Find your next part.

Replacement access cover for the oil-drain opening in the engine-compartment underbody screening, physically shown loose and installed by the creator. BMW catalogs identify this child cover as 51757261712, item 5 in the underhood-shield diagram; it is used on X3 F25 and X4 F26 applications, so both live generations are linked. The printed design uses lower U-nuts and hex screws rather than the original fastening method. Print in PETG or a higher-temperature engineering polymer, confirm the panel variant and VIN, and verify secure retention and clearance before driving.

Fits X3 · F25 · X4 · F26

Replacement retaining ring for a loose center-console cigarette-lighter socket, supplied with multiple loose, installation and in-use physical views for an X3 E83. BMW catalog socket-mount and illuminated-ring numbers vary by location and production date, and the source does not identify which original child component this geometry reproduces, so no number is assigned. Use a heat-resistant material and verify electrical isolation, secure socket retention and plug clearance before use.

Fits X3 · E83

Left and center replacement tabs for the movable dashboard air vents, modeled from the creator's 2007 X3 E83 and physically shown beside original vent tabs. The small movable tabs are not separately serviced by BMW; complete fresh-air grille numbers vary by position and production date, so no parent assembly number is assigned. Print in a cabin-heat-resistant material and verify smooth louver movement without rattle or binding.

Fits X3 · E83

Two-piece bolted replacement for missing metal staples that retain the lower-windscreen rain tray, with loose and installed physical evidence. The source's 51713401811 identifies the complete E83 windscreen-panel cover, while the printed geometry replaces its mounting feature, so that parent number is not assigned. Use a weather- and heat-resistant material, corrosion-resistant M5 hardware, and verify wiper clearance, water drainage and retention after installation.

Fits X3 · E83

Slide-on repair for a broken latch on the low-beam rear headlight dust cover, directly modeled and fit-tested by the creator for X3 E83 headlights. Molded marking 1305239123 is not an 11-digit BMW number; catalog number 63128381326 identifies the complete dust cover, not this printed latch repair, so it is deliberately withheld. Print in PETG or a higher-temperature engineering polymer and verify the cover remains sealed and removable after heat cycling.

Fits X3 · E83

Replacement plus/minus volume rocker modeled after the creator's broken multifunction steering-wheel button and physically shown loose and installed. The creator documents direct fitment to X3 E83 and X5 E53. BMW services the surrounding switch assembly rather than this printed child button separately, so no parent assembly number is assigned. Use a durable heat-resistant material, preserve free button travel, and verify all steering-wheel controls operate without sticking before driving.

Fits X3 · E83 · X5 · E53

Replacement cover for a luggage-compartment child-restraint anchor, physically shown installed by the creator in a 2010 X3 E83. BMW catalogs identify the anthracite/black cover as 51473405879, item 12 with three per vehicle; grey 51473418987 and sand-beige 51473418986 are distinct trim variants and are not assigned. Confirm the interior color and VIN, and verify the cover clips securely without obstructing access to the restraint anchor.

Fits X3 · E83

Six-coin organizer sized for the front ashtray insert and physically tested by the creator in an X3 E83. It also retains the plastic cap from the rear lighter socket. This is an aftermarket accessory, so no BMW ashtray or console parent number is assigned. Use a cabin-heat-resistant material, confirm the insert is bonded securely as documented, and verify it does not obstruct the lighter socket or ashtray closure.

Fits X3 · E83

Two-piece storage mount for the portable Flexible Fast Charger documented with the first-generation iX3: a wall plate retained by three 4.5 mm screw holes and a case-side bracket retained by two M4 x 12 fasteners. The creator printed and physically installed the set, and supplies separate watertight STL files. Verify the pictured charger housing and mounting-hole dimensions before printing because portable charger hardware varies by market and revision. Print vertically with four perimeters as documented, use PETG or another durable heat-resistant material, anchor into a suitable wall substrate, and confirm the charger and cable cannot fall, overheat, abrade, or strain electrical connections.

Fits iX3 · G08

Center-console phone mount sized for an ESR Mini Qi2 charger, with a 58.9 mm diameter and 7.5 mm deep puck recess. The creator documents the printed mount installed in the vehicle and supplies both printable STL and editable STEP files. Verify the pictured console, exact charger revision and phone/case clearance before printing; use a heat-resistant material and ensure the charger, cable and phone cannot obstruct the vehicle controls or overheat.

Fits iX · I20

Angled MagSafe phone mount that press-fits into the factory center-console phone tray and turns the phone toward the driver. The creator's source image shows the printed part installed with a phone attached. Verify the pictured console, viewing angle, MagSafe puck and phone/case dimensions before printing; use a heat-resistant material and ensure the phone remains secure without obstructing the controller, selector, buttons or driving visibility.

Fits iX · I20

Center-console holder for a Samsung Galaxy Fold that locks into the factory phone-tray opening to resist tipping under acceleration. The creator's source image shows the printed holder installed in the vehicle with the phone open and in use. Verify the pictured console and your phone/case dimensions before printing; use a heat-resistant material and confirm that the holder cannot interfere with the controller, selector, buttons or safe driving visibility.

