Find your next part.

Custom panel for a Range Rover P38 stock radio slot, holding auxiliary switches, the ride-height switch, and the interior-air-temperature sensor after relocating the original radio. This is a community accessory with no Land Rover Genuine part number. The source recommends printing the front panel flat on the bed at about 20% infill without supports.

Fits Range Rover · P38

Replacement electric sunroof latch.

Fits 924 · 924 · 944 · 944

Two-piece passenger-side interior door-pull conversion with a GT3-like shape. The creator says to mirror the files for the opposite side and attach the pull strap with a small screw.

Fits 911 · 997

Two headlining fastener sizes for a 110.

Fits Defender · Td5

Replacement center-console assembly laid out for a double-DIN radio installation.

Fits 924 · 924

Replacement blanking plate for the center-armrest storage opening after removal of the factory telephone cradle. The creator modeled it for the second-generation X5, shows it physically fitted and states that the friction-fit print replaces BMW cover 51 16 9 115 083 without reproducing the original clips. BMW catalog evidence also lists that cover for the contemporary X6 E71/E72. Confirm the telephone/storage-console configuration and applicable option equipment by VIN, use a heat-resistant material, and verify that the plate remains secure without interfering with adjacent wiring or sockets.

Fits X5 · E70 · X6 · E71 / E72

Replacement plus/minus volume rocker modeled after the creator's broken multifunction steering-wheel button and physically shown loose and installed. The creator documents direct fitment to X3 E83 and X5 E53. BMW services the surrounding switch assembly rather than this printed child button separately, so no parent assembly number is assigned. Use a durable heat-resistant material, preserve free button travel, and verify all steering-wheel controls operate without sticking before driving.

Fits X3 · E83 · X5 · E53

The center console catch broke in my BMW E61. I've removed the remaining plastic and printed this piece. Attach with two screws and it works perfectly again. Print with 100% infill for extra strength. Creator reports a perfect working repair attached with two screws; photographs show the installed E61 console lid. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Print with a filament that can survive the temperatures in the car. I have added the step so you could add buttons or anything else if you want. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

This is a remixed version of the original thing posted here on Thingiverse, which is a shift boot bracket for the BMW E46 3 Series. It has better strength as with the added fillets and the clips are thickened as well as enlarged for better fitment. It will fit both RHD and LHD BMW E46 and will provide tight fitment. If you are planning to install with thick Alcantara leather boot, then it will be wise to scale it down a bit to 96-97% scale but if you are just planning to use faux leather boot, then at 100% scale it will be just fine. Use custom support blockers to increase the infill density of the clips to 99% for added strength. Print it in ABS or PETG because PLA will definitely deform du Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Cup holder and 50-cent shopping-token recess for left-hand-drive first-generation BMW 1 Series centre consoles that lack the factory holder. The creator installed the printed assembly with double-sided tape and reports secure use. Both the single-piece model and the split top/bottom alternative are retained. PETG or ABS is recommended for summer cabin temperatures.

Fits 1 Series · E81 / E82 / E87 / E88

Replacement speaker-grille cover for the 1998 50th Edition, supplied as one complete piece or two halves for smaller printers.

Fits Defender · 300 Tdi

Repair set for later window-regulator motor assemblies, including gear-coupler and roller options. Some versions require drilling and tapping the original steel hub or roller shaft

Fits Discovery · 1

Land Rover defender mirror hinge bottom cap

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

This is a replacement part for the BMW 5 Series Touring (F11). It is the sliding clip ("leash" or "dog") located in the D-pillar track that automatically raises and lowers the rear cargo blind (luggage cover) when the trunk is opened. OEM Part Number: 51437232775 Tested on: BMW F11 520d Touring IMPORTANT INSTRUCTIONS 1. FUNCTION: This part slides inside the track of the rear pillar. It is crucial for the automatic retraction of the luggage cover. 2. LEFT vs RIGHT Side: The uploaded file is for the LEFT side. If you need the RIGHT side, simply use the "Mirror" function (along X-axis) in your slicer software. 3. MATERIAL RECOMMENDATION: Because this part moves in a track and bears weight, I strongly recommend printing with NYLON (PA). - Nylon provides the necessary low friction and high durability. - ABS/ASA might work but will wear out faster. - PLA is NOT recommended. 4. PRINT SETTINGS: - Infill: 100% (Solid) for maximum strength. - Orientation: Print in an orientation that maximizes layer adhesion strength for the pulling force. Designed from scratch as a cost-effective alternative to the expensive OEM repair kit. Creator-tested on an F11 520d Touring. The supplied file is the left sliding coupling; mirror on X for the right side. BMWFans identifies genuine BMW 51437232775 as Coupling, left, produced from 2010-06 for F11/F11 LCI European applications including LHD and RHD. Use nylon where possible, not PLA, and verify smooth movement before loading the blind. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

Fourth-iteration replacement for the small slider-rail clip used in creator-listed E36, E39, E46 and E53 sunroofs. The source shows the physical print and a working demonstration. Use heat-resistant material and verify full sunroof travel, anti-pinch operation and water sealing before driving.

Fits 3 Series · E36 · 3 Series · E46 · 5 Series · E39 +1

Driver-side and passenger-side replacement adjusters for the two central dashboard air vents.

Fits 4Runner · 4th Gen

Replacement ventilator control knob modelled from the original component.

Fits Series · 2

Dashboard bracket for a 9.3-inch portable CarPlay display. The upper edge tucks beneath the dashboard trim while taped feet support the screen

Fits Discovery · 3 · Discovery · 4

Height-setting blocks for calibrating Range Rover P38 electronic air suspension level sensors. Includes front and rear blocks for Access, Low, Standard, and High settings

Fits Range Rover · P38

Originally built to mount a Bolt&Trim Leather speaker holder for the Marshall speaker. This allows for a temporary/movable mount based originally on a cup holder. Could be easily modified for other speaker styles.

Fits Series · 1 · Series · 2 · Series · 2A

Land Rover Discovery 3 armrest cap.

Fits Discovery · 3 · Range Rover Sport · L320

Adaptor to fit Discovery 2 Cruise Control switch to Defender td5. Quote from SimonRafferty: "It's very easy to add cruise control to any Td5 Land Rover Defender just by adding a couple of wires to the ECU and connecting them to a switch. (search on line for details) Unfortunately, there are no nice looking switches. My solution was to fit a switch from a Td5 Discovery 2 - and print this adaptor so it can easily screw on to the steering column. This is version 2 which is a much better fit and prints in one piece. Use higher temperature filament such as PETG or PAHT - otherwise it will melt in the sun. That's how come V2 came to be! Insert a couple of M4 Nuts into the slots provided, then attach the switch with 2 x M4 x 10mm screws"

Fits Defender · Td5

Four-piece replacement repair set for the air-conditioning louvre assembly in a 1995 Land Rover Defender 300 Tdi (1994-1998), comprising the louvre, outer frame, alignment strip, and louvre clip rail. The louvre-fit holes require drilling to 2.5 mm; the louvre requires supports and the other components print without supports. Verify the exact AC vent variant, hole size, retention, louvre movement, and cabin-heat material suitability before installation. This should also fit other pre-puma/td4 Defenders

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5