Find your next part.

Full-size replacement slider guide for the dashboard ashtray on Ford Bronco vehicles from 1992–1996 and Ford F-Series vehicles from 1992–1997. The printed component keeps the ashtray supported in its dashboard tracks so it can slide and remain in place. The ashtray and any mounting hardware are separate components. Slight sanding of the top and bottom may be needed for a snug fit; the creator recommends PETG and supports for printing.

Fits Bronco · Fifth generation · F-Series · Ninth generation

Two-piece replacement mounting set for the vacuum actuator on top of the factory air-conditioning box. It adapts the installation to a Dorman 604047 vacuum actuator; installation requires reworking the actuator arm with a screw and nut, trimming the replacement actuator to fit, and using two M3×6 and two M3×8 screws. Verified fitment is 1965–1968 Ford Galaxie.

Fits Galaxie · Fifth generation

Replacement protective cap for the rear wiper arm, covering the exposed arm hardware at the rear window. Intended for the 2013–2021 Qashqai/Dualis J11 generation (North American Rogue Sport application); verify arm geometry, retention, and clearance before use.

Fits Qashqai / Dualis · J11

Four-piece set of printed repair components that restores the mounting points on a rear hatch handle by replacing broken internal clip blocks and reusing the original handle hardware. The set includes left- and right-side clip components plus inner and connector pieces for the Qashqai / Dualis J10 (2006-2013) application. The printed parts are bonded to the original handle and require fit checking before installation.

Fits Qashqai / Dualis · J10

Engine-bay bracket for mounting the coolant reservoir after removal of the factory fuse-box mounting location on the Nissan S13/180SX/200SX/240SX family. The printed part provides the reservoir support interface; the reservoir and fastening hardware are not included. Use a heat- and weather-resistant material suitable for engine-bay service and verify fit, clearance, and secure retention before operation.

Fits Nissan 180SX · RS13/RPS13 · Nissan Silvia · S13

Door-mounted spacer ring for installing a 165 mm (6.5-inch) aftermarket speaker in the front door speaker location of the Nissan March/Micra K11 (1992–2002). The ring increases clearance for a less-shallow speaker and provides the vehicle-side and speaker-side mounting interfaces; the speaker, wiring, fasteners, locknuts, and shims are separate components. Verify the exact speaker diameter, mounting depth, hole alignment, window and trim clearance, wiring routing, fastening, and vibration isolation before installation.

Fits March · K11

Two interchangeable full-size intake adapters for mounting CA18DET or SR20DET mass-airflow sensors to compatible A'PEXi filters. Includes separate SR20 and CA18 adapter geometries and requires a 3 mm O-ring cord assembled into the seal groove; printed parts only, with filter, sensor, O-ring cord, and hardware not included. Fits S13, S14, and S15 applications with the corresponding MAF and filter interfaces; verify sensor variant, sealing, fastener engagement, intake clearance, and engine-bay heat resistance before use.

Fits Nissan Silvia · S13 · Nissan Silvia · S14 · Nissan Silvia · S15

Replacement center-console armrest USB pass-through cover that replaces the factory USB socket surround and lets a Lightning cable pass through while routing the cable to an under-armrest interface. Includes the printed cover only; the cable, tie, and any electronics are separate. Fitment is verified for the Nissan GT-R R35 (2007-2025). Creator guidance specifies Nylon CF and recommends against PLA for hot vehicle interiors; verify the connector, cable tie, armrest opening, and clearances before installation.

Fits Nissan GT-R · R35

Replacement cabin-light housing for the overhead interior lamp opening of the Nissan/Datsun 720 pickup, generation 2730 (1979-1986). The single printed piece provides the perimeter clips, mounting holes, and central lamp recess. The lamp, lens, wiring, and fasteners are not included; verify the roof opening, lamp hardware, clip engagement, clearance, and retention before installation.

Fits Datsun Truck/Navara/Frontier/NP300 · 720

3-inch air-filter adapter for mounting a cone filter to the factory naturally aspirated MAF sensor on the Nissan 300ZX Z32 (1989–2000). The screw-in version has 7 mm holes intended for 6 mm bolts and nuts; the filter, MAF sensor, and mounting hardware are not included. The creator specifies ABS and notes PETG or nylon as suitable alternatives.

Fits Fairlady Z / Nissan Z · Z32

Two-piece mounting set for a rear wing, comprising a trunk-mounted wing mount and a separate stand component. Intended for the Nissan 350Z Z33 (2002-2009) and an APR GTC-500 wing; the mount uses two M8 threaded inserts beneath the wing at the rear trunk. Verify dimensions, fastener engagement, and structural suitability before installation.

