Find your next part.

Cup-holder stand sized for an iPhone 13 Pro or iPhone X and designed around a BENKS Magnetic Wireless Charger Cooler Radiator for wireless charging and thermoelectric cooling. The creator specifies a USB-C car adapter rated at least 20 W and uses 3M VHB tape to take up cup-holder clearance.

Fits 911 · 992

Plastic latching receptacle that fits into the front luggage-compartment battery bracket and receives the quarter-turn battery-cover screw plug.

Fits 911 · 996 · Boxster · 987

Cup-shaped storage inserts for the shared C-Class, E-Class, and GLC cupholder geometry, supplied with and without a light window and with optional coin storage. Only the non-ashtray files are included; the ember-extinguisher variants are intentionally withheld. The creator used flame-retardant ABS. Select the correct lighting version, keep the original light unobstructed, and use only for coins or other small non-hot items.

Fits C-Class · W205 / S205 / C205 / A205 · E-Class · W213 / S213 / C238 / A238 · GLK / GLC · X253 / C253

Screen-hook phone-mount bar with a 14 mm ball, designed around an MPOW wireless charger. The author supplies separate right-hand-drive and mirrored left-hand-drive files and shows both the bare part and installed phone. Bend only as required for installation behind the screen, verify the correct steering-side file, protect dashboard surfaces, and confirm the mount cannot obscure instruments, loosen, or contact controls.

Fits C-Class · W205 / S205 / C205 / A205

Phone-mount adapter designed for the two center dashboard vents and used by the creator with a uGreen magnetic mount. The source identifies exact hatchback fitment and provides the printable adapter; the mating phone mount is not included. Print in ABS as specified by the creator, verify that the adapter does not crack or loosen, maintain airflow, and position the phone so it cannot obstruct the road view, controls, display, or airbags. The source GNU GPL v2 licence is represented by the API’s other licence value.

Fits A-Class · W176

Single-piece cargo lashing ring designed for the roadster trunk and fixed beneath an existing trunk screw. The creator explicitly identifies R172 fitment and shows the ring installed. It is only for restraining small, light items while driving; the creator states that it is not made for high forces. Do not use it for heavy cargo, occupant restraint, recovery, lifting, towing, or any safety-critical load. Confirm that the original fastener retains full thread engagement, keep the ring clear of roof and trunk mechanisms, and remove it if the print cracks, loosens, or deforms.

Fits SLK / SLC · R172

Replacement recess surrounding a cargo-floor lashing eye. The creator explicitly identifies 906-series fitment, shows the part installed around the original eye, and recommends PETG or ABS instead of PLA because the original recesses rust and replacements are costly. This print is a non-load-bearing surround only: retain the original metal eye and certified anchor hardware, inspect corrosion beneath it, preserve full anchor movement and clamping, and never transfer cargo load through the printed recess.

Fits Sprinter · W906

Press-fit dock for the lower centre-console storage shelf, with a large-phone slot and three pen holes. The creator identifies 906-series fitment and supplies both the OpenSCAD source and printable mesh plus an installed source photograph, but gives no body, market or steering-side expansion. Confirm the shelf profile and phone size before printing, use cabin-heat-resistant material, keep the device and charging cable clear of controls, and verify secure retention under braking.

Fits Sprinter · W906

Dashboard phone-mount adapter designed by the creator for the GL 450 X164 and shown physically installed between the two center vents. The supplied single STL has a 17 mm ball for a compatible phone cradle. The source does not state model year, pre- or post-facelift fitment, market, steering side, dashboard option, attachment method, material, print settings, device weight, or retention testing. Compare the center-vent surround before printing, use a cabin-heat-resistant material, protect the original trim, keep the mount clear of vents, controls and sight lines, and verify that the adapter and cradle remain secure under braking before road use. Do not place a device where it could interfere with an airbag.

Fits GL / GLS · X164

Left- and right-hand caps that close the openings at the tops of the front-door B-pillar trims. The creator modeled substitutes from a deteriorating original on an ML350, recommends ABS, ASA or PETG rather than PLA for sun exposure, and advises a test fit with light filing if necessary plus a small amount of clear adhesive behind the cap. EPC evidence found complete left/right trim mouldings, not these printed child caps, so no parent assembly number is assigned.

Fits M-Class / GLE · W164

Three-file magnetic phone-mount body designed specifically to clip into the R171 center console without glue, drilling, or permanent vehicle modification. The source includes a one-piece model and a split base/top alternative; add a generic magnetic phone pad to the upper surface with adhesive. Creator photographs show the printed mount installed beside the selector in left-hand-drive vehicles. Use only the one-piece file or the two split files as a complete alternative, print in a cabin-temperature-capable material, confirm the mount cannot contact the selector or controls, route charging cables clear of moving controls, and remove it if it loosens or obstructs operation.

