Find your next part.

We did 6 different version to get it in the angle that it faces the driver. We had a tight fit so it did not need any mounting to the dash, but maybe some glue or other adhesive wouldn't hurt. Printed flat down on the surface, with ABS+ to resist the summer heat in the car. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Repair bushing for the E46 and E53 window regulator, physically assembled and load-tested by the creator with an M6 thread. The creator warns that ordinary PLA failed in summer heat. Use heat-resistant automotive material, dry-fit before fastening, and verify glass, latch, wiring and trim clearance through full operation.

Fits 3 Series · E46 · X5 · E53

Two-gauge replacement for the BMW E36 centre vent. Only the physically printed and installed double-52 mm variant is retained from the source; its other untested variants are excluded. Confirm gauge depth, wiring, visibility and remaining demist airflow.

Fits 3 Series · E36

Replacement sunroof-motor cover for BMW E36 Coupe, with separate switch-cutout and plain versions plus the source 3MF. The source shows a finished print and physical installation. Use cabin-heat-resistant material and verify switch, motor, headliner and retaining-clip clearance.

Fits 3 Series · E36

Replacement centre-vent insert measured from a BMW E36 323ti Compact and physically installed with a 52 mm gauge. It sacrifices vent airflow at that position; use cabin-heat-resistant material and verify gauge, wiring and dashboard clearance.

Fits 3 Series · E36

Contour spacer demonstrated with aftermarket side repeaters on BMW bodywork. The creator lists E36 from October 1996, E46 sedan/Touring, E60/E61, E81/E82/E87/E88 and E90–E93 applications. Test one side before mirroring and verify the repeater remains weather-sealed and positively retained.

Fits 1 Series · E81 / E82 / E87 / E88 · 3 Series · E36 · 3 Series · E46 +2

Replacement knob specifically for the late-model E30 manual sunroof crank, shown physically installed. Use cabin-heat-resistant material and verify that the crank turns and folds freely.

Fits 3 Series · E30

Replacement E30 centre-console spacer that prevents lower trim deformation, copied from the original and physically installed. BMWFans confirms spacer 51161943121.

Fits 3 Series · E30

Replacement E30 electric window-lifter spacer for mechanisms through April 1988, reproduced from the original and physically installed. BMWFans confirms spacer 51331919541; power-window mechanisms only.

Fits 3 Series · E30

Replacement front-seat rail nut cap for early cars from September 1985 onward and late-model E30, copied from and physically compared with the original. BMWFans confirms covering cap 52101941999.

Fits 3 Series · E30

Snug-fitting flat cover for the E30 power-antenna opening. The creator reports it stays in place without extra fasteners; confirm the body opening, weather sealing and retention before road use.

Fits 3 Series · E30

Dimensioned replacement glovebox damper pin for BMW E21, E28, E30, E31, E34, E38, E39, E46 and E60/E61. The creator identifies BMW pin 51161828956 and shows the physical result installed. Verify damper eye and panel thickness before fitting.

Fits 3 Series · E21 · 3 Series · E30 · 3 Series · E46 +6

Service wrench for the notched BMW fuel-tank screw cap used on E46, E60/E61, E63/E64, E65–E68, E83 and E53 vehicles. The creator tested the same interface on an R53 MINI and identified BMW screw cap 16116762417; BMW catalog cross-reference independently confirms that cap across the listed BMW chassis. The printed wrench is not the screw cap itself, so no OEM number is assigned. Use a stiff engineering polymer, hand tools only, and replace rather than reuse any visibly damaged print.

Fits 3 Series · E46 · 5 Series · E60 / E61 · 6 Series · E63 / E64 +3

Replacement for BMW OEM part 51478230749 (Support for Tension Strap). Used to secure the trunk floor panel in BMW E39 E36 models. Printing recommendation: For maximum strength, print the part at a 45° angle using supports. This print orientation improves layer adhesion in the areas subjected to the highest load, resulting in a stronger and more durable part. BMW catalog lists support 51478230749 from 1996-09 and records bilateral interchangeability with superseded 51478197822; retain the creator-listed E36/E39 fitment. Verify dimensions against the original part and confirm full operation before regular use.

