car3dparts.

The parts catalog

Find your next part.

Find your fit. Download a free file or choose a maker to print and ship your part.

Reset

32 matching parts

Free files. Made for your car.
Sensor-Connector Locking PinC3D–01588
MercedesEngine-bay electrical & sensors

Sensor-Connector Locking Pin

Replacement 4 mm plastic locking pin for electrical sensor connectors and the Stromberg 175 carburettor valve connector. The creator demonstrates the printed pin with the original sensor fittings. Match the connector body and pin diameter exactly, use engine-bay heat- and fuel-resistant material, route wiring without strain and confirm the connector cannot loosen or short before operating the engine.

Fits W123 Series · W123 / S123 / C123

Climate-Control Trim SubstrateC3D–01582
MercedesDashboard & controls

Climate-Control Trim Substrate

Replacement substrate for the climate-control wood trim, demonstrated on a 1982 300D sedan. The creator warns that control-panel layouts vary between models and instructs users to compare the two rear locating pins and panel shape before printing; a separate wood veneer is required. Restrict use to the matching control layout, keep adhesive away from controls and wiring, and confirm every control moves freely after installation.

Fits W123 Series · W123 / S123 / C123

Rear Speaker Grille for Visaton FR 13C3D–01580
MercedesCabin trim, cargo & roof

Rear Speaker Grille for Visaton FR 13

Replacement rear-deck speaker grille for a Visaton FR 13 speaker. The creator physically tested the FR version; separate FX/PX variants were explicitly untested and are not included. Use cabin-heat-resistant material, secure the speaker independently with appropriate hardware and confirm the grille cannot become loose or interfere with rear visibility.

Fits W123 Series · W123 / S123 / C123

Tailgate Cargo-Cover ClipC3D–01576
MercedesCabin trim, cargo & roof

Tailgate Cargo-Cover Clip

Replacement tailgate clip for the retractable cargo cover on 300 TD/TE estate cars. Fitment is limited to the estate body included in this generation. Compare the mating profile, use cabin-heat-resistant material and confirm the cargo cover latches and releases without loading the tailgate trim. Only the creator's loose-part source photograph is included; the unrelated credited vehicle photograph is retained as evidence but not uploaded.

Fits W123 Series · W123 / S123 / C123

Heater-Control Knob BezelC3D–01572
MercedesDashboard & controls

Heater-Control Knob Bezel

Replacement bezel for the three rotary heater-control knobs. The creator modelled it after all three original bezels on their car had broken, and the source image shows the physical component. Use heat-resistant cabin material, compare the shaft and surrounding control face, and confirm each heater control turns through its full range without rubbing.

Fits W123 Series · W123 / S123 / C123

Selector-Linkage BushingC3D–01571
MercedesTransmission & drivetrain

Selector-Linkage Bushing

Replacement automatic gear-selector linkage bushing printed for a degraded original on a 123-series car. The creator shows the part at the linkage and notes that a 1/4-inch E-clip can replace a missing retaining clip. Use a wear-resistant material, retain the linkage securely, then verify every selector position, positive Park engagement and neutral-start behavior with the parking brake applied before driving; stop use if the linkage binds or develops play.

Fits W123 Series · W123 / S123 / C123

Lamp Retaining-Nut SetC3D–01570
MercedesExterior lighting, cameras & sensors

Lamp Retaining-Nut Set

Two sizes of replacement plastic retaining nut copied from the headlamp, indicator and rear-lamp hardware on a US-market 123-series car. The source does not define every position, so compare the original nut, thread, diameter and lamp location before choosing a size. Use weather- and heat-resistant material, tighten only enough to retain the lamp and recheck lamp alignment and sealing.

Fits W123 Series · W123 / S123 / C123

Bonnet-Latch Pull HandleC3D–01569
MercedesDoors, bonnet, boot & bed hardware

Bonnet-Latch Pull Handle

Replacement pull handle for the bonnet release latch. The creator designed it for 123-series cars, printed it successfully, warm-formed the slight original curve and drilled the metal-pin hole after printing. Shape only while warm, retain the original metal pin, verify full latch travel and confirm both primary and safety latches engage before road use. The creator only says it may fit later 124-series cars, so no cross-fitment is assigned.

Fits W123 Series · W123 / S123 / C123