Find your next part.

Rear-position exterior cover for the side-skirt jacking opening, published for the CLK 208-series and shown installed on the creator's photographed coupe trim. Print vertically with supports and three wall lines to strengthen the hooks, using ABS or a similarly suitable material as the creator recommends. The source does not identify side, facelift, AMG/standard trim, option code or an exact molded number; compare the original opening and retainers before use. No OEM number is inferred from the cover's location.

Fits CLK · C208 / A208

Replacement linkage rod for a dashboard air vent, explicitly identified for 901-series vans. Source photographs show the small printed rods and the matching vent assembly, but no steering-side or vent-position split is stated. Compare the original linkage length, pins and grille geometry, use tough cabin-heat-resistant material and verify every vane moves together through full travel without binding or detaching.

Fits Sprinter · W901–W905

Replacement handle for the climate-control panel. The creator states exact 210-series use and provides four CAD views plus a printable part and an editing variant, but no installed photograph or detailed trim/market split. Compare the original handle, shaft and panel before printing, use cabin-heat-resistant material, keep the control mechanism free of debris, and verify full smooth travel and the correct setting indication after installation.

Fits E-Class · W210 / S210

Front-door speaker adapter for shallow 160–170 mm drivers; the creator used a 50 mm-deep Pioneer driver. The supplied geometry is for the right/passenger side and must be mirrored for the left/driver side. The source specifies no supports, 0.3 mm layers, 0.8 mm walls and 30% infill, and requires drilling a small wire hole and sealing it after routing. Match the speaker basket and door mounting pattern, use cabin-heat- and vibration-resistant material, protect wiring, seal the wire opening and confirm both adapter and driver remain secure without interfering with glass or trim.

Fits C-Class · W202 / S202

Replacement sliding clip that retains the rear-lamp bulb-carrier assembly. The creator removed the reflector, installed the printed clip, lubricated its sliding faces and reports that it holds the carrier in place. The stated 1298201577, 1298200577 and 1298200677 numbers identify complete lamp assemblies, not this printed child, so they are not assigned. Print with the circular opening toward the bed, use ABS or another heat- and weather-resistant material, verify smooth clip travel and carrier retention, then test every rear lamp before driving.

Fits SL · R129

Replacement plastic support panel beneath the wooden centre-console switch trim. The creator reports that the design works but may require sanding. Compare the switch layout and console version before printing, use cabin-heat-resistant material, deburr all openings, and confirm switches, wiring and the selector remain unobstructed.

Fits 190 Series · W201

Replacement driver-side dashboard vent surround, supplied as both a complete model and a two-piece version for easier printing. The creator reports that it fitted but was not fully refined, warns that PLA deformed in summer heat, and says to mirror the part for left-hand-drive use. The complete STL appears about 25.4 times smaller than the split files when interpreted as millimetres, so verify source units and final dimensions in the slicer. Confirm steering side and vent geometry, print in heat-resistant material, and verify free vent-slider movement.

Fits 190 Series · W201

Replacement cap for a broken cabin-blower control switch, modeled from the original for a 190-series interior. The source provides comparison imagery but no long-term validation details. Compare the switch shaft and detents, use tough cabin-heat-resistant material, and verify every blower position operates and the cap cannot bind against the panel.

Fits 190 Series · W201

Replacement gear for the single-arm windscreen-wiper mechanism. The creator documents the dismantled mechanism, press-fitting the gear after heating the splined shaft, and specifies nylon at 100% infill. Treat this as a mechanism repair: compare tooth count and shaft profile, preserve alignment and lubrication, and bench-test full travel, parking and stall behavior before wet-road use.

Fits 190 Series · W201

Replacement 12-tooth drive pinion demonstrated in an Australian-compliance 1989 560 SEC instrument cluster. The creator printed, fitted and updated the gear profile after road use, and reports continued odometer operation. Fitment is restricted to a matching 12-tooth cluster; do not assume every 126-series speedometer uses it. Support the rotor shaft during press-fitting, preserve end float, have any desoldering performed competently, and verify accurate speed and distance readings before road use.

Fits S-Class · W126 / C126

Replacement rubber buffer insert for a door striker, explicitly designed for the 126-series. The printable is only the sacrificial insert, not the metal striker or latch assembly. The creator specifies printing on its side with build-plate-only support and 100% infill. Use durable flexible material, compare the original insert and striker geometry, and confirm both primary and secondary door-latch engagement before driving.

