Find your next part.

Attaching the trailer socket bmw e60 / e61 Retain only the socket mounting bracket; verify trailer wiring and legal requirements independently. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

The nasty clips at the back of the headliner which always breaks when removing. Works very well with PETG. For non commercial use only! Creator reports the PETG replacement works very well at the rear of the E61 headliner. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Screw clip for BMW sub-panels. I used it for e60 100% infill (or less is also good) 0.2 layer hight Creator reports using this 30 mm screw clip on an E60 under-panel. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Just a replacement for the original Dummy. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

EDITED! THIS IS THE ACCURATE MEASUREMENTS. FITS PERFECT! LxBxH 30x15x20mmm Broke some clips when i took down some of my headliner, and could not find any so i made drawn and made some. Clips for headliner in BMW E60 an E61. Creator states the revised dimensions fit perfectly after replacing the earlier version. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Rear wiper gear BWM E60 Creator supplies physical comparison evidence. This rear-wiper part is for the E61 Touring body, not the E60 sedan. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Replacement for BMW OEM part 51478230749 (Support for Tension Strap). Used to secure the trunk floor panel in BMW E39 E36 models. Printing recommendation: For maximum strength, print the part at a 45° angle using supports. This print orientation improves layer adhesion in the areas subjected to the highest load, resulting in a stronger and more durable part. BMW catalog lists support 51478230749 from 1996-09 and records bilateral interchangeability with superseded 51478197822; retain the creator-listed E36/E39 fitment. Verify dimensions against the original part and confirm full operation before regular use.

Fits 3 Series · E36 · 5 Series · E39

I designed these brackets because the original BMW E39 tweeter mounts are too small to fit the Gladen Alpha 130 G2 tweeters. Installing aftermarket tweeters in the factory location can be challenging, as the available space inside the original E39 mounting brackets is very limited. These adapters allow the Gladen tweeters to be mounted securely while retaining the factory installation position. Compatible Speaker Set Gladen Alpha 130 G2 Original BMW Parts Left side: 65138362527 Right side: 65138362528 OEM reference: Printing Notes Designed for BMW E39 factory tweeter locations. Tested with Gladen Alpha 130 G2 tweeters. PETG or ASA is recommended for improved heat resistance inside the vehicle. Print with at least 3 perimeters and 30–40% infill for good durability. I hope this model helps anyone upgrading the factory audio system in their BMW E39. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Replaces the integrated plastic tab that commonly shears off, allowing the fog light to be secured without replacing the entire bumper. The bracket replicates the factory slot geometry. Once bonded, the fog light housing slides into the bracket and locks into place using the original mounting hardware/method. Material: Would recommend ASA or ABS. Compatibility: 2001–2004 (Facelift / LCI) BMW E39 5-Series models. Will not fit Pre-Facelift or M-Sport/M5 Bumpers. I also sell the printed parts: Installation Instructions: 1. Access: Gain access to the fog light assembly either by removing the front splash guard in the wheel well or by removing the front bumper entirely. 2. Alignment: Leave the fog light attached to the bumper by its remaining intact mounting point. 3. Test Fit: Position the repair bracket and verify that it makes flush contact with the bumper surface. Ensure the circular tab on the fog light housing slots correctly into the bracket. 4. Preparation: If remnants of the broken original bracket interfere with the fitment, trim them down until the repair bracket sits flush. 5. Bonding: Thoroughly clean the contact areas on both the bracket and the bumper. Apply a strong epox Creator limits fitment to the facelift/LCI bumper. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

BMW E39 523I glovebox nut PETG,ABS or other Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

This speaker plate is designed for the BMW E39 speaker enclosure and replaces the original crossover filter. Allows the box be airtight when using with aftermarket speakers for better sound quality. Cable hole is designed for 2x1.5mm2 cable Hole size is: 7mm x 4mm Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Prefer to use Nylon or another filament with great cohesion (My clips was printed with Nylon-GF) Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Center-compartment insert for a BMW E39, designed as a sturdier alternative to the loose factory cup holder. It fits in the storage recess directly in front of the original holders and accommodates cups up to 73 mm in diameter plus a phone up to 75 × 10 mm. Use cabin-heat-resistant material, verify the dimensions against the console, and confirm secure retention and unobstructed operation.

Fits 5 Series · E39

BMW E39 dashboard hole cover no glue needed(for my car it was tight fit, but not too tight) Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

I made this part to hook on the little white knob to move the seat. I printed it with the arrows showing on top. 0.5mm extruder, 1h print time. supports on. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

This is the design I made to replace my broken sun visor clip in my 2000 BMW E39 528i Touring. It is a little difficult to snap in but has a nice fit once it's clipped in all the way. Some filing or sanding might fix the stiff fit. Creator reports fitment in a 2000 E39 528i Touring. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

...trying to fit aftermarket speakers in my e39 bmw i found out that they leave a gap to the standard boxes in the front doors. so i quickly designed these simple rings to close the gap, Use TPU to print them to ensure a tight fit. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

hey ho, got a couple of used AC Schnitzer type 2 rims with the center hub caps missing, so i designed a simple and clean version. may require some sanding and spraypainting afterwards to fit your rim color. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

You probably do not use your E39 bluetooth phone anymore. Don't waste this space in your car and print my inlay to make this area useful for you. There are different versions available, I hope you will be able to chose the most fit for you;) I personally use the one with the grooves for phones. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

I wanted 16,5cm speakers in the roof of my e39 touring. So I designed an adapter, thought other would want to do the same The hole pattern in the roof is slightly nonsymmetric so you'll have to print a mirrored version as well Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Ther is the Mirror cover bmw e39 latch instead broken one! For each cover you need 2 direct and 2 mirror printed parts. Just put on things to the broken parts, try to put cover on mirror (i need to cut height for 2 of them) and fix it with glue. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Clip for sunblind holder BMW E38 E39 Printed ABS. Nozzle 0.2, layer height 0.01, speeds 40 - internal, 30 - external. Printing is carried out in two halves, after which it is glued together, processed mechanically and in acetone to give a presentable surface. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39 · 7 Series · E38

This thing was made with Tinkercad. Work In progress. For BMW Center Console Storage Coin Tray replacement. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Pair of reinforcement brackets for fitting a universal T2/T3 cup holder in a BMW E39. The creator reports that it supports McDonald’s drink sizes without smaller cups tipping and accepts PET bottles up to 0.5 litres. Print two brackets in ABS or PETG; PLA can deform in summer cabin heat. After printing, tap M4 threads in the holes, shorten the screws so they sit flush without protruding, and attach the brackets to the cup holder. These replace the unstable sheet-metal clips supplied with the universal holder. Verify dimensions, fastening, and unobstructed operation before regular use.

Fits 5 Series · E39