Find your next part.

Replacement interior door-handle trim bezel for BMW E30, E24, E28 and E23, physically printed and fitted. BMWFans confirms cover 51211876043. Print in a UV- and cabin-heat-resistant material.

Fits 3 Series · E30 · 5 Series · E28 · 6 Series · E24 +1

Two-part bracket and frame for installing Carling-style accessory switches in place of the factory ashtray.

Fits Discovery · 3

Clip Front Seat Belt Retainer For Land Rover Defender

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Scanned right-side F30/F31 headlight support bracket shown fitted in place by the creator. Use exterior-rated material and verify retention, weather sealing, lamp aim and washer operation before driving.

Fits 3 Series · F30 / F31 / F34 / F80

Multi-part dashboard housing, frame, gauge mount, button, adaptor, and support bracket for the BinOwl onboard-computer installation.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Replacement blanking button for an unused dashboard switch position. Two model variants are included

Fits Discovery · 1

Adapter plate that replaces the obsolete factory phone cradle while reusing its original dashboard bracket and screws, with variants for a Brodit MoveClip mounting pattern and alternate screen position. Source photographs show the bracket, plate and phones installed. Match the equipped cradle and screw lengths, use cabin-heat-resistant material, and confirm the device cannot obscure instruments, controls, airbags or the driver view.

Fits Vito / Viano / V-Class · W639

Two fit variants of a blanking plate for the 1998 dashboard ashtray opening.

Fits Defender · 300 Tdi · Defender · Td5

Clip-in dashboard-vent deflector that directs part of the demister airflow towards the side window. The creator positions it over the vent funnel, about 150 mm from the outer end.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Simplified 78 mm centre hub cap for Range Rover Classic alloy wheels. Prints without supports.

Fits Range Rover · Classic

Inner center-console bracket for the Land Rover Discovery 2 switch bank. It supports four window switches, two heated-seat switches, and the rear-window lockout switch, and is intended for the fully populated seven-switch console layout.

Fits Discovery · 2

Left and right replacement hinges for the rear parcel shelf. The original source supplies both handed files and a physical comparison image; a later credited remix explicitly identifies this original design as the W177 parcel-shelf hinge and retains the same interface while adding reinforcement. Print the original files on their flat sides at 0.16 mm, with four walls and no supports; the creator suggests fuzzy skin only on the four towers that enter the parcel shelf. A later source specifies PETG for this cabin/cargo application. Inspect layer adhesion and both pivots, confirm free movement, and avoid loading the shelf until both hinges are fully seated. No Mercedes number is assigned: A1776905400 identifies the complete parcel shelf, not either printed hinge child.

Fits A-Class · W177

Two-piece dual cup holder designed to insert into the centre-console cupholder while preserving access to the 12-volt socket, armrest and selector. The source supplies cup and stand STLs plus a CAD image but no container-size or crash-retention test. Use cabin-heat-resistant material, check console and selector clearance and test only with cold, closed containers before road use; confirm the assembly cannot detach or spill into controls under braking.

Fits C-Class · W203 / S203 / CL203

Three glue-in repair bases for the different upper, middle and lower clip positions on BMW E36 A-pillar trim. The source physically shows the damaged trim and provides position-specific geometry. Mark each original location and verify the trim remains secure around any curtain-free wiring or seals.

Fits 3 Series · E36

Replacement slider for the factory BMW wireless-charging cradle that increases usable phone length to approximately 168 mm. The creator documents F2x, F3x, F8x, and I01 cradle compatibility and shows the printed part installed and measured. Print in PETG, ASA, ABS, or another cabin-temperature-resistant material; verify latch engagement, charging operation, and secure phone retention before driving.

Fits 1 Series · F20 / F21 · 2 Series · F22 / F23 / F87 · 3 Series · F30 / F31 / F34 / F80 +2

Two-part centre-console organiser comprising a main tray and removable divider. Use a cabin-temperature-resistant material because PLA may soften in summer heat.

Fits Discovery · 3

Land Rover Discovery 1/2 window switch bezel. You need to print 4 pins

Fits Discovery · 1 · Discovery · 2

Front bumper end cap clip for Defender

Fits Defender · Puma

Bushing located at both ends of the rod connecting the wiper motor to the wipers. Print in plain nylon for best results. Video of install here: https://youtu.be/1ZTh9ZuZpTM?si=5zUaRD01rmpsLkAI

Fits Land Cruiser · 60 Series

Replacement retaining hook for the roller sunshade in a rear door. The creator modeled it for the fourth-generation X5, shows the printed clip next to the original, and documents it installed and holding the shade. The printed hook is intentionally slightly shorter than the original. BMW component 51 35 7 479 511 is catalogued for the G05 X5 and G06 X6 rear-door shade application, so both evidence-backed generations are linked. Fitment requires the rear side-window roller sunblind equipment; confirm door trim, shade and mounting geometry by VIN. Print in a heat-resistant automotive material and test smooth release and secure retention before road use.

Fits X5 · G05 / F95 · X6 · G06 / F96

Replacement clip for BMW door-sill/entry trim panels. The creator explicitly lists E21, E30, E36, E39, E46, E81/E82/E88, F20, E85 and related applications and identifies genuine BMW clip 51471840960. Verify the receiving-hole and trim thickness before fitting.

Fits 1 Series · E81 / E82 / E87 / E88 · 1 Series · F20 / F21 · 3 Series · E21 +5

Two-piece reinforced replacement shell for the original two-button remote and key blade, assembled with four M2 screws and the original key screw.

Fits Land Cruiser Prado · 120 Series

Workshop wrench for removing and tightening the fuel-sender retaining ring.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Printable male connector bodies and mounting parts for the original dashboard E-switch and hazard-switch positions.

Fits Defender · Td5