Find your next part.

Phone holder for the shared dashboard cupholder slot; this version fits the 69 mm-wide slot and permits a USB charging connection.

Fits 911 · 996

Tapered installation tool that expands the PTFE piston seal and centers itself in the counterbore of the differential-lock cylinder piston.

Fits 911 · 964

Replacement ramp/clip that pushes down the sunroof wind deflector. The creator fitted the revised design and reported that it works correctly.

Fits 911 · 964

Gauge for setting the stepped brake-caliper piston face to 20 degrees on standard ATE calipers.

Fits 911 · Original (901/911)

Center mounting spacer that bridges the different lower profile created by a GT3-style front-bumper conversion and secures the existing front undertray. Its washer section can be retained or removed to adjust the mounting stack.

Fits 911 · 997

Three-part MagSafe phone holder that clips near the glove-box compartment on left-hand-drive interiors. Its position keeps the holder away from the gear lever and leather trim. It accepts a 46 mm-inner/54 mm-outer MagSafe-style magnet ring and the printed parts are joined with super glue.

Fits 911 · 991 · Boxster · 981 · Boxster · 982 (718 Boxster) +2

Replacement for the upper square CD-case storage unit in the dashboard, with a top cable-routing port for a USB/Bluetooth module. The creator printed it in resin and reports good fit.

Fits 911 · 996 · Boxster · 986

Left and right interior door-handle shells that convert the 997 door release to a GT3-style fabric pull strap. The archive includes a combined pair and strengthened separate left/right versions.

Fits 911 · 997

Left- and right-side frames for fitting nearly any 4x6 speaker behind the factory HiFi grilles while retaining the stock grille appearance.

Fits 911 · 993

Two-piece glove-box CD-holder replacement that mounts two USB ports and provides a pull-out tray for SIM-card access. It assembles with three M3 screws; the updated drawer includes a retaining screw.

Fits 911 · 997

Two-piece offset front license-plate mount comprising a curved plate bracket and screw-in tow-eye adapter. The adapter is bored for through-bolt reinforcement; the creator describes the shorter adapter as 78 mm long and suggests an approximately 85 mm M10 bolt.

Fits 911 · 997 · Boxster · 986

Protective installation cap that covers crankcase through-bolt threads so an O-ring is not sliced while being installed. The creator designed it during a 914-6/911T engine rebuild and revised the shape for improved printing.

Fits 911 · Original (901/911) · 914 · 914

Replacement shaft for the instrument-cluster trip and dimmer controls, measured from an OEM stalk. The creator recommends resin or ABS for resolution and heat resistance and notes that sanding may be needed for a close fit.

Fits 911 · 996 · Boxster · 986

Two-piece bracket that mounts a remote clutch bleed-screw assembly to the fan shroud. It is sized for a -3 AN bulkhead mount accepting a 3/8-24 bleeder screw and uses a removable end plate so the clutch line can be slid into place without disconnecting it.

Fits 911 · 993

Replacement collar stop for the hand-throttle rod, upgraded with two M3 set-screw holes that must be tapped after printing.

Fits 911 · Original (901/911)

Center-console tray remix for an iPhone 13 Pro and Anker 15W PowerWave Alloy charging pad, with added phone-positioning blocks and a lower cutout to clear the flip-up cover. It installs after removing the factory rubber liner.

Fits 911 · 991 · Boxster · 981 · Cayman · 981

Passenger/right headlight-washer cover with tabs and a companion jig used to heat-form the cover to the compound curve against the headlight housing.

Fits 911 · 996

Support clip for the 997 front-bumper mesh and slats. The supplied version 2 STL is smaller and more concealed than the photographed version 1; use 3 mm cable ties and two clips per side.

Fits 911 · 997

Replacement centre dashboard air vent recreated after the original in a 1976 Porsche 911 cracked. The creator reports that the ABS print fit perfectly and provides plain and brim-supported STL variants.

Fits 911 · G Model

Replacement flap for the fresh-air blower housing. The creator used a 4 mm foam-rubber seal and PETG for the heat encountered during cabin heating.

Fits 911 · G Model

Printable camshaft holding-down tool for early five-chain engines in the Boxster 986 and 911 996. The tool holds the camshafts during cylinder-head-cover removal and reassembly.

Fits 911 · 996 · Boxster · 986

Full-size 15.25-inch template for cutting replacement side-section stone-guard film, modeled for the 997 generation.

Fits 911 · 997

Adapters for 4-inch door and rear midrange drivers plus a two-piece Dynaudio MD-102 tweeter mount. The source covers Dayton Audio RS100/RS100P and Dynaudio E430 midranges; the tweeter mount requires Burmester grilles or modified Bose/SPP grilles and its two pieces are bonded before installation.

Fits 911 · 991

Printable replacement for the break-prone front-seat backrest release control button, modeled from the shared latch style used across the listed seat applications.

Fits 911 · G Model · 911 · 964 · 911 · 993 +4