Fits 3 Series · E36 · 5 Series · E39

Battery-retaining spacer reproduced from BMW component 61211350825 for E30, E34, E39 and E46. BMWFans identifies it as spacer 1350825 and confirms those chassis among broader BMW usage. Match battery size, tray slot and hold-down engagement, and do not use it to compensate for an incorrect battery or damaged clamp.

Fits 3 Series · E30 · 3 Series · E46 · 5 Series · E34 +1

Replacement black blanking cover for an unused dashboard switch opening on BMW E32, E34, E36 and Z3. The source gives interchange number 51161963979, which BMWFans confirms as black cover 1963979 produced from April 1987; the alternate 51161963987 could not be catalog-confirmed and is intentionally omitted. Check color, opening and switch-bank configuration.

Fits 3 Series · E36 · 5 Series · E34 · 7 Series · E32 +1

Two-piece repair bushing for the riveted rear window-regulator slider used on BMW E32, E34 and E36. The creator built it for a personal repair so the original rivet can remain in place, and retained the two halves with friction plus an O-ring. Inspect the regulator, lubricate the guide correctly and confirm smooth glass travel before refitting trim.

Fits 3 Series · E36 · 5 Series · E34 · 7 Series · E32

Replacement throttle-body linkage/cable nipple for the M10-powered BMW E28 518i; two identical pieces are required in the catalog assembly. The design is based on an original part and includes print-orientation guidance. BMW number 13541286378 is cataloged specifically for E28 518i M10 applications and selected M10-powered E30 models, not every E28 engine.

Fits 3 Series · E30 · 5 Series · E28

Two alternative lower hook-holder geometries for the BMW accessory rear roller sunshade: an original-dimension version and a tighter-fit version tested in an early 1985 car. BMW references include discontinued white accessory hook 82129413177 and anthracite holder 51461905393, which supersedes 51461887130. E28/E30 body, production date, color and accessory installation vary; compare the no-screw-hole mounting style before use.

Fits 3 Series · E30 · 5 Series · E28

Adjustable clutch-pedal stop body for manual-transmission BMW E28 and other listed classic BMW chassis. Assembly requires an M10 screw, two M10 nuts, a 40 mm washer and a genuine-style rubber cap. Adjust only far enough to remove excess pedal travel while preserving complete clutch disengagement, then lock the nuts securely and re-check operation before driving.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46 +4

Left and right replacement brackets for retaining the metal badge inserts in BMW G20/G21-family all-weather floor mats. The creator reports iterative fit testing and explains that the metal tabs pass through the bracket openings before the bracket is press-slid into place. Use PETG or ABS, fit only to the mat badge area, and verify the mat remains fully anchored with no loose piece or raised edge near any pedal before driving.

Fits 3 Series · G20 / G21 / G28 / G80 / G81

Console insert for BMW G20 and G21 3 Series cars without the factory wireless-charging trim, physically shown installed after removal of the original rubber mat. It accepts an Apple MagSafe puck, a 90-degree USB-C adapter and a slim 12 V USB-C adapter. Use cabin-heat-resistant material, secure and protect the cable, preserve access to controls and cup holders, and confirm the phone remains retained without obstructing driving controls.

Fits 3 Series · G20 / G21 / G28 / G80 / G81

Two-piece fold-down bag hook designed and physically demonstrated in the trunk of a BMW G20 3 Series. Install with an M6 nut, a 25–40 mm M6 socket-head bolt and a temporary nut-retaining aid as described by the creator. Use cabin-heat-resistant material, confirm the mounting point is structurally suitable, keep the load light and verify the hook and cargo cannot interfere with the trunk lid, wiring or emergency equipment.

Fits 3 Series · G20 / G21 / G28 / G80 / G81

TPU clutch-stop set in 10, 12, 14 and 16 mm heights for manual BMW F3x models; the creator reports the 16 mm version installed with the factory clutch. Use the specified material, inspect layer adhesion and fit, and stop if the part interferes with safe service or pedal operation.

Fits 3 Series · F30 / F31 / F34 / F80