Find your next part.

Two-gauge replacement for the BMW E36 centre vent. Only the physically printed and installed double-52 mm variant is retained from the source; its other untested variants are excluded. Confirm gauge depth, wiring, visibility and remaining demist airflow.

Fits 3 Series · E36

Replacement interior door-trim clip traced from the original and modified for strength. The source physically compares the printed clip with the original. Test one clip for panel alignment and removal before replacing the full set.

Fits 3 Series · E36

Replacement centre-vent insert measured from a BMW E36 323ti Compact and physically installed with a 52 mm gauge. It sacrifices vent airflow at that position; use cabin-heat-resistant material and verify gauge, wiring and dashboard clearance.

Fits 3 Series · E36

Contour spacer demonstrated with aftermarket side repeaters on BMW bodywork. The creator lists E36 from October 1996, E46 sedan/Touring, E60/E61, E81/E82/E87/E88 and E90–E93 applications. Test one side before mirroring and verify the repeater remains weather-sealed and positively retained.

Fits 1 Series · E81 / E82 / E87 / E88 · 3 Series · E36 · 3 Series · E46 +2

Replacement knob specifically for the late-model E30 manual sunroof crank, shown physically installed. Use cabin-heat-resistant material and verify that the crank turns and folds freely.

Fits 3 Series · E30

Replacement E30 electric window-lifter spacer for mechanisms through April 1988, reproduced from the original and physically installed. BMWFans confirms spacer 51331919541; power-window mechanisms only.

Fits 3 Series · E30

Replacement front-seat rail nut cap for early cars from September 1985 onward and late-model E30, copied from and physically compared with the original. BMWFans confirms covering cap 52101941999.

Fits 3 Series · E30

Replacement fastener for E30 front-seat side covers, copied from the original and physically compared. It supports stock, sport and Recaro seats; BMWFans confirms push-button 52101906933.

Fits 3 Series · E30

Snug-fitting flat cover for the E30 power-antenna opening. The creator reports it stays in place without extra fasteners; confirm the body opening, weather sealing and retention before road use.

Fits 3 Series · E30

Replacement side covers for BMW Reverse RDS, non-RDS, Bavaria and Business radios used in E30, E32, E34 and E36. The source shows physical fit and finish; BMWFans confirms covering cap 65126907823.

Fits 3 Series · E30 · 3 Series · E36 · 5 Series · E34 +1

Reinforced fastening repair for the E30 centre-side or B-pillar trim cover, copied from the original attachment and intended to be bonded to the broken cover. The creator-listed 51431933731/732 references are parent trim covers, so no OEM number is assigned.

Fits 3 Series · E30

Dimensioned replacement glovebox damper pin for BMW E21, E28, E30, E31, E34, E38, E39, E46 and E60/E61. The creator identifies BMW pin 51161828956 and shows the physical result installed. Verify damper eye and panel thickness before fitting.

Fits 3 Series · E21 · 3 Series · E30 · 3 Series · E46 +6

Short adapter ring that centers narrow energy-drink cans in the factory cup holder of BMW F45 Active Tourer and F46 Gran Tourer models. The creator physically tested the reduced-height ring and photographed it installed.

Fits 2 Series · F45 / F46 Active / Gran Tourer

Replacement hook that retains the cargo cover in position on the BMW F45 2 Series Active Tourer. Creator photographs show the physical hook installed; compare mounting orientation and clearances before fitting.

Fits 2 Series · F45 / F46 Active / Gran Tourer

Cup-holder insert for 330 ml beverage cans in BMW F22 and F87 interiors. The creator uses it in an F87 M2 and shows both the empty insert and a can seated in it. Print in PETG, ASA, ABS, or another cabin-temperature-resistant material and confirm the can remains stable without obstructing nearby controls.

Fits 2 Series · F22 / F23 / F87

Cup-holder phone stand with a Lightning-cable passage, documented by the creator for BMW F20 1 Series and F30/F31 3 Series interiors. The gallery shows the stand installed, holding phones, and routing the charge cable. Add a thin foam or rubber liner as suggested, use a heat-resistant cabin material, and confirm secure phone retention before driving.

Fits 1 Series · F20 / F21 · 3 Series · F30 / F31 / F34 / F80

Press-fit cover for the deteriorating climate-control rotary knob in a 2013 BMW F20 1 Series. The creator refined the fit through five iterations and shows the cover installed over the original knob. Use a cabin-temperature-resistant material and check that the control rotates without binding.

Fits 1 Series · F20 / F21

Two-piece replacement for the left dashboard air-vent position in a BMW E87, combining the vent housing with a round gauge/display holder. The creator's gallery shows the assembly installed in the vehicle. Confirm the instrument diameter and preserve safe driver visibility before installation.

Fits 1 Series · E81 / E82 / E87 / E88

Adapter for fitting an older Omix-Ada 11020.01-style rear-view mirror to the newer windshield frame in a 1981 Jeep CJ-7. The source documents the printed adapter and physical installation.

Fits CJ · CJ-7

Three factory-style windshield hood-block geometries measured from original parts and Willys master-parts documentation. Separate printable blocks cover CJ-2A, CJ-3A, and CJ-3B vehicles; two matching blocks are required per Jeep.

Fits CJ · CJ-2A · CJ · CJ-3A · CJ · CJ-3B

Console cupholder adapted specifically for Comanche MJ interiors with the parking brake on the floor. Two variants provide standard beverage wells, a small-can recess, and side slots for cards or change.

Fits Comanche · MJ

Replacement fuse-puller tool stored at the Grand Cherokee WJ and WG fuse panel. The source documents both the factory storage position and the printed replacement.

Fits Grand Cherokee · WJ / WG

Replacement interior hood-latch release handle developed for a 2001 Grand Cherokee WJ and WG after the factory handle broke.

Fits Grand Cherokee · WJ / WG

Replacement receptacle for the ball studs on 1999–2004 Grand Cherokee WJ and WG headlight housings. Three receptacles support each lamp while preserving adjustment movement.

Fits Grand Cherokee · WJ / WG