Fits iX · I20

Press-fit MagSafe phone mount for the factory center-console phone tray. The original creator designed, printed and installed it in an iX, and documents the installed fit with an iPhone 13 Pro Max in an Apple case. The main mount may be used alone for a wide cased phone or with the supplied left and right side guides. Verify the pictured console tray and MagSafe puck dimensions before printing; use a heat-resistant material, preserve access to all controls, and confirm the phone remains secure without obstructing driving controls.

Fits iX · I20

Replacement width-adjustment clip that lets larger modern phones, including phones in protective cases, fit the factory snap-in wireless charger. The creator designed, printed and installed it in a 2019 Roadster and documents removal, installation and the completed fit. Compatibility is limited to cars equipped with the pictured snap-in charger; verify the installed charger and clearances before printing. Use a heat-resistant material, print at the documented 45-degree orientation, and do not allow the phone or charger to obstruct controls or overheat.

Fits i8 · I12 / I15

Dashboard adapter that clips beneath the center-vent trim and provides two slots for attaching an accessory holder that would otherwise clamp directly to a vent grille. The creator shows the printed adapter installed by itself and carrying a physical magnetic phone holder, and notes that optional automotive-grade double-sided tape improves retention. This is a removable accessory rather than an original BMW component, so no OEM number is assigned. Use cabin-heat-resistant material, protect the adjacent trim, verify secure attachment and confirm that the holder, cable and device do not obstruct controls, displays, airflow or the driver's view.

Fits i5 · G60 / G61

Center-armrest organizer with a 15 mm vertical phone slot, a 7 mm cable passage, separate cable storage, a general compartment, and a small raised area for keys. The creator shows the physical organizer installed loaded and empty and explicitly identifies compatibility with G22, G23, G26, and i4 interiors. Use ASA, ABS, or another cabin-heat-resistant material as recommended; verify stable seating, phone and cable clearance, and unobstructed armrest movement.

Fits 4 Series · G22 / G23 / G26 / G82 / G83 · i4 · G26

Flexible protective case for the vehicle remote key, with open access to all buttons and the key-ring eye. The creator shows the TPU case fitted to the physical key from both sides and provides useful CAD views of the openings. Print in TPU as specified, confirm every control moves freely and the emergency-key release remains accessible, and verify that the case cannot press buttons unintentionally.

Fits i4 · G26

Large center-console storage bin that replaces the original cupholder after the cupholder and its USB and 12 V connections are removed. The creator scanned the exposed recess, shows the printed bin installed, and includes a separate flexible floor liner. This is a deliberate accessory conversion, not an equivalent reproduction of the powered cupholder assembly, so no cupholder or console parent number is assigned. Use cabin-heat-resistant rigid material for the bin and TPU for the optional liner; disconnect and secure the original electrical connectors safely, preserve the mounting screws, and verify stable installation and full console-cover clearance.

Fits i4 · G26

Forty-millimeter funnel shaped for the windshield-washer filler opening. The creator shows the physical funnel seated in the fill neck from two angles and designed it to print support-free with the larger end upward. This is a service accessory rather than the reservoir, filler neck, or cap, so no parent component number is assigned. Confirm the neck fit before pouring and keep debris and incompatible fluids out of the washer system.

Fits i4 · G26

Cup-position insert shaped for a Hörmann garage-door remote. The creator shows the remote seated in the printed insert in the center console and provides an improved version 1.0 with a deeper pocket and reduced five-degree angle; only that revised model is retained. This is device-specific accessory geometry rather than an original BMW component. Use a cabin-heat-resistant material, confirm the remote and insert remain secure, and verify that neither interferes with the cup positions, console cover, controls, or driving.

Fits i4 · G26

Pair of compact brackets for hanging a JBL BassPro Nano under the rear-seat frame where the optional amplifier is not installed. The creator printed two in PETG at 50% infill, fastened them with the subwoofer's original screws, and shows the installed unit and bracket locations. Confirm the vehicle lacks the conflicting amplifier, protect wiring, use thread-safe fasteners, and verify seat movement, ventilation and secure retention before driving.

Fits i3 · I01

Anti-tip adapter for the source-linked small espresso cup, shaped for the center-console cup position. The creator shows the physical adapter seated in the vehicle and with the matching cup. Print in PETG, ABS or another cabin-heat-resistant material, verify both the cup and console fit, and keep hot liquids securely contained and clear of controls while the vehicle is moving.

Fits i3 · I01

Tool set for I01 outer-door-panel hardware: a deep and standard adjustment-element wrench plus seven clip-saver sizes for printer-tolerance matching. The creator shows the physical tools on the relevant clip and explains that the saver may recover clips that survive warm-weather panel removal. Numbers 51007355279 and 51007378101 identify the serviced clip and adjustment element, not these printed tools, so neither is assigned. Do not reuse cracked or distorted one-time clips; verify panel alignment and secure retention after service.

Fits i3 · I01

Three-piece key-fob box with a separate insert, bottom and lid, designed to prevent accidental button presses while carried in a pocket. The source shows the complete physical case closed, open and holding the I01 key fob. This is a protective accessory rather than the key housing itself. Check that the fob fits without continuously loading any button and that the lid remains secure during normal carrying.

Fits i3 · I01