The parts catalog
Find your fit. Download a free file or choose a maker to print and ship your part.
2,661 matching parts
Free files. Made for your car.
C3D–00162Base-plate adapter for fitting GMC/Chevrolet pickup tie-down anchors to the cargo-area ceiling. Installation uses two 3/8 × 1.5-inch carriage bolts with washers and nuts.
Fits Defender · L663
C3D–00158Temporary reservoir cap for pressure-assisted brake bleeding. Inspect the print, seal, and hose connection carefully and use only low, controlled pressure.
Fits Series · 3
C3D–00152Replacement threaded button for the handbrake lever. The source recommends finishing the undersized bore with an M5 tap for a secure fit.
Fits Series · 2A · Series · 3
C3D–00151Replacement COLD–WARM heater control button. Compare the lever slot and lettering orientation with the original before printing and fitting.
Fits Series · 2 · Series · 2A · Series · 3
C3D–00146Three-part loadspace-light conversion comprising an installation template, switch panel, and blanking plate. Wiring polarity and switching differ between early and later vehicles, so verify the circuit before modification.
Fits Freelander · 2
C3D–00141Replacement internal gear set for a failed tailgate-lock actuator. Three printable variants are included
Fits Freelander · 2
C3D–00139Replacement cap for the windscreen-washer reservoir.
Fits Freelander · 2
C3D–00137Two-piece coin organiser for the centre-console area, comprising a main holder and lid.
Fits Freelander · 2
C3D–00132Replacement end piece for a longitudinal roof rail.
Fits Range Rover · L322
C3D–00123Replacement end cap for the passenger roof grab handle, measured from a 2000 four-door vehicle.
Fits Freelander · 1
C3D–00120No-drill rear-camera holder that replaces one number-plate-light position. Confirm camera dimensions, cable routing, and local lighting requirements before installation.
Fits Freelander · 1
C3D–00119Replacement bushing for the manual gear linkage above the gearbox, intended to reduce excess movement during gear selection. Use a durable, wear-resistant material and verify the linkage joint before fitting.
Fits Freelander · 1
C3D–00115Four-part fascia, side-bracket, and brace set for installing an aftermarket double-DIN stereo in the 2008 dashboard.
Fits Range Rover Sport · L320
C3D–00114Replacement air intake for a Webasto Thermo Top V fuel-burning heater when the original retaining legs have broken. Print with the legs downward and supports from the build plate.
Fits Discovery · 3 · Discovery · 4 · Range Rover Sport · L320
C3D–00105Two-part centre-console cup holder with an enlarged approximately 75 mm internal diameter and no phone pocket. Designed from a related holder and explicitly stated to fit this generation.
Fits Discovery · 1
C3D–00099Replacement cover for the window-switch panel on three-door vehicles. Confirm switch layout and panel dimensions before printing.
Fits Discovery · 1
C3D–00094Phone holder designed to sit in the front coin tray, sized around an iPhone 11 in an Apple case. Confirm phone and tray dimensions before printing and use a heat-resistant cabin material.
Fits Range Rover · L322
C3D–00090Replacement push clip for the front cowl and wiper-panel cover on 2002–2009 vehicles. Use a flexible, weather-resistant material and compare dimensions with an original clip before fitting.
Fits Range Rover · L322
C3D–00086Dashboard phone mount for fitting a Quad Lock interface in the Discovery 3/LR3 cabin. Confirm the mating interface and dashboard fit before final installation.
Fits Discovery · 3
C3D–00083Replacement quarter-turn screw for retaining the rear-bumper towbar access door when the towbar is not fitted. Print with high infill and confirm engagement before road use.
Fits Discovery · 3
C3D–00070Small friction-fit repair piece that restores the lower passenger cup-holder hinge after its moulded pins shear off. Print two
Fits Discovery · 3
C3D–00063Two-part replacement cover for the third-row seat release lever, with a separate pictogram insert.
Fits Discovery · 3
C3D–02684Fixes the plastic tabs on the A Pillar that usually break when trying to remove the trim for upgrades like UHF installs
Fits Discovery · 1
C3D–02682Replacement flexible cap for the windshield-washer fluid reservoir filler neck on the Ford Focus MK3 1.5 TDCi, covering the 2011–2018 third-generation application. It restores the removable cover over the washer-fluid tank opening; TPU is specified for the flexible printed part.
Fits Focus · Third generation