Find your next part.

Replacement plastic retainer for the inner upholstery/lining on the boot lid of the Volvo S40 II, 2003-2012 generation. The recovered original is a CC BY-4.0 Thingiverse design by thermaq; preserve attribution and the original source link. The public recovery page lists standard FDM guidance of 0.2 mm layers, 70% infill, and supports as needed.

Fits S40 · Second generation

Full-size functional center-console holder for retaining two phones above the cup holders in the first-generation Volvo S90 (2016-present). The source describes a friction-fit holder for the oddly shaped console area and shows physical prints in the vehicle. Verify phone/case clearance, retention, console trim protection, driver visibility, controls, airbags, and secure behavior before driving.

Fits S90 · First generation

Full-size functional replacement headlamp-washer cap holder/retainer for the first-generation Volvo S60 (2000–2009), based on the creator’s fitment statement and reported multi-year use. The source identifies original unit/retainer number 30655462, is free to download under CC BY, and requires attribution. Source-recommended materials are PETG or ASA; PETG is mapped here because ASA is not present in the active material snapshot. Verify side, nozzle/cover interface, dimensions, print orientation, heat/weather resistance, and fit before installation.

Fits S60 · First generation

Functional replacement manual gear-shift knob for the Volvo 850 (1991-1996). The source describes a push-on shaft interface with a keyway to prevent rotation and notes that scaling to 103% may be needed for the creator’s printer. Source guidance recommends PETG or ASA at 20-30% infill; verify fit and secure retention before driving.

Fits 850 · 850

Two-part, glue-assembled full-size cup holder for slim cups, designed for the Volvo 850 (1991-1996) and mounted on the seat-shift area between the front seats. The source recommends PETG or ASA for durability and heat resistance, 20-30% infill, and checking supports in the slicer. Verify fit, retention, clearance from the shifter and seats, and safe use with closed containers before driving.

Fits 850 · 850

3D-printable replacement pin for the headlamp horizontal-adjustment mechanism. The creator reports that the original pin can fail, leaving the headlamp rocking horizontally and unable to adjust, and reports installing the reinforced replacement on both headlights of a Volvo V40. The source listing identifies first-generation Volvo S40/V40 fitment. The mirrored print settings identify PLA; assess material suitability for automotive heat and service conditions before use.

Fits S40 · First generation · V40 · First generation

Replacement radio fascia phone mount with an integrated adjustable phone cradle and USB access. The creator's source lists Volvo C30, C70, S40, and V50 fitment and supplies generic-size variants, an iPhone 13 Pro Max demo, an editable STEP phone-holder part, and a Radio Fascia STL. Use a heat-resistant material for vehicle-cabin temperatures, verify dimensions and retention, and keep the device clear of controls and driver sight lines.

Fits S40 · Second generation · V50 · First generation

Functional two-file cup-holder insert for P3 Volvo XC60/S60, source-stated 2011-2017 fitment. The source images show the printed ring installed in the center-console cup-holder location and retaining a beverage can. Verify model year, chassis/console variant, fit, retention, clearances, and material suitability before use. The creator did not specify filament; PETG is engineering-inferred for cabin heat resistance. CC BY attribution terms apply.

Fits S60 · Second generation · XC60 · First generation

Two-piece functional repair for the Volvo M56 manual-transmission shifter: replacement pivot ball-seat/bushing (Volvo 9183908) and retaining shift clip (Volvo 8636988). The creator models it for a 2001 Volvo XC70 and reports compatibility with other Volvo M56/M66 manual-transmission applications using the same shifter lever. Creator guidance says ABS works and nylon is probably better; do not use carbon-fiber nylon because it is abrasive and can wear the ball joint. Verify dimensions, transmission, fit, retention, and safe operation before driving.

Fits XC70 · First generation

Roof microphone mount designed to integrate an RSNAV microphone capsule into the unused right-hand-drive microphone location of an Audi A4/S4/RS4 B8. The downloaded design is an Autodesk Fusion 360 CAD file containing BREP design data.

Fits A4 · B8

Two-piece repair kit for a retractable cargo cover: a replacement end-cap repair piece and a screw anchor/plug for the main metal rod. The parts restore shade retraction and tension; the source instructions call for fit checking, possible drilling or filing, epoxy bonding, and ABS with 100% infill. Exact fitment is Audi A4 Avant B5, 1994-2001.

Fits A4 · B5

3D-printable single-piece removal key for compatible VW/Audi radio and center-console compartment removal. Original design by Dominick Maggio (dmmaggio), licensed CC BY with attribution required. The source reports PETG use and says PLA or ABS may also be suitable; verify vehicle-specific fitment and print strength before use.