Fits SLK / SLC · R171

Flexible 74 mm replacement cap for the windscreen-washer reservoir. The creator measured the original, recommends TPU and notes that a 98% scale may improve fit; source photographs show it installed. Verify the reservoir neck diameter, print in washer-fluid-, heat- and weather-resistant flexible material, and confirm the cap seats securely without obstructing filling or venting.

Fits Sprinter · W901–W905 · Sprinter · W906 · Vito / Viano / V-Class · W639

Trim cover for the upper seat-belt height-adjuster anchor. Source photographs show the printed cover installed over the factory adjuster; it is cosmetic and must not carry belt load. Use tough cabin-heat-resistant material, preserve unobstructed adjuster travel, never cover damage or alter the belt, anchor or mechanism, and confirm the belt retracts, adjusts and locks normally after fitting.

Fits Vito / Viano / V-Class · W639

Replacement pull handle for the sunroof shade. The creator designed it for the CLS C219 and explicitly reports confirmed E-Class fitment; source images show the physical handle installed. No other roof or trim variant is inferred.

Fits E-Class · W211 / S211

Storage tray that installs in place of the factory CD changer. The creator specifies ASA or ABS, four walls, five top and bottom layers, and 13% infill.

Fits E-Class · W211 / S211

Replacement tab for the rear center-console air vent. The author states that it fits this vent position only and that other air-vent locations were not tested; surface finishing and paint may be needed.

Fits E-Class · W211 / S211

Strengthened replacement clip for the glovebox ballpoint-pen holder. The creator explicitly lists W169, W203, W204, W209, W212 and W245 fitment, shows the part installed and recommends ABS for cabin heat; W245 is absent from the live taxonomy. No body, market or production-break split is stated, so compare the original clip and glovebox recess before printing, fit without damaging the lid and confirm the pen and clip cannot detach into the footwell.

Fits A-Class · W169 · C-Class · W203 / S203 / CL203 · C-Class · W204 / S204 / C204 +2

Standard and reverse-camera variants of a registration-plate light housing, designed to compress the reused approximately 2 mm gasket against the body. The creator used nylon and states the source reference as 'A 203 802 07 56'; independent Mercedes and PartSouq evidence identifies A2038200756 as the complete CL203 lamp housing, but it is not assigned because this canonical source includes a modified camera variant and the creator's number is transposed. Compare the original housing, gasket, connector and body style, use weather- and heat-resistant material, seal against water and verify illumination, camera view and boot-lid operation.

Fits C-Class · W203 / S203 / CL203

Two author variants of the left/right rear-bumper opening cover for the pre-facelift (phase 1) vehicle. Source photographs show loose printed covers and installed results. Fitment is not established for facelift bumpers or alternative bumper packages; compare the opening, tabs and side before printing.

Fits M-Class / GLE · W163

Replacement windshield-washer-fluid reservoir cap proven by the creator on a 1999 first-generation SUV. The source reports that the original cap crumbles with age and that the replacement was printed successfully in dual-colour ABS; the colour change was made 1 mm into the print. Verify the cap profile against the vehicle before installation.

Fits M-Class / GLE · W163

Rear-position exterior cover for the side-skirt jacking opening, published for the CLK 208-series and shown installed on the creator's photographed coupe trim. Print vertically with supports and three wall lines to strengthen the hooks, using ABS or a similarly suitable material as the creator recommends. The source does not identify side, facelift, AMG/standard trim, option code or an exact molded number; compare the original opening and retainers before use. No OEM number is inferred from the cover's location.

Fits CLK · C208 / A208

Replacement linkage rod for a dashboard air vent, explicitly identified for 901-series vans. Source photographs show the small printed rods and the matching vent assembly, but no steering-side or vent-position split is stated. Compare the original linkage length, pins and grille geometry, use tough cabin-heat-resistant material and verify every vane moves together through full travel without binding or detaching.

Fits Sprinter · W901–W905

Replacement handle for the climate-control panel. The creator states exact 210-series use and provides four CAD views plus a printable part and an editing variant, but no installed photograph or detailed trim/market split. Compare the original handle, shaft and panel before printing, use cabin-heat-resistant material, keep the control mechanism free of debris, and verify full smooth travel and the correct setting indication after installation.

Fits E-Class · W210 / S210

Front-door speaker adapter for shallow 160–170 mm drivers; the creator used a 50 mm-deep Pioneer driver. The supplied geometry is for the right/passenger side and must be mirrored for the left/driver side. The source specifies no supports, 0.3 mm layers, 0.8 mm walls and 30% infill, and requires drilling a small wire hole and sealing it after routing. Match the speaker basket and door mounting pattern, use cabin-heat- and vibration-resistant material, protect wiring, seal the wire opening and confirm both adapter and driver remain secure without interfering with glass or trim.

Fits C-Class · W202 / S202