Find your next part.

Console for mounting auxiliary switches or other equipment in the small driver-side dashboard recess. Blank and pre-drilled versions are included for both left- and right-hand-drive vehicles

Fits Defender · L663

Base-plate adapter for fitting GMC/Chevrolet pickup tie-down anchors to the cargo-area ceiling. Installation uses two 3/8 × 1.5-inch carriage bolts with washers and nuts.

Fits Defender · L663

Four-piece replacement repair set for the air-conditioning louvre assembly in a 1995 Land Rover Defender 300 Tdi (1994-1998), comprising the louvre, outer frame, alignment strip, and louvre clip rail. The louvre-fit holes require drilling to 2.5 mm; the louvre requires supports and the other components print without supports. Verify the exact AC vent variant, hole size, retention, louvre movement, and cabin-heat material suitability before installation. This should also fit other pre-puma/td4 Defenders

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Replacement blanking plate for unused dashboard switch openings in the Land Rover Defender TD5 (1998-2005). It fills a dashboard opening where a switch is not fitted. Verify the exact dashboard aperture, dimensions, retention, and clearance before installation. PETG is the specified printing material; support is specified for printing.

Fits Defender · Td5

Full-size upper dashboard panel for the Land Rover Defender Td5 (1998–2005), replacing the upper dashboard top/facia component across the instrument-panel area. Verify VIN and windscreen/vent variant, drive side, demister and fastener interfaces, dimensions, clearances, and material/print strength before installation.

Fits Defender · Td5

Drop-in ashtray-delete dash mount base for the Land Rover Defender Td5 (1998-2005). It replaces the factory top-dash ashtray with a flat, level surface for adhesive or non-slip mounting of a display, GPS, dashcam, or similar accessory, and includes a cable-routing opening. No drilling or permanent dashboard modification is required; verify the dashboard opening, device footprint, clearances, cable path, and printed-part strength before installation.

Fits Defender · Td5

Blanking panel for the rear climate-control aperture in the Land Rover Defender L663 cubby box. It closes the unused opening when the cubby box is installed in a vehicle or configuration without rear heating controls.

Fits Defender · L663

Cubby-box dock for a cased Samsung Galaxy S5 and a cylindrical Qi charging puck.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Two replacements for the unused 1998 centre-panel opening: a plain plug and a post-mounted version for a small air freshener.

Fits Defender · 300 Tdi · Defender · Td5

Three-piece adaptor set for fitting a 1995 Ford F-150 throttle-position sensor to a 1994 3.9-litre V8 throttle body. The creator specifies PETG for engine-bay heat resistance.

Fits Defender · 300 Tdi

Replacement interior end cap for the roof reinforcement bar.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Modular dashboard panel for three rectangular switches, supplied as a one-piece version and a split panel with end cap.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Two dashboard vent inserts that redirect cabin airflow.

Fits Defender · Puma

Two-part dashboard hanger and extension for an Anker Soundcore Motion Boom portable speaker.

Fits Defender · 200 Tdi · Defender · 300 Tdi

Dashboard holder for mounting a compact CB radio in the Puma interior.

Fits Defender · Puma

Three panel variants for combining switches and a voltmeter, designed for the 200 Tdi dashboard.

Fits Defender · 200 Tdi

Bezel for installing a 30 mm USB charging outlet in the unused position beside the rear-wiper control on the centre console. The USB outlet clamps the bezel in place.

Fits Defender · Td5