Fits Q5 · FY · Q8 · Q8

Drop-in center-console organizer with two card slots and two cylindrical openings for small items. Creator attribution: SkriptZz. Source fitment is Audi A3 8V, 2018; source print guidance specifies Sunlu PETG and 15% infill, with PETG or ASA recommended on the catalog page. CC BY-SA: commercial use allowed, attribution required, and share-alike terms apply.

Fits A3 · 8V

Custom dashboard-mounted magnetic phone-holder hook for the Audi A6 C6 (4F5), designed to accept a separate magnetic wireless charger and attach beside the dashboard air vent. The creator recommends PETG or ASA, 20-30% infill, 1.2-1.6 mm walls, and verifying supports in the slicer. Verify fit, retention, print strength, visibility, and unobstructed access to vehicle controls before use. CC BY: commercial use allowed with attribution required.

Fits A6 · C6

Replacement clip for the removable back cover of the front seat on the Audi A4 B5 (1994-2001). The creator reports that it repairs a fallen/deformed seat-back cover and can be fastened with glue or, preferably, a screw. The source recommends PETG or ASA and 20-30% infill for durability; verify the original clip profile, seat variant, attachment method, clearance and secure retention before use. Original design by John Rijos (VWrijos), licensed CC BY; attribution is required and the source marks commercial use as allowed.

Fits A4 · B5

Functional rear speaker adapter ring for the Audi A4 B5 (1994-2001). It adapts the stock rear speaker location and mounting holes to a standard 6.5-inch speaker; the source identifies Kicker 6.5-inch hole spacing, reports PLA test prints and vibration, and advises flipping the part upside down in the slicer to avoid supports. Verify speaker fit, depth, clearance, fastening, vibration isolation, and material suitability before use.

Fits A4 · B5

Vehicle-specific bracket for positioning a phone in the Audi Q8 wireless-charger area and preventing movement. The creator describes an iPhone 14 Pro fit and says the design can be modified in Tinkercad for other phones. Original design by john Dean (Jdeano12), Thingiverse thing:5812325, licensed CC BY; attribution is required and commercial reuse is allowed. The source recommends PETG or ASA, 20-30% infill, and verifying supports in a slicer. This is a custom accessory, not an OEM replacement; verify fit and vehicle safety before use.

Fits Q8 · Q8

Single-piece phone cradle for an Apple iPhone XS Max that seats in the Audi Q5 8R center-console wedge opening and provides a cable-routing channel while restoring the cupholder. The source calls for supports and recommends PETG or ASA with 20-30% infill; verify phone/case clearance, print strength, retention, and unobstructed access to vehicle controls before use.

Fits Q5 · 8R

Fitted center-console storage-tray insert/mat with an Audi-ring recess pattern, identified by the source for Audi S5 B9/F5 center-console fitment. The source attributes the original design to Phil Perry (Brummephil), describes it as a remix of JGutz20.mn’s Audi B9 center mat, and recommends PETG or ASA for durability and heat resistance. Verify trim level, dimensions, installation, and cabin heat exposure before printing or use.

Fits A5 · F5

3D-printable front camera mount for the RS-style aftermarket grille sold by German Car Accessories in 2020, documented for the Audi A5/S5 B9 (F5) and specifically listed for a 2020 Audi A5. The design angles the camera toward the original Audi camera angle and clears grille elements for a 180-degree view; the source states that it uses the original Audi screws and needs no additional hardware.

Fits A5 · F5

3D-printable center-console cup holder designed for Audi A6 C5 vehicles (1997-2004). The source shows a physical print installed beside the center console/gear selector and recommends PETG or ASA for durability; verify supports, fit, and slicer orientation before printing.

Fits A6 · C5

Direct-replacement trunk grocery-bag hook for the Audi A4 B8 Avant (generation 1777, 2007-2015). The source provides two working STL variants; rev2 is described as having an improved hook that retains bags better. Print in a cabin-temperature-capable material, verify fit against the original mounting point, and use only for light grocery or shopping bags after confirming secure retention and clearance. Original source creator: Rota; original source license: Creative Commons Attribution-ShareAlike.

Fits A4 · B8

Two-piece replacement rear-seat fastening clip set with separate outer and inner clip STL files. The source identifies the part as Audi/VAG 4L0886373 for Audi A4/A4 Quattro/S4/S6 applications including A4 B8/8K model years 2008-2015. The source recommends PETG or ASA and 20-30% infill with 1.2-1.6 mm walls; verify fit, orientation, retention, and seat operation before use.

Fits A4 · B8

Full-size dashboard radio-cover frame for the Audi A4 B5 (1994-2001), intended to cover and finish the vehicle radio opening. This variant adds front curvature and differently rounded corners. The source recommends PETG or ASA for durability, 20-30% infill, and verifying supports in the slicer.

Fits A4 · B5