Find your next part.

Coin holder for your Subaru Forester SH.

Fits Forester · Third generation (SH)

I was tired of there being a single large pocket in my center console. I will probably use this as a starting point for additional versions but the interfacing geometry that mates up with the existing console are all in the correct place. This should fit all SH series Subaru Foresters 2009 - 2012 Designed in Fusion 360

Fits Forester · Third generation (SH)

It never really felt right to put my round cup into the square cup holders in my Subaru so I decided to make an insert. I will probably tweak the round portion to work with different sized cups a little better but this version works great for my current coffee mug. The fit in the existing cup holder fits like a glove. Designed in Fusion 360.

Fits Forester · Third generation (SH)

It's a coinbox that fits in the middle console - the console with a hatch underneath the armrest.

Fits Forester · Second generation (SG)

Retention clip broke off form my fuse box door on my 2009 subaru forester. This is the one on the drivers side right near where your left knee would be. Printed on its side to give the bottom hinge clips some flex without breaking

Fits Forester · Third generation (SH)

The cover, plug or insert is for the transmission release whole that is usually in the upper left of the automatic shifter in the Subaru Forester. It is very similar to the Outback (Part No: 35181AG00A) however the Outback part is about half the height of the Forester Cover Release. The Cover Release is individual sold for the Outback but in order to get it for the Subaru Forester you have to buy the whole shift indicator plate (Part No: 35170FG080) for the console. It costs anywhere between $80-$125 dollars.

Fits Forester · Third generation (SH)

Subaru Forester SH 2009-12 To fit the large storage hole in the front centre dash area (below the heater controls)> I found I didn't like putting anything in there as it was always on "show" for potential thieves etc. So the idea was to have a small cubby hole with door, and then a small tray above (tray fits next to the 12v socket above the door/frame.) Works ok, is reasonable "neat" - fix in place using (a large amount of) double sided foam trim tape. PETG or ABS preferred due to heat in cars may warp PLA, but I have had success with PLA in cars, as long as not in direct light etc (which this is not). First attempt so could be improved. Dry fit and measure the position first, the frame needs to be in place first so measure vs the tray. 1mm x 6mm magnets in the lid/frame. 2mm (M2) bolts in the hinges of the lid. Feel free to modify or improve.

Fits Forester · Third generation (SH)

Pull Handle OPENNER for Subaru Forester SF LH can b mirr to RH? dntknw

Fits Forester · First generation (SF)

a shortram like K&N 69 Typhoon sportairfiltersystem for SUBARU FORESTER (SG) 2.5 XT / 69-8002TS ( https://www.knluftfilter.com/69-8002ts-performance-air-intake-system ) its fittet for 100mm K&N airfilter original MAF sensor

Fits Forester · Second generation (SG)

Modified to fit a Pocophone F1 with case horizontally, other phones may required longer or shorter arms.

Fits Forester · Second generation (SG)

Centre divider for the console next to handbrake area. I lost the removable "wall" so quickly knocked this up.. Fits fine, but doesnt stack on the other divider unfortunately.

Fits Forester · Third generation (SH)

My wife drives a Subaru Impreza and her passenger sun visor broke one day. Turns out a plastic connector piece broke roughly in half. Unfortunately you can't buy just the one piece that broke, you have to spend $90 to buy a whole new visor! So to save a little money I figured I'd design a replacement part. This is specifically for a 2017 Subaru Impreza Premium Sport Hatchback. It is only for the passenger side visor, but I imagine that a mirrored version would work on the driver side visor. I have included both the Fusion360 archive and a generated STEP file so that this can easily be remixed. Apologies in advance if remixing my design is a pain, I'm still relatively new to 3D CAD and this is the most complex thing I've designed so far.

Fits Impreza · Fifth generation (GK/GT)

Trying to find a phone mount that would work on my 2020 forester sk. I didn't want something that will block an air vent or go into my cd player or occlude my view to any displays or windows. I wanted it to work with my magsafe car adapter that I bought on amazon to work with my iphone. This mount will attach to the right side console right below the color trim. It utilizes a standard 17mm ball mount so it can work with any accessory that attaches with a 17 mm ball mount. I am using this magsafe car mount https://www.amazon.com/gp/product/B08CZPVLNL/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&th=1 The look is very clean and sturdy. I used 3M outdoor strength double sided stick pads to stick to the console.

