car3dparts.

The parts catalog

Find your next part.

Find your fit. Download a free file or choose a maker to print and ship your part.

Reset

65 matching parts

Free files. Made for your car.
AC Vent Louvre Repair SetC3D–02553
Land RoverDashboard & controls

AC Vent Louvre Repair Set

Four-piece replacement repair set for the air-conditioning louvre assembly in a 1995 Land Rover Defender 300 Tdi (1994-1998), comprising the louvre, outer frame, alignment strip, and louvre clip rail. The louvre-fit holes require drilling to 2.5 mm; the louvre requires supports and the other components print without supports. Verify the exact AC vent variant, hole size, retention, louvre movement, and cabin-heat material suitability before installation. This should also fit other pre-puma/td4 Defenders

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Washer-Reservoir CapC3D–00185
Land RoverWipers & washers

Washer-Reservoir Cap

Replacement windscreen-washer reservoir cap with retaining-ring eyelet, spill-reducing internal lips, and a 0.4 mm vent hole.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Adapter for Discovery 2 Cruise Control switchC3D–00014
Land RoverDashboard & controls

Adapter for Discovery 2 Cruise Control switch

Adaptor to fit Discovery 2 Cruise Control switch to Defender td5. Quote from SimonRafferty: "It's very easy to add cruise control to any Td5 Land Rover Defender just by adding a couple of wires to the ECU and connecting them to a switch. (search on line for details) Unfortunately, there are no nice looking switches. My solution was to fit a switch from a Td5 Discovery 2 - and print this adaptor so it can easily screw on to the steering column. This is version 2 which is a much better fit and prints in one piece. Use higher temperature filament such as PETG or PAHT - otherwise it will melt in the sun. That's how come V2 came to be! Insert a couple of M4 Nuts into the slots provided, then attach the switch with 2 x M4 x 10mm screws"

Fits Defender · Td5

Brake Pipe ClipC3D–00012
Land RoverSteering, suspension & brakes

Brake Pipe Clip

Clip to hold brake pipes to chassis for Defender TD5. It fits into existing 7mmØ holes in chassis and holds a 5mmØ brake pipe secured by a 4.7mm*1.3mm nylon cable tie. It's designed to be forced into the chassis with a hammer and strongly hold the brake pipe even without beeing secured by the cable tie, but be aware that brake pipes are quite sensible parts of a vehicle and may result to your death if not secured appropriately. Use this part at your own risk and check conditions of the brake pipe clip regularly.

Fits Defender · Td5

C3D–00168
Land RoverSteering, suspension & brakes

Rear-Tub Chassis Shims

Eleven thickness variants of the isolating shim fitted between the chassis brackets and rear tub to separate dissimilar metals.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +5

Switch BlankC3D–02552
Land RoverDashboard & controls

Switch Blank

Replacement blanking plate for unused dashboard switch openings in the Land Rover Defender TD5 (1998-2005). It fills a dashboard opening where a switch is not fitted. Verify the exact dashboard aperture, dimensions, retention, and clearance before installation. PETG is the specified printing material; support is specified for printing.

Fits Defender · Td5

Upper Dashboard PanelC3D–02551
Land RoverDashboard & controls

Upper Dashboard Panel

Full-size upper dashboard panel for the Land Rover Defender Td5 (1998–2005), replacing the upper dashboard top/facia component across the instrument-panel area. Verify VIN and windscreen/vent variant, drive side, demister and fastener interfaces, dimensions, clearances, and material/print strength before installation.

Fits Defender · Td5

Softtop Seatbelt bar mountingC3D–02540
Land RoverDoors, bonnet, boot & bed hardware

Softtop Seatbelt bar mounting

If you mount the MRC7354 "Soft Top Front Seat Belt Bar For Land Rover Defender / Series" the tube do not fit very well the the capping. This part gives it a nice an stable connection. Needs tu be drilled trough after mounting fpr a tight fit. Drill 8 mm oder 5/16 "

Fits Defender · 200 Tdi · Defender · 300 Tdi · Series · 2 +2