Find your next part.

Two replacement shaft-lock variants for the headlamp-wiper motor assembly: K for SWF motors and L for SWF or Bosch motors. The creator tested both on original assemblies and documents the installed position. Identify the motor maker before printing, use heat- and weather-resistant material, preserve cable potting, and bench-test motor retention, full sweep and parking before road use.

Fits E-Class · W124 / S124 / C124 / A124

Direct replacement for the lower condenser mounting grommet identified by the creator as A2019970381. The source model intentionally simplifies fillets and tightens the fit for printing. Compare the original grommet and condenser pin, use heat-, weather- and vibration-resistant flexible material, and confirm the condenser is retained without metal-to-metal contact or stressed refrigerant lines.

Fits E-Class · W124 / S124 / C124 / A124

Replacement clip used in pairs to secure the lower engine wiring harness to the engine block; the creator notes that the same size also appears elsewhere. Exact routing varies with engine and model year, so compare the original clip and mounting point rather than inferring other positions. Use engine-bay heat-, oil- and vibration-resistant insulating material, avoid sharp wire contact and confirm the harness cannot reach hot or moving parts.

Fits E-Class · W124 / S124 / C124 / A124

Insert replacing the disassembled centre-console fader-switch mechanism to retain a USB extension cable from an updated head unit. The source supplies the insert model and console-fit imagery but no electrical hardware. Confirm the early console opening and cable connector, use cabin-heat-resistant insulating material, provide strain relief and fusing for the connected accessory, and keep wiring clear of the selector and original harness.

Fits E-Class · W124 / S124 / C124 / A124

Replacement grip for the thin wallet/spare key, designed to make the original key blade easier to turn. The print is only the external grip and does not reproduce the lock blade. Confirm the blade shoulder and grip fit, use tough cabin-heat-resistant material, retain the blade securely, and test gentle operation in each intended lock without forcing the cylinder.

Fits 190 Series · W201

Replacement covering/clip for retaining the vapour barrier behind the interior door panel. The creator explicitly identifies both 190-series and 124-series applications, supplies numbered and unnumbered geometry, and recommends glass-fibre-reinforced polypropylene with controlled support separation. The controlled material taxonomy does not include that polymer; nylon is listed only as a durable alternative and requires fit validation. EPC applicability maps the exact covering to both chassis families. Match the original profile, avoid tearing the moisture barrier, and confirm the door panel seats without bulging.

Fits 190 Series · W201 · E-Class · W124 / S124 / C124 / A124

Replacement plastic support panel beneath the wooden centre-console switch trim. The creator reports that the design works but may require sanding. Compare the switch layout and console version before printing, use cabin-heat-resistant material, deburr all openings, and confirm switches, wiring and the selector remain unobstructed.

Fits 190 Series · W201

Custom dashboard air-vent adapter for a standard 52 mm temperature, voltage, oil-pressure or lambda gauge. The creator explicitly states fitment to both 190-series and 124-series vents. Confirm steering-side vent geometry, gauge depth, wiring and hose routing; fuse electrical additions, avoid sharp edges and preserve driver visibility and remaining ventilation.

Fits 190 Series · W201 · E-Class · W124 / S124 / C124 / A124

Two-piece replacement shaft set for the mechanical speedometer drive. The creator printed it in PETG with a 0.2 mm nozzle, reports about 1,500 km of successful use, and notes that axle sanding may be required. The cited EPC number describes the complete speedometer-drive component and is not assigned to these printed internal pieces. Match the transmission drive version, avoid altering tooth geometry, and verify accurate speed indication and leak-free operation.

Fits 190 Series · W201

Replacement handle modeled after the original bonnet-release handle. Source photographs document the latch area and installed handle location. Compare the pivot and cable-end geometry, use tough cabin-heat-resistant material, preserve full cable travel, and verify the bonnet opens, closes and latches correctly before driving.

Fits 190 Series · W201

Replacement driver-side dashboard vent surround, supplied as both a complete model and a two-piece version for easier printing. The creator reports that it fitted but was not fully refined, warns that PLA deformed in summer heat, and says to mirror the part for left-hand-drive use. The complete STL appears about 25.4 times smaller than the split files when interpreted as millimetres, so verify source units and final dimensions in the slicer. Confirm steering side and vent geometry, print in heat-resistant material, and verify free vent-slider movement.

Fits 190 Series · W201

Replacement cap for a broken cabin-blower control switch, modeled from the original for a 190-series interior. The source provides comparison imagery but no long-term validation details. Compare the switch shaft and detents, use tough cabin-heat-resistant material, and verify every blower position operates and the cap cannot bind against the panel.

