Find your next part.

Replacement bulb socket for the clearance/parking lamp in the headlamp, explicitly identified by the creator as A2108260582 for 208- and 210-series cars. The source provides one author-downloadable STL and one CAD image but no physical fit photograph. Official Mercedes parts-store metadata identifies the exact child as the clearance-lamp socket for CLK 208 and E-Class 210. Verify VIN and headlamp variant, use heat- and flame-resistant electrically insulating material, transfer the correct contacts and bulb without damaging insulation, and test retention, polarity, lamp output, sealing and heat behavior before road use.

Fits CLK · C208 / A208 · E-Class · W210 / S210

Ten-card organizer sized for the eyewear/storage compartment in the centre console. The creator explicitly identifies 210-series fitment and notes compatibility with a separate mini-drawer, but provides only a CAD source image and does not establish other models. Use cabin-heat-resistant material, confirm compartment dimensions and lid travel, and ensure cards remain retained without obstructing the selector or other controls.

Fits E-Class · W210 / S210

Phone tray with an accessory USB charging socket for the rear centre-console cover position. The creator states 210-series use, 3M VHB or Tesa ACXplus adhesive mounting, and supplies the original-cover comparison plus the physical tray; no installed follow-up image is present. Use cabin-heat-resistant insulating material, a fused automotive-grade USB module and strain relief, preserve rear-console and seat travel, and verify adhesion and wiring clearance before use.

Fits E-Class · W210 / S210

Modular replacement for the centre-console ashtray insert, with USB-power and optional 50-cent coin-dispenser configurations. The creator states 210-series fitment, documents an installed dimensional correction, and specifies a 9 x 35 mm spring and adhesive for the dispenser components; source photographs show loose physical assemblies and the wired USB insert. Use cabin-heat-resistant insulating material, a fused automotive-grade USB module and strain-relieved wiring, keep conductors and coins isolated, and confirm selector and console clearances.

Fits E-Class · W210 / S210

Adapter for the original Nokia phone mounting point, intended to accept contemporary phone holders. The creator explicitly identifies 210-series fitment and supplies a photograph of the physical print. Confirm the factory cradle profile and the chosen holder interface, use cabin-heat-resistant material, secure the phone without obstructing controls or airbags, and verify it cannot detach under braking.

Fits E-Class · W210 / S210

Replacement handle for the climate-control panel. The creator states exact 210-series use and provides four CAD views plus a printable part and an editing variant, but no installed photograph or detailed trim/market split. Compare the original handle, shaft and panel before printing, use cabin-heat-resistant material, keep the control mechanism free of debris, and verify full smooth travel and the correct setting indication after installation.

Fits E-Class · W210 / S210

Direct replacement for the hidden hinge base inside the leather-covered door-mounted cup holder, developed on a 300E from the 1984-1996 period. Source photographs show the physical base and cup-holder assembly. Match the door and holder variant, reuse the original covering and backing carefully, use tough cabin-heat-resistant material, and verify full folding travel, secure retention and unobstructed door operation.

Fits E-Class · W124 / S124 / C124 / A124

Replacement drain grommet for the plastic box below the right headlamp on the air-intake side. The creator states all 124-series chassis, a slightly tighter body fit and a changed drain shape. Use heat-, weather- and fluid-resistant flexible material, confirm the right-side box and opening, preserve an unobstructed downward drain path, and verify the grommet cannot admit water to wiring or the air intake.

Fits E-Class · W124 / S124 / C124 / A124

Standard- and loose-fit replacement grommets for mounting the hydraulic self-levelling suspension oil reservoir on estate cars. The creator identifies the exact child as A1299971681. These grommets support only the reservoir, not a suspension load path. Use oil-, heat- and vibration-resistant flexible material, match the mounting hole and reservoir pin, and inspect for leaks and secure retention after installation.

Fits E-Class · W124 / S124 / C124 / A124

Replacement grommet through which the radiator lower locating prongs pass. The source establishes 124-series fitment but provides only model imagery. This grommet isolates and locates the radiator; it is not a structural vehicle mount. Compare the original opening and radiator pin, use engine-bay heat-, coolant- and vibration-resistant flexible material, and confirm secure seating, fan clearance and leak-free hoses after installation.

Fits E-Class · W124 / S124 / C124 / A124

Two replacement shaft-lock variants for the headlamp-wiper motor assembly: K for SWF motors and L for SWF or Bosch motors. The creator tested both on original assemblies and documents the installed position. Identify the motor maker before printing, use heat- and weather-resistant material, preserve cable potting, and bench-test motor retention, full sweep and parking before road use.

Fits E-Class · W124 / S124 / C124 / A124

Direct replacement for the lower condenser mounting grommet identified by the creator as A2019970381. The source model intentionally simplifies fillets and tightens the fit for printing. Compare the original grommet and condenser pin, use heat-, weather- and vibration-resistant flexible material, and confirm the condenser is retained without metal-to-metal contact or stressed refrigerant lines.

Fits E-Class · W124 / S124 / C124 / A124

Replacement clip used in pairs to secure the lower engine wiring harness to the engine block; the creator notes that the same size also appears elsewhere. Exact routing varies with engine and model year, so compare the original clip and mounting point rather than inferring other positions. Use engine-bay heat-, oil- and vibration-resistant insulating material, avoid sharp wire contact and confirm the harness cannot reach hot or moving parts.

Fits E-Class · W124 / S124 / C124 / A124

Insert replacing the disassembled centre-console fader-switch mechanism to retain a USB extension cable from an updated head unit. The source supplies the insert model and console-fit imagery but no electrical hardware. Confirm the early console opening and cable connector, use cabin-heat-resistant insulating material, provide strain relief and fusing for the connected accessory, and keep wiring clear of the selector and original harness.

Fits E-Class · W124 / S124 / C124 / A124

Replacement covering/clip for retaining the vapour barrier behind the interior door panel. The creator explicitly identifies both 190-series and 124-series applications, supplies numbered and unnumbered geometry, and recommends glass-fibre-reinforced polypropylene with controlled support separation. The controlled material taxonomy does not include that polymer; nylon is listed only as a durable alternative and requires fit validation. EPC applicability maps the exact covering to both chassis families. Match the original profile, avoid tearing the moisture barrier, and confirm the door panel seats without bulging.

Fits 190 Series · W201 · E-Class · W124 / S124 / C124 / A124

Custom dashboard air-vent adapter for a standard 52 mm temperature, voltage, oil-pressure or lambda gauge. The creator explicitly states fitment to both 190-series and 124-series vents. Confirm steering-side vent geometry, gauge depth, wiring and hose routing; fuse electrical additions, avoid sharp edges and preserve driver visibility and remaining ventilation.

Fits 190 Series · W201 · E-Class · W124 / S124 / C124 / A124

Two-piece retaining clip and screw cover for the cabin sun visor. The creator made it for a 1989 300E and explicitly states W123, W124, W126, W140 and W201 fitment, while noting that it does not carry electrical contacts for illuminated vanity mirrors. Print the main clip and locking cover in the documented orientations, use cabin-heat-resistant material, compare the screw position and visor profile, and confirm secure retention and free release before driving.

Fits 190 Series · W201 · E-Class · W124 / S124 / C124 / A124 · S-Class · W126 / C126 +2