Find your next part.

Four-piece concealed storage compartment installed in place of the factory CD changer and opened with the button below the radio. The source states automatic closing after 30 seconds; wiring and actuator details remain the installer’s responsibility.

Fits E-Class · W211 / S211

Replacement cap for the roof-trim opening. The source includes the printed cap and installed physical views; confirm the opening dimensions and trim variant before installation.

Fits E-Class · W211 / S211

Replacement rear-bumper support bracket corresponding to the exact child number identified by the creator. Print upright with high infill in ABS or polycarbonate-class material, use support only at the latch, and remove the modeled sacrificial support from the screw hole after printing.

Fits E-Class · W211 / S211

Three-piece installation frame for a nine-inch Android head unit. The author describes it as functional but imperfect and requiring finishing; join all three parts as shown by the source and check secure retention before driving.

Fits E-Class · W211 / S211

Replacement for the break-prone plastic part inside the center armrest, with holes for the factory screws. Verify screw seating and free hinge movement before use.

Fits E-Class · W211 / S211

Replacement connector gear for the factory CD changer opening arm. The source documents the failed original and the printed replacement; confirm tooth engagement before closing the changer mechanism.

Fits E-Class · W211 / S211

Flexible insert for the damper on the estate luggage-compartment floor. The creator reports that it seats well and works; use flexible TPU and verify the damper-end dimensions before installation.

Fits E-Class · W211 / S211

Replacement clip for the footwell storage net. The source provides a physical installed-net image and a printed sample; no other model or side is inferred.

Fits E-Class · W211 / S211

Straight and bent replacement variants for the left rear bumper retaining clip. Fitment is limited to the creator-stated chassis and side; no opposite-side or facelift applicability is inferred.

Fits E-Class · W211 / S211

Cup holder that clips to the right side of the center console through the open cigarette-lighter door. The author designed it for 2003–2008 vehicles and recommends printing the version 3 upside-down STL as one piece; the parametric and split alternatives are retained.

Fits E-Class · W211 / S211

Replacement retaining clip for the luggage-compartment upholstery. The creator identifies the application as the CLK 209 series and describes the model specifically as a trunk-upholstery clip. No side, body-style, market, steering-side, engine, facelift, trim or option-code extension is claimed beyond the source-backed C209/A209 generation.

Fits CLK · C209 / A209

Two-piece phone holder and charging-cable bracket for the CLK 209 series, source-tagged by the creator for W209. The holder clips between the center-console side wall and the climate-control panel, accepts an iPhone 6, 7 or 8, and locates a Baseus charging cable so the phone charges when inserted. The creator explicitly warns against ordinary PLA because it can melt in a hot cabin. Fitment is not extended beyond C209/A209.

Fits CLK · C209 / A209

Replacement rear registration-plate lamp lens for the CLK 209 series. The creator supplies two verified author models: one version retains legs for the festoon bulb and one omits those legs. Print in clear filament; the creator recommends PETG rather than PLA for improved heat and weather resistance, a 0.2 mm translucent window, and silicone sealant around the rim to prevent water ingress. Fitment is source-backed only for the C209/A209 generation.

Fits CLK · C209 / A209

Replacement folding-roof flap and repair-hinge geometry for a broken small roof flap. The creator designed new hinges that attach to the retained original corner piece because the flap was not separately available, and provides three author STLs plus physical source photographs. Exact model-year, side, facelift and roof-option splits are not stated. Compare the original flap, corner piece and hinge clearances before printing; use UV-, weather- and cabin-heat-resistant tough material, deburr every edge, and cycle the folding roof stationary through its full travel while checking that the flap closes, latches and clears seals and adjacent panels. Stop use if any part binds, cracks or loosens; this repair does not replace the roof lock, hydraulic drive or structural linkage.