Fits S-Class · W126 / C126

Flexible grommet sealing the windscreen-washer pump to the reservoir on a 300D. The creator specifies flexible filament and 100% infill. Clean the reservoir opening, compare both pump and tank diameters, use washer-fluid-compatible TPU and confirm a leak-free seal before closing the bonnet.

Fits W123 Series · W123 / S123 / C123

Modified rear-deck grille for Rockford Fosgate R1525 5.25-inch speakers, derived from the creator's credited earlier grille design. The source specifies ABS or another high-temperature material to avoid cabin-heat deformation. Secure the speaker independently, verify grille retention and keep the installation clear of rear-window visibility and parcel-shelf hardware.

Fits W123 Series · W123 / S123 / C123

Replacement headlamp mounting nut shown beside the original physical component. Compare the thread, diameter and lamp position before use, print in heat- and weather-resistant material, tighten only to the original retention load and verify headlamp aim and stability after installation.

Fits W123 Series · W123 / S123 / C123

Replacement plastic locating pin for the wooden switch panel in the centre console, demonstrated on 240D and 300D cars. The creator provides a central hole for an optional cut-down steel nail bonded with adhesive to reinforce the shaft. Keep metal reinforcement fully encapsulated and clear of wiring, use heat-resistant material, and confirm the panel is retained without stressing the veneer or switches.

Fits W123 Series · W123 / S123 / C123

Replacement door-seal clip measured directly from an original coupé component. The creator tested prototypes in PLA and final parts in ASA/PETG, recommends nylon for durability and specifies horizontal print orientation for strength. Fitment is limited to the coupé body. Compare the original clip, deburr all edges and confirm the seal seats continuously without preventing safe door latching. The source references A0009871015, but no exact independent EPC child-component record was recovered, so no OEM number is assigned.

Fits W123 Series · W123 / S123 / C123

Flexible replacement cap for the windscreen-washer reservoir, printed by the creator in TPU without supports. Compare the filler-neck diameter, print in fluid-tolerant flexible material, keep fragments out of the reservoir and confirm the cap seals without obstructing the pump pickup or hoses.

Fits W123 Series · W123 / S123 / C123

Replacement plug-style retaining clip for the windscreen-wiper vent grille. The creator checked the dimensions on a 123-series car and notes that minor sanding may be needed because the design substitutes a plug action for the original push-through clip. Use weather-resistant material, fit without cracking the grille and confirm every clip remains secure through wiper operation and water flow.

Fits W123 Series · W123 / S123 / C123

Protective cap for the windscreen-wiper shaft, explicitly shown on 240D, 300D and 300TD applications. Use UV- and weather-resistant material, verify clearance through the complete wiper sweep and ensure the cap cannot loosen onto the windscreen or cowl.

Fits W123 Series · W123 / S123 / C123

Flexible protective sleeve for wiring passing into a front door. The creator specifies 123-series driver or passenger doors, flexible filament, and an upward slicer orientation for the sealing-lip end. Route the wiring without tension, seat both ends fully, confirm the door closes without pinching the sleeve, and inspect periodically for abrasion or water ingress.

Fits W123 Series · W123 / S123 / C123

Blanking cover for an unused centre-console switch opening. The creator designed it on their own 123-series car and reports a perfect fit; the opening may also be used as the basis for a custom switch or charger. Compare the slot dimensions and console finish, keep clear of wiring and moving controls, and fuse any electrical accessory separately according to its manufacturer instructions.

Fits W123 Series · W123 / S123 / C123

Bolt-on replacement handle for broken manual seat-adjustment levers. The creator explicitly designed and photographed it for both 116-series and 123-series cars, states that it can be used at all four handle positions, and notes that side height adjusters accept one screw while the front adjusters use two. The demonstrated part was printed in PETG, sanded and buffed, then fastened through the surviving metal lever with screws and nuts. Remove only the remains of the failed grip, preserve the original lever, deburr all holes, use secure low-profile hardware, and confirm full adjustment and locking travel before driving.

Fits S-Class · W116 · W123 Series · W123 / S123 / C123

Replacement rocker cap for the electric-window switch. The creator modeled it after a broken original, reports that it fits, and recommends resin printing because ordinary FDM appearance and durability were unsatisfactory. Preserve the switch mechanism and contacts, confirm free return movement and electrical isolation, and stop using the part if it binds or softens in cabin heat.

Fits SL · R107

Replacement 8 mm dashboard screw cap, shown as a loose physical print beside its screw. The source identifies E85 fitment but no separately serviced BMW component number; do not force the cap, and verify colour, diameter and trim retention.

Fits Z4 · E85 / E86