Fits Nissan Z / Fairlady Z · Z33

Replacement lower dashboard air vent for Nissan Primera P10 (1990–1996), intended to restore the under-dash HVAC outlet. The source-authored 3MF contains the vent geometry as one mesh; installation and fitment should be verified against the original vehicle opening.

Fits Primera · P10

Two protective covers for exposed intake and exhaust ports on an SR20 engine. The intake cover is sized for the S13 SR20 configuration, while the exhaust cover is described as compatible across SR20 generations. The covers protect open engine ports from debris during engine storage or installation and include separate intake and exhaust cover components.

Fits Nissan Silvia · S13

Replacement dashboard air-vent insert with a 52 mm round gauge opening for the Nissan March/Micra K11. It replaces a side dashboard vent and provides a factory-style mounting location for one 52 mm gauge. The source set includes standard and mirrored STL variants for handed installation; the gauge, vehicle, and non-printed hardware are not included. Verify vent-opening geometry, side/orientation, gauge clearance, retention, and cabin-temperature material suitability before installation.

Fits March · K11

Full-size dashboard side-vent trim panel for the 1978–1983 Nissan Fairlady Z / Datsun 280ZX S130. The single-piece geometry forms the vent surround/trim shell with vent openings and integral mounting posts. The creator recommends 3–4 wall layers for rigidity and ABS, ASA, or PC for cabin heat; verify side orientation, retention, and fit before installation.

Fits Fairlady Z / Datsun Z · S130

Replacement rear-window latch arm for the Nissan D21 King Cab sliding rear-window assembly. Restores the latch retaining function at the rear window; the supplied model is one printed arm, while the window assembly and installation hardware are not included. Print in PETG with supports as specified, and verify the window variant, arm and fastener interface, clearances, and secure retention before use.

Fits Datsun Truck/Navara/Frontier/NP300 · D21

Full-size replacement wheel center cap for the 2002–2009 Nissan 350Z (Z33) application. It covers the center opening of a compatible alloy wheel and carries a raised Nissan emblem. Verify the wheel package, cap dimensions, retention, and clearance before installation; use a heat-resistant material suitable for wheel service.

Fits Nissan Z / Fairlady Z · Z33

Replacement climate-control knob for the dashboard air-conditioning and heater panel in the first-generation Nissan X-Trail T30 (2000–2007). The knob operates one of the panel controls and includes the source geometry for the shaft interface and position-indicator light slot. Includes one knob; verify the panel variant, shaft engagement, rotation range, indicator alignment, and secure retention before installation. PETG or ABS is recommended for cabin heat resistance.

Fits X-Trail · T30

Replacement clip for attaching the rear parcel shelf to the rear locators on the backs of the rear seats of the Nissan X-Trail T30 (2000-2007). The printed component restores the clip interface; verify seat-back locator geometry, orientation, fit, retention, and clearance before installation. Print in PETG or ABS for improved resistance to cabin heat and confirm secure retention before use.

Fits X-Trail · T30

Replacement left- and right-hand rear cargo-cover hooks for Nissan X-Trail T30 vehicles from 2000-2007. The source set provides four handed and position-specific STL variants for retaining the retractable boot/tonneau cover at the rear interior side panels. Print the applicable variant or variants, compare the mating profile with the original, and verify side, fit, retention, clearance, and material suitability before installation.

Fits X-Trail · T30

Replacement cover for the rear window wiper arm using the 28782-ED500 interface. Verified fitment covers Nissan Juke F15, Tiida C11, X-Trail/Rogue T32, Pulsar C13, and Kicks P15 where that exact rear cover is used. The single-piece cover replaces the original outer cap; the design notes that the lower spikes may need slight trimming to ease installation.

Fits Juke · F15 · Kicks · P15 · Pulsar · C13 +2

Two-piece replacement clip assembly for the rear parcel shelf, retaining the shelf at the tailgate trim. Includes the clip body and retaining pin as separate printed components. Verified fitment is Nissan Juke F15 (generation 2748); vehicle and any non-printed hardware are not included. Verify dimensions, material suitability, seating, and retention before use.

Fits Juke · F15

Two-piece dashboard navigation-device holder for the Nissan NV200 M20. The holder seats in the opening on top of the dashboard, supports a TomTom Go5200 or compatible suction-cup device up to 60 mm, routes the power cable through provided openings, and is retained with double-sided tape. Includes the main holder and top cover; tape, navigation device, and other hardware are separate. PETG or ASA is recommended for cabin heat exposure.

Fits Nissan NV200 · M20

Replacement translucent insert for the broken internal section of a manual/standard heater-control knob. Fits the standard heater-control panel represented by the 2003 application within Nissan X-Trail T30 generation 2903; it is not intended for climate-control panels. The insert restores the knob shaft interface and light-transmitting inner piece. Clean and fit carefully: the documented test fit did not seat fully, and forcing the insert can damage the shaft.

Fits X-Trail · T30