Find your next part.

Workshop socket for removing and installing the radio-antenna retaining nut.

Fits Land Cruiser · 80 Series · Lexus LX · 450

Workshop socket for adjusting the differential side-bearing nut, modelled for a 1991 vehicle.

Fits Land Cruiser · 80 Series

Bracket for mounting a 2016 Elinz FHD dashcam at the passenger sun-visor fixing point, reusing the original visor screw.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Air-intake vent that replaces the removable seat-box floor grommet when fitting a diesel night heater. The creator secured it with marine sealant.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Workshop mandrel for centring the clutch plate during assembly. Confirm the spigot and spline diameters against the gearbox input shaft and clutch before use.

Fits Series · 2 · Series · 2A · Series · 3

Replacement quarter-turn retaining clip for the rear tow-hitch cover.

Fits Range Rover Sport · L320

Replacement receiver that grips the quarter-turn plastic screw securing the rear tow-bar cover.

Fits Discovery · 3 · Discovery · 4

Wheel-centre reference tool that holds a tape measure at the true hub centre during suspension-height calibration.

Fits Discovery · 3

Four-part clamp mount for attaching a Salora CDC100-style dashcam to the interior mirror. Short and tall ball-arm options are included, together with the mirror clamp and retaining nut.

Fits Freelander · 1

Replacement threaded carpet retainer.

Fits Freelander · 1

Replacement driven gear for a window-regulator motor mechanism.

Fits Freelander · 1

Dashboard surround for fitting a protruding double-DIN navigation head unit without cutting the original dash trim. PETG is recommended because PLA can deform in a hot cabin.

Fits Discovery · 1

Two-part eyelet mount that clamps around a factory roof rail using common M8 hardware. The source recommends PETG, 20% infill, doubled infill lines, and three walls. Use only for light-duty restraint and never as a rated recovery or lifting point.

Fits Discovery · 3 · Discovery · 4

Replacement door-panel/card retainer stud for the Range Rover P38 and Discovery 2. Corresponds to genuine Land Rover MWC9134

Fits Range Rover · P38

Reinforced replacement bonnet-release lever for a right-hand-drive Range Rover P38. Corresponds to Land Rover FSC10004

Fits Range Rover · P38

Replacement protective sleeve for the Range Rover Classic heated rear-window cables, Land Rover part 589818. The source author changed the original round section to a square section and tuned the curvature for fit. PETG or nylon is preferable to brittle PLA. LR3DParts converted the original ASCII STL to binary STL without changing its geometry for upload compatibility.

Fits Range Rover · Classic

Fuse cover designed for an approximately 1993 Range Rover Classic 200Tdi. Uses one M3 x 25 screw. This is the screw-retained alternative to the standard fuse-box cover.

Fits Range Rover · Classic

Replacement fuse-box cover for the full-size Range Rover Classic.

Fits Range Rover · Classic

Fixes the plastic tabs on the A Pillar that usually break when trying to remove the trim for upgrades like UHF installs

Fits Discovery · 1

Replacement blanking plate for unused dashboard switch openings in the Land Rover Defender TD5 (1998-2005). It fills a dashboard opening where a switch is not fitted. Verify the exact dashboard aperture, dimensions, retention, and clearance before installation. PETG is the specified printing material; support is specified for printing.

Fits Defender · Td5

This 3D-printed seat lever cover is designed as a replacement cover for the seat-folding lever mechanism used for the 6th and 7th passenger seats. It provides a neat, durable solution when the original plastic cover is damaged, missing or worn.

Fits Discovery · 4

Clip-on cover that blocks the light gap around the sun-visor retaining point while preserving normal visor operation. The creator explicitly identifies 2018-and-later Alfa Romeo Giulia and Stelvio fitment and recommends PETG, ABS or ASA for summer cabin heat.

Fits Giulia · Tipo 952 · Stelvio · Tipo 949

Storage shelf fitted ahead of the gear lever above the DNA selector area on 2013-on vehicles. The creator shows it installed and reports printing without supports with adequate cooling. Keep the selector and adjacent controls fully accessible.

Fits Giulietta · Tipo 940

Replacement plug that covers an enlarged screw hole in the interior pillar trim.

Fits 944 · 944