Find your next part.

Replacement pull handle for the bonnet release latch. The creator designed it for 123-series cars, printed it successfully, warm-formed the slight original curve and drilled the metal-pin hole after printing. Shape only while warm, retain the original metal pin, verify full latch travel and confirm both primary and safety latches engage before road use. The creator only says it may fit later 124-series cars, so no cross-fitment is assigned.

Fits W123 Series · W123 / S123 / C123

Two-piece holder and mounting bracket for storing a reflective warning triangle on the inside of the boot lid. The creator measured and photographed this custom installation on a 1979 300 SD that was built for the US market and therefore did not originally have the bracket; no other model year, body, market or factory-option fitment is inferred. The demonstrated installation uses four plastic rivets plus a roughly #10-24 by 1.5-inch screw, nut and wingnut. Compare the boot-lid pressing and triangle dimensions before printing, use automotive-interior heat-resistant material, keep hardware clear of wiring and the outer skin, and confirm the triangle is retained without obstructing the lid or latch.

Fits S-Class · W116

Full-size glovebox body measured by hand from an original 107-series part. The creator states that one hole beside the lamp opening is intentionally absent, so transfer and drill that position from the original only after confirming lamp, latch, hinge and dashboard clearances. Use cabin-heat-resistant material and test the box without forcing aged dashboard trim.

Fits SL · R107

Workshop adapter that seals the airflow-meter opening to connect a smoke machine during intake-system leak diagnosis. The creator shows it fitted on a 107-series engine. Use only on a stationary, cool engine with low-pressure diagnostic smoke, protect the airflow meter and hoses from excess pressure, never run or drive the car with the adapter installed, and remove it after testing.

Fits SL · R107

Four-piece printable shell for rebuilding the weathered electrical connector on a 107-series central-locking mechanism cable. The source photographs the failed original, loose terminals, printed assembly and installed connector, and notes that PLA worked for the prototype; PETG, ABS or nylon is preferable for cabin and door-cavity heat. Preserve terminal positions and insulation, disconnect the battery before electrical work, verify polarity and strain relief, and test locking operation before closing the trim.

Fits SL · R107

Cosmetic snap-on cover for an exposed armrest fastener. The source identifies 107-series fitment but gives no production-break or upholstery-colour claim. Use a cabin-heat-resistant material, compare the fastener head and receiving recess, and test gently so the printed clip does not damage aged seat or armrest trim.

Fits SL · R107

Replacement retaining clip for the removable suncover on the 300 SL. The source claims only 300 SL 107-series fitment, so no other engine, trim or model-year application is inferred. Use cabin-heat-resistant material, compare the original clip and mounting interface, and verify secure retention without stressing the cover.

Fits SL · R107

Replacement frame fitted beneath the rubber gear-selector boot to retain it in the centre console. The creator explicitly identifies 107-series SL and SLC fitment and designed it because the original retainer was unavailable. Compare the selector opening and boot lip, use heat-resistant material, and confirm unrestricted selector movement through every position before driving.

Fits SL · R107

Drop-in cup holder designed for the centre-console recess of the creator's 1989 560 SL. It prints without supports and includes a shallow adjacent tray. Fitment is limited to the demonstrated late-production console; compare the recess before printing, keep the holder clear of the selector and handbrake, and verify that containers cannot interfere with any control.

Fits SL · R107

Four-piece conversion set for the early dashboard centre stack: a single-DIN HVAC/radio panel, left and right slider trim, and an ashtray-replacement holder for a USB charger or voltmeter. The creator built and photographed it in an early 450 SL and warns that switch layouts changed over production even though the panel outline may remain similar. Restrict use to the demonstrated early layout, compare every opening and fastener before printing, fuse any added electrical outlet correctly, and retain safe clearance from wiring and HVAC controls.

Fits SL · R107

Replacement retaining clip for the cabin sun visor. The creator made and printed it for an older 107-series SL and notes that print cleanup may be needed. Use a cabin-heat-resistant material, compare the screw spacing and visor-rod interface with the original, clean the retention opening carefully, and confirm that the visor locks and releases without damaging the headliner.

