI, X3 M F97/F97 LCI and iX3 G08; Hubauer records supersession to 61625A9D577. Use ABS, ASA, PETG or another UV- and heat-resistant material, compare the clip geometry, confirm by VIN and verify secure retention and full wiper travel.

Fits iX3 · G08 · X3 · G01 / F97

Left and center replacement tabs for the movable dashboard air vents, modeled from the creator's 2007 X3 E83 and physically shown beside original vent tabs. The small movable tabs are not separately serviced by BMW; complete fresh-air grille numbers vary by position and production date, so no parent assembly number is assigned. Print in a cabin-heat-resistant material and verify smooth louver movement without rattle or binding.

Fits X3 · E83