Fits 190 Series · W201

Replacement angle bracket connecting the centre-console panel to the transmission-tunnel covering on earlier cars. The creator copied the broken original, identifies EPC position 44, and states that the original threaded insert and screw are reused. Confirm early-model console geometry, use tough cabin-heat-resistant material, and tighten only enough to retain the trim without cracking the bracket.

Fits 190 Series · W201

Adapter ring for fitting an Alpine SXE-1025S speaker to the original dashboard mounting points while retaining the original grille. Fitment evidence is specific to that speaker model. Check depth, terminals and grille clearance, use cabin-heat-resistant material, protect the dashboard and wiring, and secure the speaker so it cannot rattle or detach.

Fits 190 Series · W201

Service adapter for manually operating the sunroof emergency drive, with the vehicle-side internal profile and an external profile for a 13 mm socket. Confirm the drive version and engagement depth before use, choose tough material, turn only with controlled hand force, and stop if the roof binds; this adapter is not a substitute for correcting the underlying drive or cable fault.

Fits 190 Series · W201

Replacement control knob for a Blaupunkt Boston radio installed in a 190-series dashboard. Source photographs show the radio and control position but do not establish fitment to other Blaupunkt variants. Compare the shaft profile and adjacent control clearance, use cabin-heat-resistant material, and confirm the knob operates smoothly without contacting the faceplate.

Fits 190 Series · W201

Custom adapter frame for the specific 7-inch double-DIN Android head unit linked by the creator. Source photographs show the printed frame and the modified centre-console opening. Confirm the radio dimensions and console cut-out before printing, protect the veneer and wiring, provide adequate ventilation and strain relief, and do not assume other double-DIN units share the same bezel geometry.

Fits 190 Series · W201

Replacement storage cubby for the obsolete cassette-changer opening below the radio. The source correction identifies 190-series fitment, and photographs show the printed ABS cubby and its installed position. Use cabin-heat-resistant material, check radio and console clearances, retain wiring safely behind the opening, and keep stored objects clear of the selector and controls.

Fits 190 Series · W201

Blanking cover for an unused rectangular switch opening in the upper centre dashboard trim. The creator designed and physically fitted it in a 190-series cabin but does not claim other applications. Compare the opening and surrounding veneer before printing, use cabin-heat-resistant material, and verify the cover cannot interfere with the adjacent rear-window-demister switch or air vent.

Fits 190 Series · W201

One-to-one copy of an original 126-series side-skirt fastener, printed by the creator in PETG with 0.1 mm layers, organic supports and four perimeters. Source photographs show the loose clip beside the original and the relevant body-cladding locations. W126 cladding uses several position-specific fasteners, so compare the original clip before use, deburr contact edges and confirm the panel is retained without distortion.

Fits S-Class · W126 / C126

Driver- and passenger-side replacement lever files for a 126-series electrical seat switch. The source identifies the function and fitment but provides only a photograph of the original child component, not a printed installation. Compare the switch version, shaft and lever direction exactly, use tough cabin-heat-resistant material, and verify every seat movement stops on release without a lever sticking or fouling the trim.

Fits S-Class · W126 / C126

Replacement 12-tooth drive pinion demonstrated in an Australian-compliance 1989 560 SEC instrument cluster. The creator printed, fitted and updated the gear profile after road use, and reports continued odometer operation. Fitment is restricted to a matching 12-tooth cluster; do not assume every 126-series speedometer uses it. Support the rotor shaft during press-fitting, preserve end float, have any desoldering performed competently, and verify accurate speed and distance readings before road use.

Fits S-Class · W126 / C126

Spacer ring developed to retain a near-match replacement dust boot on a 126-series rear self-leveling-suspension hydraulic strut when the original boot is unavailable. Source photographs show the physical ring and boot installation. This is a protective-boot adapter only, not a suspension load path. Match the replacement boot and strut dimensions, use oil-, weather- and fatigue-resistant material, and inspect hydraulic lines, clearance, leaks and boot retention before returning the car to service.

Fits S-Class · W126 / C126

Replacement plastic trim panel surrounding the bonnet-release lever on a 300SD. Only the creator's revised R2 file is included; it raises the screw bosses and shortens the shoulders after the first version did not sit flat. The creator explicitly says it does not fit a 123-series car. Use heat-resistant material, retain the original fasteners, and confirm the panel sits flat without restricting full release-lever travel or bonnet-latch operation.

Fits S-Class · W126 / C126