Fits SL · R107

Replacement internal louver for the centre dashboard vent, with a dashboard-location diagram and CAD view. The creator reports using it to restore broken, non-adjustable air diverters. Match the original orientation, use cabin-heat-resistant material and verify smooth adjustment without binding.

Fits Z4 · E85 / E86

Creator-printed protective caps for exposed door and boot lock openings. Only the source-designated 20 mm door cap and 36 mm flat boot cap are retained; four alternate test sizes are excluded. Confirm opening diameter, key access where required, drainage and secure retention.

Fits Z4 · E85 / E86

Left and right headlight-washer nozzle covers, shown as a physical print. The E85/E86 source identity corresponds to the facelift bumper with headlight cleaning system S502A. RealOEM identifies primed left 51117078261 and right 51117078262 from January 2006; confirm production date, bumper, side, paint code and S502A before finishing and fitting.

Fits Z4 · E85 / E86

Small support frame that attaches the painted headlight-washer cover to the washer nozzle, shown physically installed after the creator's one-year ABS test. BMW supplies the frame only with the complete nozzle, so no parent-assembly number is assigned. Verify cover retention, nozzle extension and legal washer operation.

Fits Z4 · E85 / E86

Push-fit single- and double-container holders for the small rear-console recess behind the handbrake. The creator designed and printed them for a 2004 Roadster, including a 473 ml can version. Confirm handbrake, shifter, seat, belt-buckle and roof-control clearance and remove the holder if it can interfere.

Fits Z4 · E85 / E86

Replacement black screw cover for the centre console, shown installed and as loose physical prints. RealOEM and BMWFans identify the compatible separately serviced black plug as 51167906699, produced from April 2005 and used on E85 Roadster and E86 Coupe interiors. Confirm the black trim specification and opening shape before fitting.

Fits Z4 · E85 / E86

Replacement swivelling support arm for a broken dashboard cupholder, shown in the opened installed assembly and beside the original mechanism. Mirror the model for the opposite side. Verify smooth deployment, positive stowage and secure cup support without obstructing the vent or passenger airbag area.

Fits Z4 · E85 / E86

Three-part left/right-mirrored mount set for storing the removable Roadster wind deflector behind the seats, shown installed in four physical views. The design uses four M3 nuts, M3x12 screws, spacers and nut holders. Confirm fastener retention and seat, belt, roof and rear-view clearance.

Fits Z4 · E85 / E86

Trunk-wall relocation mount for the Roadster folding-top hydraulic motor. The creator and beta testers report over a year of successful use when secured with two zip ties; the relevant physical motor-and-mount image and CAD views are retained. Mount upright with the reservoir uppermost, fasten to suitable metal, protect hoses and wiring, and cycle the roof while checking leaks, chafe, clearance and emergency operation.

Fits Z4 · E85 / E86

Four-piece mounting set for a creator-built acrylic Roadster wind deflector, physically shown after printing. It uses M8 fasteners and hooks around the roll hoops. Inspect the acrylic edges and fasteners, use locking hardware, and verify seat, belt, roof, rear-view and emergency-egress clearance before driving.

Fits Z4 · E85 / E86

Two-piece clip for the wheel-housing service flap, shown installed, loose and after extended use. The creator reports that PLA softened but still held after two years and recommends a more heat-resistant material. BMW does not service this clip separately from the surrounding flap, so no parent-assembly number is assigned. Verify closure and tyre, lamp and suspension clearance.

Fits Z4 · E85 / E86

Ashtray-panel replacement for two 52 mm gauges, shown physically installed. Installation requires trimming the original ashtray carrier; confirm gauge depth, wiring, shifter and control clearance, fuse any added electrical circuits and keep all warning lamps and controls visible.

Fits Z4 · E85 / E86

Printed replacement for the four retaining circlips on the Roadster folding-top compartment shelf. The creator reports PETG as strong enough. RealOEM and BMWFans identify the separately serviced circlip as 54317113270, used from September 2002 on E85 Roadsters in LHD and RHD markets. Confirm all four clips retain the shelf without obstructing roof movement.

Fits Z4 · E85 / E86