The parts catalog
Find your fit. Download a free file or choose a maker to print and ship your part.
2,661 matching parts
Free files. Made for your car.
C3D–01975Replacement shaft for the instrument-cluster trip and dimmer controls, measured from an OEM stalk. The creator recommends resin or ABS for resolution and heat resistance and notes that sanding may be needed for a close fit.
Fits 911 · 996 · Boxster · 986
C3D–01974Ashtray-mounted phone stand with a USB cable pass-through for an adhesive magnetic charging puck, designed by Trogdor4Ever for the Cayenne 958 center console. The creator printed it in PLA+ and added neoprene foam to the lower corners for a snugger fit.
Fits Cayenne · E2 (958)
C3D–01973Printable lining for a center-console-delete conversion, supplied as a full model or front/rear split for a Prusa Mk3S-size bed, plus a cover plate. The creator recommends PETG, instructs removal of the orange bracket tabs for mounting, and leaves room to upholster the part.
Fits Boxster · 986
C3D–01972Center-console phone mount based on the creator's 3D scan, with versions for iSetchi and Apple MagSafe chargers. The creator reports months of in-car use and says the Apple charger must be attached with double-sided tape or glue.
Fits Taycan · J1
C3D–01971Three-part clip-in center-console coin tray that replaces the ashtray. The creator directs users to slide the parts together, glue the seams, and apply fabric tape at the sides to improve fit and reduce rattles.
Fits 944 · 944
C3D–01969One-piece phone-holder mount for the stock stereo with an approximately 17 mm ball. The creator says it worked with an existing holder and used foam tape beneath the ball to reduce bounce.
Fits Boxster · 986
C3D–01968Vent-wall clamp with an integrated one-inch ball for accessory or phone-mount arms. It expands against the vent walls with two M5 x 18 mm tensioning screws and uses 1/16-inch rubber sheet for grip and trim protection.
Fits Panamera · G1 (970)
C3D–01967Cap for unused headlight-washer openings in Turbo and S2-style front bumpers.
Fits 944 · 944
C3D–01966Plastic clip that holds the fuel rail to the engine-bay firewall, modeled against an original clip.
Fits 914 · 914
C3D–01965Two-piece bracket that mounts a remote clutch bleed-screw assembly to the fan shroud. It is sized for a -3 AN bulkhead mount accepting a 3/8-24 bleeder screw and uses a removable end plate so the clutch line can be slid into place without disconnecting it.
Fits 911 · 993
C3D–01964Split-ring cap for the upper HVAC blend-door post, installed through the front-luggage-compartment access opening and secured with a small dab of superglue while keeping adhesive off the slotted plastic bearing.
Fits Boxster · 986
C3D–01962Clip-on base for the left edge of the center console that carries an Apple MagSafe charging puck or another magnetic phone holder.
Fits Taycan · J1
C3D–01960Replacement collar stop for the hand-throttle rod, upgraded with two M3 set-screw holes that must be tapped after printing.
Fits 911 · Original (901/911)
C3D–01959Right-rear guide that receives the electric sunroof lifting arm and raises the roof. The creator reports that right and left guides restored operation on a 1984 car and says the opposite side can be produced by mirroring this model.
Fits 944 · 944
C3D–01958Two-piece center-console cupholder replacement designed 1 mm smaller than the stock console to allow vinyl wrapping. The creator plastic-welded the pieces, wrapped the assembly in vinyl, and supplied printable inserts plus a logo stencil.
Fits 944 · 944
C3D–01957Removable dual cup-holder assembly whose bracket wedges between the center dashboard and upper center console. The cup holders can be stored in the armrest when not in use.
Fits Boxster · 986
C3D–01956Center-console tray remix for an iPhone 13 Pro and Anker 15W PowerWave Alloy charging pad, with added phone-positioning blocks and a lower cutout to clear the flip-up cover. It installs after removing the factory rubber liner.
Fits 911 · 991 · Boxster · 981 · Cayman · 981
C3D–01955Passenger/right headlight-washer cover with tabs and a companion jig used to heat-form the cover to the compound curve against the headlight housing.
Fits 911 · 996
C3D–01954Five snap-in inserts for the dashboard vent openings that hold recovered vinyl around the holes without glue. The creator says they snap into place and prints them in ABS.
Fits 944 · 944
C3D–01953Support clip for the 997 front-bumper mesh and slats. The supplied version 2 STL is smaller and more concealed than the photographed version 1; use 3 mm cable ties and two clips per side.
Fits 911 · 997
C3D–01952Three printable shift-linkage repair inserts designed for a 1997 five-speed car. The creator specifies PETG or ABS, no supports, 40% infill and 2 mm walls, and reports positive initial road-test results.
Fits Boxster · 986
C3D–01951Two-piece iPhone 12 Pro Max support that replaces the CD-storage function while retaining the original surround; the two printed modules assemble with three M3 x 10 screws.
Fits Boxster · 986
C3D–01950Replacement retaining pin and small gear for the dashboard cup-holder mechanism. The creator thickened the pin for easier printing, increased the gear height for better mesh, and used an 18-gauge brad nail as the pivot. The parts were printed in PETG after PLA softened in a hot car.
Fits Boxster · 987 · Cayman · 987
C3D–01948Replacement flap for the fresh-air blower housing. The creator used a 4 mm foam-rubber seal and PETG for the heat encountered during cabin heating.
Fits 911 · G Model