Fits Forester · Fifth generation (SK)

If you like the design and wouldn't mind, please give me a watch and subscribe on youtube...I have videos designing these types of things from time to time and could use the support! My Youtube > https://bit.ly/35j5BL1 IG - @Myowncasualty IG - @EndMotive I printed this on an Elegoo Mars....supports will be hard to remove on an FDM printer without dissolvable support material. Fits LHD Subaru Forester SF/SG ....make sure your dash matches the one pictured. Includes 52mm and 60mm variant. No hardware or anything required. Just remove the factory dash vent carefully and this will clip in place just like the factory part. Also has a small routing hole to run wires. The vent still functions....just not as good lol.

Fits Forester · First generation (SF) · Forester · Second generation (SG)

This is a an adapter to mount a Yakima Ski Rack to my 2018 Subaru Impreza Stock Crossbars. Did not like the expensive adapters Yakima sells, they didn't seem as secure nor as stable. Print four of these in total, two for each rack. These adapters can snap over the crossbars and be slid into place. When the ski rack is tightened, the mounts grip and do not slide. I printed these in PETG. I did not strength test these, but have not had any problems driving at highway and interstate speeds. Will update with any problems. Might work with Subaru Crosstrek as well, since a lot of parts are interchangeable.

Fits Impreza · Fifth generation (GK/GT)

This is a simple tool for installing your Cam Oil seals flush (I got frustrated with useless install kits that pushed it in too far or not straight) This was for my Subaru Forester 2010 SOHC, it has 45 x 32 x 8.0mm cam oil seals Just tap in with a light rubber mallet, worked great Designed in Tinker CAD, which I am getting the hang of, bit by bit I used random z seam &10% support , comes out easy on PLA+

Fits Forester · Third generation (SH)

To get stability in the middle bottom area, you should bend a sheet metal strip by 90° and fix it in the direction of the rear bumper. take TPU, ABS are not durability

Fits Forester · Second generation (SG)

forester_sf_5_radiator_grill_mount

Fits Forester · First generation (SF)

This thing is a replacement part for 3rd gen Subaru Impreza cup holders. It may fit other Subaru models from that same period. It helps center a standard diameter beverage can in the cup holder so it doesn't slide around. It also collects condensation and leaked drink. It probably could use an extruded honeycomb pattern to give liquid a place to run off to...

Fits Impreza · Third generation (GE/GH/GR/GV)

A printer friendly version of pimaster's [2004 Subaru Forester Bonnet Stay Clip](https://www.thingiverse.com/thing:213626)

Fits Forester · Second generation (SG)

Clip-under cover, front, 56411FA000 Part 4 on this page: http://opposedforces.com/parts/forester/en_s11/type_9/body_equipment_exterior/under_cover_and_exhaust_cover/illustration_1/ Subaru Forester SG '04, April — '05, May '05, March — '06, May '06, April — '07, May '07, March — '07, November Part usage information Europe FORESTER S11 FORESTER S10 IMPREZA G11 IMPREZA G10

Fits Forester · Second generation (SG) · Impreza · First generation (GC/GF/GM) · Impreza · Second generation (GD/GG)

Horncover for Subaru Impreza G3 (2.0D) (60mm Horn)

Fits Impreza · Third generation (GE/GH/GR/GV)

Subaru Forester SH - Door pocket bin. Fits snugly into the door pocket. Store your sweet wrappers, tickets, etc in this handy bin. Push firmly to clip into place under the angled lip of the door pocket. .stl provided is for the right side (UK drivers), if you want the left, simply mirror the model in your slicer (pay attention to which direction you mirror!). Print in PETG/ABS etc if you live in very hot climates where PLA may soften in the heat. However for the sunny UK (!) I have found PLA is perfectly fine as its mostly protected from direct sun and heat in the door (used a similar bin in my old Forester for three years no issues). 0.25mm layers, 2 perimeters, 20% infill is fine = roughly a bit less than 5 hour print per bin. Nothing crazy - an easy print. Some overhang on the opening lip but should be within the capability of most printers!

Fits Forester · Third generation (SH)

A slip - in Fuel Cap holder for Subaru Forester (SH - Gen3) This version has been strengthened with gussets as the original version (In my experience in the Aussie Heat) Warped and split with the pressure of the cap after repeated use. I remixed the version by elanaut and added the Gussets I will most likely fit other model Subarus - just look for the pressings in the fuel door like in these pictures.

Fits Forester · Third generation (SH)