Find your next part.

A printable cup-holder storage cup documented by the original creator for 2020 Corolla Toyota Corolla fitment. Optional hooks for keys/garage remote.

Fits Corolla · 12th Gen

Three-piece 12-volt inspection-lamp socket adaptation using standard 4 mm RC bullet connectors, 14 AWG silicone wire, and an M3 x 12 mm fastener.

Fits Series · 1 · Series · 2

Eleven thickness variants of the isolating shim fitted between the chassis brackets and rear tub to separate dissimilar metals.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +5

Simple cab hook for retaining a loose seat belt when it is not in use. Confirm the mounting position and belt clearance before drilling or attaching it.

Fits Series · 3

Replacement plastic control for the Lucas wash/wipe switch. The sacrificial lower support can be removed after printing

Fits Series · 3

Replacement adjuster for the rear seat. Includes the original version and a revised version that prints without supports

Fits Discovery · 3

Trim Clip for Fuse Box Cover on Defender from 2007 Onwards

Fits Defender · Puma

Replacement air condition knobs.

Fits 944 · 944

Replacement electric sunroof latch.

Fits 924 · 924 · 944 · 944

Replacement lower retaining clip for the front-seat back panel.

Fits Cayenne · E1 (955 / 957)

Replacement side mounting rail for the HEREGOES Android head unit that replaces the factory CDR30 or CDR24 stereo. V2 uses slightly oblong holes for fit adjustment.

Fits 911 · 997 · Boxster · 987 · Cayman · 987

Two-piece hinged locking mechanism for the removable sunroof, with holes for a steel hinge pin.

Fits 944 · 944

Flywheel-bolt-driven installation tool that seats the rear main seal 13 mm below the crank flange; its orientation relief clears the flywheel-flange rivet.

Fits 911 · 996 · Boxster · 986

Lower movable mounting bracket for an Alfa Romeo Stelvio headlight, designed as an alternative to the complete headlamp repair kit.

Fits Stelvio · Tipo 949

Two alternative bases for attaching an aftermarket ball-joint phone holder between the circular dashboard vents. The creator explicitly designed the geometry for the 213/238-series E-Class vent arrangement and shows the adhesive version installed. The second version is intended to engage the vent slots without adhesive, but the creator states that this version was not tested and warns against PLA because it may break during installation. Use a cabin-heat-resistant material, verify adhesive or clip retention before driving, and keep the device clear of controls, airbags and the driver's view.

Fits E-Class · W213 / S213 / C238 / A238

Cupholder-mounted phone cradle designed for a GLC 300 and sized for a Samsung Galaxy A51 in a folding case. Openings in the body are intended to improve phone-audio output. Fit depends on the stated phone and case envelope; verify the cradle seats fully, retains the phone during driving, remains clear of the selector and controls, and does not soften or crack in cabin heat.

Fits GLK / GLC · X253 / C253

Clip-on rear-camera mount developed for the estate headliner and a Vantrue N4/N5 RC-01 rear camera. It clamps between the headliner and roof sheet without screws or holes and is shown installed clear of the tailgate. Fitment is limited to the estate body. Protect the headliner, keep the camera and cable clear of airbags, visibility and tailgate travel, and verify the mount cannot detach.

Fits C-Class · W205 / S205 / C205 / A205

Two cupholder inserts sized for 250 ml and 355 ml energy-drink cans. The creator explicitly states fitment across the sedan, estate, coupé, and cabriolet body variants and provides physical in-console images. Use a heat-resistant interior material, confirm the chosen insert seats fully, keep liquids clear of electrical controls, and stop use if the can can tip, bind, or interfere with the console lid.

Fits C-Class · W205 / S205 / C205 / A205

Direct-replacement manual seat adjustment handles supplied as separate left- and right-hand files. The creator designed them for a 2007 vehicle and identifies the right-hand component as original part A1699190661; Mercedes genuine-parts and PartSouq listings corroborate that number as the right-side seat-adjustment lever. The OEM number applies to the right-hand file only. Use a tough, heat-resistant material, compare the mounting socket and travel with an intact handle, and verify that the seat locks positively in every tested position before driving.

Fits A-Class · W169

Two-piece retaining clip for the driver's floor mat. The creator designed and tested it on a 2011 vehicle, states that the two halves permanently snap together through the mat, and notes that removal from the floor takes slightly more force than the original. The source print used PLA with a 0.4 mm nozzle, no raft and no supports; for sustained cabin heat, prefer an automotive-temperature-capable material. Confirm that both halves are fully locked, that the mat cannot slide toward the pedals, and stop using the print if it loosens or cracks.

Fits A-Class · W169

Larger closed bottle holder derived from the center-console attachment dimensions of the creator-cited cup-holder design. It is intended for large bottles and can also serve as a small waste bin; fitment is limited to the source-stated center-console arrangement.

Fits E-Class · W211 / S211

Replacement pull clip for the factory rear side-window sunshade. The creator modeled it from the factory design, reports direct fit without modification, and recommends ABS or PETG with 0.2 mm layers and 100% infill for cabin heat resistance.

Fits E-Class · W211 / S211

Front-position exterior cover for the side-skirt jacking opening, published for the CLK 208-series and shown installed on the creator's photographed coupe trim. Print vertically with supports and three wall lines to strengthen the hooks, using ABS or a similarly suitable material as the creator recommends. The source does not identify side, facelift, AMG/standard trim, option code or an exact molded number; compare the original opening and retainers before use. No OEM number is inferred from the cover's location.

Fits CLK · C208 / A208

Replacement headliner cap for the emergency retractable-roof lock, explicitly identified for 1997–2004 SLK 230 Kompressor cars. The source image shows the physical cap installed; the creator recommends high-temperature PLA or PETG and reports a FILACUBE HT-PLA print survived Texas cabin heat with little distortion. Match the access opening, use cabin-heat-resistant material and confirm the cap stays secure while remaining removable for emergency roof operation.

Fits SLK / SLC · R170