Find your next part.

Land Rover Discovery 3 armrest cap.

Fits Discovery · 3 · Range Rover Sport · L320

Adaptor to fit Discovery 2 Cruise Control switch to Defender td5. Quote from SimonRafferty: "It's very easy to add cruise control to any Td5 Land Rover Defender just by adding a couple of wires to the ECU and connecting them to a switch. (search on line for details) Unfortunately, there are no nice looking switches. My solution was to fit a switch from a Td5 Discovery 2 - and print this adaptor so it can easily screw on to the steering column. This is version 2 which is a much better fit and prints in one piece. Use higher temperature filament such as PETG or PAHT - otherwise it will melt in the sun. That's how come V2 came to be! Insert a couple of M4 Nuts into the slots provided, then attach the switch with 2 x M4 x 10mm screws"

Fits Defender · Td5

Clip to hold brake pipes to chassis for Defender TD5. It fits into existing 7mmØ holes in chassis and holds a 5mmØ brake pipe secured by a 4.7mm*1.3mm nylon cable tie. It's designed to be forced into the chassis with a hammer and strongly hold the brake pipe even without beeing secured by the cable tie, but be aware that brake pipes are quite sensible parts of a vehicle and may result to your death if not secured appropriately. Use this part at your own risk and check conditions of the brake pipe clip regularly.

Fits Defender · Td5

Replacement driver door trim window.

Fits 944 · 944

Custom turbo ignition wires holder.

Fits 944 · 944

Replacement back cover roller brackets.

Fits 944 · 944

Two-piece passenger-side interior door-pull conversion with a GT3-like shape. The creator says to mirror the files for the opposite side and attach the pull strap with a small screw.

Fits 911 · 997

Cabin-mounted mobile phone holder designed to accept an added wireless charger.

Fits 911 · 997

Cup holder designed for a 2013 C180 and physically shown in its centre console, with short and long sleeves for 59 mm cans and larger containers. The creator recommends PETG or ABS for cabin heat, supports and roughly 0.16–0.24 mm layers. Match the console and container diameter, check selector and control clearance and use only closed, cool containers until retention is proven; verify the holder cannot loosen or cause a spill under braking.

Fits C-Class · W204 / S204 / C204

Replacement hinge set for both sun visors, developed from a 2003 car and explicitly stated by the creator for 1998–2004 SLK 230, SLK 320 and SLK 32 AMG models. Source photographs show the visor, original and printed hinges loose, and the completed visor installed. The creator used carbon-fibre HTPLA with 2 mm walls, 30% gyroid infill, supports and post-print annealing. Treat the supplied end-hinge files and combined hinge file as a set, compare every original piece, use tough cabin-heat-resistant material, smooth pivot surfaces and verify each visor holds securely without obstructing vision.

Fits SLK / SLC · R170

Four-piece left/right replacement retainer set for the power-seat switch panels, explicitly designed as a direct replacement for a 1990s S420. The source photographs show the physical panel assemblies and installed retainers. Independent mesh inspection found three of the four preserved STLs non-watertight, so repair and validate the sliced geometry before printing. Compare side and switch-panel version before use, print in a tough cabin-heat-resistant material, retain the original fasteners, and verify that the panel is secure without restricting any seat control or trapping wiring.

Fits S-Class · W140 / C140

52mm hub nut socket for a wide range of Land Rover models. Most wheel bearings only need gentle torque - a few later models use the same nut but with huge torque and this likely won't work for those. 1/2" socket plus a 27mm (wheel nut) sized hex on the back. Designed to be printed without supports. Print in something robust.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Discovery · 1 +5

Replacement blanking plate for the center-armrest storage opening after removal of the factory telephone cradle. The creator modeled it for the second-generation X5, shows it physically fitted and states that the friction-fit print replaces BMW cover 51 16 9 115 083 without reproducing the original clips. BMW catalog evidence also lists that cover for the contemporary X6 E71/E72. Confirm the telephone/storage-console configuration and applicable option equipment by VIN, use a heat-resistant material, and verify that the plate remains secure without interfering with adjacent wiring or sockets.

Fits X5 · E70 · X6 · E71 / E72

Clip-on cargo hook for the rear load-area rail, physically shown installed and documented by the creator as used reliably for more than a year. The creator directly lists X3 E83, 3 Series E46, X5 E53 and 5 Series E39 compatibility, so all four live generations are linked. This is an accessory rather than a reproduction of a BMW service part. Print in PETG as documented, observe sensible load limits, and confirm it cannot obstruct the rear seat or cargo cover.

Fits 3 Series · E46 · 5 Series · E39 · X3 · E83 +1

Clutch center tool for BMW M52 (and other) motor This tool is needed to mount and center the clutch, you can't used standard tool. Work perfectly on my 1998 528i e39 Creator reports successful use on a 1998 E39 528i. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Left/right interior mounting pod for adding tweeters in a BMW E28. The photographed print is installed in the car; the opening is intentionally generic, so select a tweeter that fits or design a separate driver adapter. Confirm mirror-image orientation, trim contour, sight lines and airbag-free mounting location before drilling or fastening.

Fits 5 Series · E28

Replacement inner translucent rocker for the BMW E36 power-window switch, physically compared with the original switch. The listed 61318365300 identifies the complete switch assembly, not this printed insert, so no OEM number is assigned. Use heat-resistant translucent material and verify return, illumination and anti-pinch operation.

Fits 3 Series · E36

Fourth-iteration replacement for the small slider-rail clip used in creator-listed E36, E39, E46 and E53 sunroofs. The source shows the physical print and a working demonstration. Use heat-resistant material and verify full sunroof travel, anti-pinch operation and water sealing before driving.

Fits 3 Series · E36 · 3 Series · E46 · 5 Series · E39 +1

Replacement sliding jaw for E30 and E28 sunroof mechanisms, copied from the original and physically compared. The source provides a load-oriented two-piece print option; BMWFans confirms sliding jaw 54121933550. Verify full sunroof travel before road use.

Fits 3 Series · E30 · 5 Series · E28

Low-profile 17 mm ball mount developed for the BMW F20 1 Series center-console side panel. The creator attaches it with double-sided automotive foam tape, shows it installed with a phone holder, and reports no problems in use. Print in ASA, ABS, or another cabin-temperature-resistant material and keep the device clear of controls and driver sight lines.

Fits 1 Series · F20 / F21

Replacement socket-hinge piece for a broken Jeep Renegade sun visor. The creator printed the working part in PETG and documents it installed.

Fits Renegade · BU

Press-fit extender for the Jeep Renegade rear luggage-cover support. It increases engagement so the cover does not fall when the opposite side is being hooked in place.

Fits Renegade · BU

Rigid MOLLE/PALS panel for the 1996–1998 Grand Cherokee ZJ center console. Standard and no-spacer versions are included, with the installation sequence and finished use documented.

Fits Grand Cherokee · ZJ / ZG

Two-piece puller for removing a seized AW4 automatic-transmission neutral-safety switch without prying on it. It uses an M8 nut and bolt to draw the switch from its shaft.

Fits Cherokee / Liberty · XJ