Find your next part.

Replacement sunvisor clip.

Fits 924 · 924 · 944 · 944

Phone holder designed to fit beside the dashboard display. The author supplies a base holder and phone-specific variants for iPhone 11, iPhone 8 Plus, and the 2016 iPhone SE, and shows a physical holder fitted in the vehicle. The creator used heat-resistant Extrudr GreenTEC rather than ordinary PLA, which can soften in a hot cabin. Choose only the matching variant, confirm secure retention, and keep the device clear of the driver’s view, controls, airbags, and ventilation.

Fits A-Class · W176

Custom adapter frame for the specific 7-inch double-DIN Android head unit linked by the creator. Source photographs show the printed frame and the modified centre-console opening. Confirm the radio dimensions and console cut-out before printing, protect the veneer and wiring, provide adequate ventilation and strain relief, and do not assume other double-DIN units share the same bezel geometry.

Fits 190 Series · W201

Made this few years back. Still intact till today. Drop a comment for feedbacks Printed in ASA 100% fill. ABS or others Enable "Detect Thin Wall" Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Mounting clip replacement for the BMW E46 kidney grill. The kidney grills are held in place in the bonnet through flexible lips, which become brittle with time and heat exposure. My car is 14 years old and the kidney grills had lost their grips a while ago and were about to fall over. The quick fix was to string them up from the inside, but hardly an elegant fix for a BMW! Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Short reinforced replacement lever for the brittle E30 hood-release handle, physically installed with a 4 mm or #8 screw and locknut. Print solid around the pivot and confirm reliable hood release before closing the hood.

Fits 3 Series · E30

Three-piece cup-holder assembly tested in a 2010 BMW E87. It relocates the drink above the original low cup recess so taller containers can be used without the armrest interfering. The retained package contains the adapter, bridge, and cup cradle. Use a heat-resistant cabin material and verify secure engagement before driving.

Fits 1 Series · E81 / E82 / E87 / E88

Flexible replacement dust cover for the automatic shifter gate in 2005–2010 Grand Cherokee WK and WH center consoles. The creator documents the installed fit and specifies NinjaFlex.

Fits Grand Cherokee · WK / WH

Audiocircle Dashboard Speaker Adapter for Toyota 86 / GR86, mapped to the ZN8 generation based on the source fitment information. Source explicitly says 2022 BRZ

Fits 86 / GR86 · 2nd Gen

Tested replacement glovebox handle for the 2013 Toyota RAV4, intended as a functional interim replacement and recommended by the author for a solid print.

Fits RAV4 · 4th Gen

Three ashtray-replacement panel variants for adding rear-seat USB outlets, including switched and mirrored switched layouts.

Fits Land Cruiser · 80 Series · Lexus LX · 450

Loose- and tight-fit holders for fitting a 5 mm 12-volt LED and panel-mount bezel into a 16 mm Jaeger or Smiths gauge opening. The creator notes that the tight version may break during removal and suggests optional hot glue after installing the LED.

Fits Series · 2A · Series · 3

Three-part replacement sun-visor retainer for either side. Print the body flat, the clip prongs upward, and the cap with its tube upward, then glue the clip into the body before installation.

Fits Discovery · 1

Four-part holder for installing a Webasto MultiControl unit in place of the factory ashtray, including base, bracket, front panel, and spring clip.

Fits Discovery · 3

Replacement console cup-holder bodies with flexible retaining stays. Print the main body in PETG and the stays in TPU, then press the stays in from the outside before installation.

Fits Discovery · 3 · Range Rover Sport · L320

Replacement sunroof rail and locking bracket for the P38 electric sliding roof. Related genuine guide assemblies are EXM100360 (RH) and EXM100370 (LH)

Fits Range Rover · P38

Dashboard drinks holder for the Range Rover P38, based on genuine Land Rover accessory LRN32685 with printability changes and an added tray for pens and coins.

Fits Range Rover · P38

This a double fuel pipe clip for Td5 defenders, to hold fuel hoses to the chassis.

Fits Defender · Td5

Full-size upper dashboard panel for the Land Rover Defender Td5 (1998–2005), replacing the upper dashboard top/facia component across the instrument-panel area. Verify VIN and windscreen/vent variant, drive side, demister and fastener interfaces, dimensions, clearances, and material/print strength before installation.

Fits Defender · Td5

If you mount the MRC7354 "Soft Top Front Seat Belt Bar For Land Rover Defender / Series" the tube do not fit very well the the capping. This part gives it a nice an stable connection. Needs tu be drilled trough after mounting fpr a tight fit. Drill 8 mm oder 5/16 "

Fits Defender · 200 Tdi · Defender · 300 Tdi · Series · 2 +2

Spacer for mounting a 165 mm (6.5 inch) aftermarket speaker to the MiTo three-hole door pattern while clearing the window glass and door card. The creator reports perfect rear-door fit; the front mounting holes required slotting. The editable STEP file is archived, while the validated STL is supplied. Verify front/rear hole position before drilling.

Fits MiTo · Tipo 955

Center-console cup-holder insert that supports larger drink containers; the creator strengthened later revisions after long-term use.

Fits Cayenne · E1 (955 / 957)

Phone mount that clips around an 82 mm dashboard gauge and accepts a WizGear magnetic holder.

Fits 911 · 964 · 911 · 993

Left and right replacement door-handle inserts designed to print face-down for a textured finish.

Fits 924 · 924