Find your next part.

Flexible protective cap for the front windscreen-wiper arm nut, print-tested by the creator in 95A TPU and shown installed. Match the spindle and arm version, use UV-, weather- and washer-fluid-resistant flexible material, seat it without contacting the moving arm, and confirm full wiper travel and retention after wet-weather operation.

Fits Vito / Viano / V-Class · W639

Two-piece flexible gasket for the rear-window wiper shaft. The creator explicitly describes it as a temporary fix because typical printable TPU is harder than the original rubber; installation requires removing the rear wiper motor. Use only as a temporary non-equivalent seal, match the exact shaft and glass interface, avoid loading or scratching the glass, and verify sealing, motor alignment and free wiper movement.

Fits Vito / Viano / V-Class · W639

Flexible replacement tether for the fuel filler cap, created after the original tether failed and shown installed on the filler door. Print in fuel-, UV- and weather-resistant flexible material, preserve the cap sealing surfaces and venting, keep the tether clear of the neck and hinge, and confirm the cap still seals and locks normally.

Fits Vito / Viano / V-Class · W639

Phone holder for the factory mounting point beside the steering wheel, designed around an iPhone 6 with a silicone case. The source includes an installed photograph and author STL/OBJ geometry. Verify device dimensions and the original mounting interface, use tough cabin-heat-resistant material, and confirm the phone cannot obscure instruments, interfere with steering or airbags, or detach under braking.

Fits Vito / Viano / V-Class · W639

Replacement wing nut used on several battery and storage-compartment covers. Source imagery shows the installed fastener location and the loose printed geometry. Match the original thread and cover version, print in tough cabin-heat-resistant material, do not force a mismatched thread, and tighten only enough to retain the non-structural cover without cracking it.

Fits Vito / Viano / V-Class · W639

Replacement retention clip for the bonnet support strut. The author supplies printable STL and editable STEP geometry plus a source photograph of the physical clip. Use engine-bay-temperature- and weather-resistant material, compare the strut diameter and mounting profile, and confirm the strut is retained when stowed without weakening or interfering with bonnet support or latching.

Fits Vito / Viano / V-Class · W639

Replacement locking pin for a seat armrest, redesigned with a toothed arc and used successfully by the creator with M3 and M4 nuts and screws. Compare the original geometry and armrest version, use tough wear- and cabin-heat-resistant material, secure the hardware against loosening, and verify the armrest locks and releases repeatedly without affecting the seat or belt before driving.

Fits Vito / Viano / V-Class · W639

Replacement frame and cover for the vanity mirror in the sun visor. The source shows the printed frame holding a mirror insert and the supplied author geometry. Reuse only safe, intact mirror material, smooth every edge, use cabin-heat-resistant material, retain the frame without stressing the visor, and confirm the cover closes securely and cannot fall into the driver field of view.

Fits Vito / Viano / V-Class · W639

Trim cover for the upper seat-belt height-adjuster anchor. Source photographs show the printed cover installed over the factory adjuster; it is cosmetic and must not carry belt load. Use tough cabin-heat-resistant material, preserve unobstructed adjuster travel, never cover damage or alter the belt, anchor or mechanism, and confirm the belt retracts, adjusts and locks normally after fitting.

Fits Vito / Viano / V-Class · W639

Replacement wardrobe-door locking tab for the Marco Polo camper interior. The creator supplies photographs comparing the printed and original pieces and shows the replacement installed. Print in tough cabin-heat-resistant material, match the wardrobe version and door alignment, and confirm the door remains securely latched through repeated opening, closing and road vibration before carrying contents.

Fits Vito / Viano / V-Class · W639

Replacement hook for the kitchen rail in a Marco Polo camper interior. Source photographs show the printed hook installed on the rail and carrying a light bag. Match the rail profile before use, print in tough cabin-heat-resistant material, deburr every sliding/contact face, and limit use to lightweight loose items that cannot become projectiles while driving.

Fits Vito / Viano / V-Class · W639

Smartphone holder that mounts into the original SAP V3/V4 Bluetooth cradle beside the steering wheel using the cradle connector and three factory mounting holes. The creator designed it around a Samsung Galaxy S5 with S-View cover; verify the phone and cradle dimensions, keep the display clear of instruments and controls, route charging safely, and confirm the device cannot detach or obstruct steering, airbags or driver visibility.

Fits Vito / Viano / V-Class · W639

Replacement pull handle for the sunroof shade. The creator designed it for the CLS C219 and explicitly reports confirmed E-Class fitment; source images show the physical handle installed. No other roof or trim variant is inferred.

Fits E-Class · W211 / S211

Blank insert for the MP3-button position in the center-console switch panel. The author identifies the exact chassis and supplies the printable geometry, but does not establish applicability to every switch-panel or equipment variant; compare the opening before printing.

Fits E-Class · W211 / S211

Two replacement retaining clips that keep the estate rear seatbelts clear while the seat backs are folded. The creator reports accurate fit and warns that PLA deformed in summer cabin heat; use PETG or a more heat-resistant material.

Fits E-Class · W211 / S211

Left and right plastic recesses that retain the metal mounting points for the estate luggage-compartment protection-net roller on the rear-seat backs. The creator reports a snug fit, recommends PETG with build-plate supports, and notes that the 9 mm bracket holes are intentionally tight.

Fits E-Class · W211 / S211

Storage tray that installs in place of the factory CD changer. The creator specifies ASA or ABS, four walls, five top and bottom layers, and 13% infill.

Fits E-Class · W211 / S211

Four-piece concealed storage compartment installed in place of the factory CD changer and opened with the button below the radio. The source states automatic closing after 30 seconds; wiring and actuator details remain the installer’s responsibility.

Fits E-Class · W211 / S211

Replacement cap for the roof-trim opening. The source includes the printed cap and installed physical views; confirm the opening dimensions and trim variant before installation.

Fits E-Class · W211 / S211

Replacement rear-bumper support bracket corresponding to the exact child number identified by the creator. Print upright with high infill in ABS or polycarbonate-class material, use support only at the latch, and remove the modeled sacrificial support from the screw hole after printing.

Fits E-Class · W211 / S211

Replacement link for the folding center-console cup-holder mechanism. Source photos document the original mechanism, printed part and working assembly; verify smooth movement before reinstalling the trim.

Fits E-Class · W211 / S211

Left and right rosettes for the luggage-compartment side panels around the boot-lid hinge arms. The author reports a perfect fit but instructs users to make a small cut after printing so each rosette can be installed around its arm. Molded child numbers were not independently verified, so no OEM number is assigned.

Fits E-Class · W211 / S211

Exterior rear-window cover for the estate body, replacing the corroded metal cover around the rear-wiper shaft. Bond with automotive glass adhesive or sealing silicone and retain the source-stated estate-only fitment.

Fits E-Class · W211 / S211

Replacement opening handle for the storage compartment below either front seat. Print vertically with support beneath the hinge features and verify hinge movement before loading the compartment.

Fits E-Class · W211 / S211