Fits SL · R230

Reinforced black and white replacement clips for the sedan roof trim, designed to remain compatible with each other and with the original parts. The creator identifies exact child number A2036900013; Mercedes official and PartSouq evidence corroborates it as the W203 roof-moulding retaining clamp. Print both clips upright in heat-resistant material, verify sedan body and trim position, fit without forcing the roof strip and confirm secure retention and unobstructed drainage.

Fits C-Class · W203 / S203 / CL203

Protective cap for an exposed windshield-wiper pivot bolt, shown installed by the creator and intended for PETG. The source gives no side, market or wiper-system revision. Compare the pivot and cowl clearance, use UV-, weather- and engine-bay-heat-resistant material and verify the cap cannot contact the moving arm, trap water or detach into the wiper mechanism.

Fits C-Class · W203 / S203 / CL203

Replacement cover for the 12-volt outlet in the luggage compartment, created after the original lid broke. The source shows the physical closed cover and socket and recommends PETG with 35% infill. Compare the outlet bezel and hinge, use flame- and cabin-heat-resistant material, keep the socket clean and insulated and verify the cover cannot break off, enter the socket or obstruct plug removal.

Fits C-Class · W203 / S203 / CL203

Protective cap for the exposed upper shock-absorber bolt, shown installed by the creator and printed in PETG to tolerate engine-bay heat. The source gives no suspension variant, bolt dimensions or OEM reference. Compare the bolt and surrounding travel envelope, use engine-bay heat-, fluid- and vibration-resistant material and verify the cap cannot loosen, trap corrosive moisture or interfere with suspension inspection or service.

Fits C-Class · W203 / S203 / CL203

Replacement temperature-control dial using the original mount, with creator-stated W203 and W209 fitment and anchor variants for C220, C230 and C240 controls. The creator explicitly warns against PLA because cabin heat can warp it and recommends PETG or ABS. Compare the original shaft and control-panel version, retain the visible temperature reference and verify full smooth travel without binding before driving.

Fits C-Class · W203 / S203 / CL203 · CLK · C209 / A209

Transparent registration-lamp insert with a mount for the compact CVBS/AHD camera commonly supplied with aftermarket head units. The creator explicitly states W203 and W209 fitment and recommends transparent PCTG or PETG, aligned 100% infill, no top or bottom layers and ironing. Compare the lamp opening and camera body, seal cable entries, preserve required plate illumination and verify the insert cannot detach or leak into the boot lid.

Fits C-Class · W203 / S203 / CL203 · CLK · C209 / A209

Replacement door-panel clip published specifically for this generation. The creator recommends printing it sideways with tree supports for greater strength and supplies one 3MF plus a physical source image. Compare the original clip, door socket and trim thickness, use a tough cabin-heat-resistant material, remove support marks and fit without forcing brittle trim or damaging wiring; confirm the panel is fully retained.

Fits C-Class · W203 / S203 / CL203

CD-slot phone-mount base for the APS 50 navigation unit, with a 17 mm ball and physical installed photographs. The phone clamp is not included. Match the head unit and ball socket, use cabin-heat-resistant material, insert without forcing the disc mechanism and confirm the complete mount cannot obstruct controls, airbags or sight lines or detach under braking.

Fits C-Class · W203 / S203 / CL203

Three-part retaining system for luggage-compartment trim: a 5 mm-hole clip plus either a screw-style or pull-style centre pin. The creator printed the parts upright in PETG with a brim and prefers the pull-pin version for removal. Compare the body holes and original trim thickness, use tough cabin-heat-resistant material, deburr the pins and verify every panel is retained without damaging wiring or sharp body edges.

Fits C-Class · W203 / S203 / CL203

Left- and right-hand hooks for the front panoramic-roof sunblind, with physical prints shown by the creator. The source states CLC and W203/W204 fitment and recommends 0.2 mm layers, 100% infill and supports, but gives no production break or roof option code. Compare both original hooks and roof system before printing, use UV- and cabin-heat-resistant material and verify smooth blind travel with no loose part near occupants.

Fits C-Class · W203 / S203 / CL203 · C-Class · W204 / S204 / C204