Find your next part.

Remixed headlamp alignment cup narrowed by 5% and modified to accept both rectangular and round headlamp pins for Alfetta GT, GTV and GTV6 applications. Compare the pin form and adjustment range with the original before installation.

Fits GTV · Alfetta GT / GTV / GTV6 (Tipo 116)

Replacement trim surround for the manual moonroof lever. The creator directly copied an original GTV6 part and notes that these surrounds become brittle with age. The unverified number mentioned by the creator is deliberately not assigned as an OEM association.

Fits GTV · Alfetta GT / GTV / GTV6 (Tipo 116)

Flexible gasket for the exterior door handle of an Alfa Romeo Alfetta sedan. The creator printed it in TPU at 20 mm/s and notes that the current size squeezed on successfully but could possibly be slightly larger; test-seal against the handle and paintwork before final assembly.

Fits Alfetta · Berlina (Tipo 116)

Replacement lateral support for the rear bumper of a 1979 Alfa Romeo Alfetta Berlina. Compare the source geometry with the original side and mounting points before installation; the creator identifies the year but does not state whether the design is left/right-specific.

Fits Alfetta · Berlina (Tipo 116)

Accessory holder for a 250 ml European can in a 1998 Tipo 916 Spider. It mounts through the 12 V socket adapter; the creator notes that one wrap of tape may be needed if the socket fit is loose. The source geometry does not include the photographed laser-marked logo.

Fits Spider · Tipo 916

Two source-provided clip geometries for retaining the windscreen-washer nozzles and hose on Tipo 916 Spider and GTV wiper assemblies. Compare the original clip location and hose routing, then select the matching source variant before installation.

Fits GTV · GTV (Tipo 916) · Spider · Tipo 916

Replacement insert for the B-pillar rubber seal moulding used on Tipo 916 Spider and GTV models. The creator specifies three printed copies per seal assembly, 0.28 mm layers, no supports and 100% infill; print the source file three times and test the rubber-mould engagement before final installation.

Fits GTV · GTV (Tipo 916) · Spider · Tipo 916

Two creator-provided headlight dust-cap variants for driving-light or longer LED-bulb clearance: a closed cap and a version with a 22 mm cable opening. The source explicitly states fitment for Alfa Romeo 159, Brera and Spider. Check bulb heat, cable sealing and cap engagement before use.

Fits 159 · Tipo 939 · Brera · Tipo 939 · Spider · Tipo 939

Replacement bracket for the electrical connectors on the instrument cluster of a 1989 Alfa Romeo Spider. Compare the source images and original bracket before installation; support is required for the source orientation.

Fits Spider · Series 3 (Tipo 115)

Two-hole replacement block for the door area of a classic Spider Duetto. Compare the mounting-hole spacing and installed orientation with the original part before use.

Fits Spider · Series 1 (Tipo 105 / 115)

Replacement flexible cap fitted between the windscreen-wiper arm and retaining nut on 1970s Alfa Romeo Tipo 115 Spiders. Check pivot clearance and secure wiper-arm retention before use.

Fits Spider · Series 2 (Tipo 105 / 115)

Workshop driver for installing the front crankshaft seal in an Alfa Romeo 2.0 L Nord engine. Check the driver's seating face against the new seal and use controlled force; it is an installation tool, not an in-service engine component.

Fits Giulia GT / GTA · Tipo 105 / 115 Coupes

Workshop tool for centering piston rings in an 84 mm cylinder bore while checking end gap. The 84 mm size is corroborated for the Alfa Romeo 2000 GTV's 1,962 cc engine; confirm the measured bore before use.

Fits Giulia GT / GTA · Tipo 105 / 115 Coupes

Workshop fixture that mounts to the six-bolt rear crank flange of an Alfa Romeo 2.0 L Nord engine for controlled rotation during assembly. Print in PETG at full infill as the creator recommends; never use it to start or run an engine.

Fits Giulia GT / GTA · Tipo 105 / 115 Coupes

Workshop alignment tool for the pressure plate and clutch on Alfa Romeo Tipo 115 GTV coupes. Verify pilot and hub diameters against the removed clutch before assembly; this is an installation aid, not an in-service vehicle part.

Fits Giulia GT / GTA · Tipo 105 / 115 Coupes

Two source-provided replacement connector variants for the cabin heater vents in 1970–1976 Alfa Romeo 2000 GTV/unificato Bertone coupes. Compare the original connector and select the matching variant before installation.

Fits Giulia GT / GTA · Tipo 105 / 115 Coupes

Printable repair and alignment jig for rebuilding broken left- or right-side fog-lamp mounting tabs. The creator identifies Giulia and Stelvio fitment and calls for two-part structural plastic adhesive. This is an alignment aid, not a printable lamp or lens.

Fits Giulia · Tipo 952 · Stelvio · Tipo 949

Replacement cover for a lost or broken ISOFIX access-opening flap on 2018-and-later Giulia and Stelvio rear seats. This is non-structural trim and must not obstruct the child-seat anchor.

Fits Giulia · Tipo 952 · Stelvio · Tipo 949

Replacement passenger-side trim cover around the seat-adjustment controls. The creator explicitly identifies Giulia and Stelvio fitment; verify switch clearance before use.

Fits Giulia · Tipo 952 · Stelvio · Tipo 949

Longer and less bulky interior-mirror attachment variant for the creator’s Giulia phone-mount system, providing additional adjustment range.

Fits Giulia · Tipo 952

Adapter for mounting a Sony Xperia Z5 Compact at the interior-mirror location. It is the phone-side companion to the creator’s Giulia mirror attachment.

Fits Giulia · Tipo 952

Replacement actuator finger for the glovebox latch. The creator made it for a Giulia Quadrifoglio after the original plastic actuator failed. Check latch release and retention before closing the glovebox.

Fits Giulia · Tipo 952

Clip for 7.5 mm Lumenition Performance high-tension ignition leads used on Alfa Romeo Tipo 105 cars. Confirm lead diameter, avoid sharp bends, and keep the clip clear of hot or moving engine components.

Fits 1750 / 2000 Berlina · 1750 Berlina (105.48) · 1750 / 2000 Berlina · 2000 Berlina (105.12) · Giulia · Tipo 105 / 115 Berlina +5

Replacement spacer for the speedometer drive where the cable connects on Alfa Romeo Tipo 105 cars. The creator copied an original spacer, printed it in ASA, and reports successful fit and operation.

Fits 1750 / 2000 Berlina · 1750 Berlina (105.48) · 1750 / 2000 Berlina · 2000 Berlina (105.12) · Giulia · Tipo 105 / 115 Berlina +5