Find your next part.

Protective cap for the upper front strut bearing on a BMW E36, physically shown printed and installed in the engine bay. Use engine-bay-rated material and confirm it clears the strut brace, nut and suspension movement.

Fits 3 Series · E36

Replacement spacer for the front drink recess in the BMW E36 factory centre-console cupholder, physically shown installed. The creator lists accessory number 82111469119, but it was not independently resolved to this printed subcomponent and is intentionally omitted.

Fits 3 Series · E36

Direct replacement retainer for the BMW E36 Touring tailgate trim, physically shown installed at the lower edge of the open tailgate. Print in a tough material and confirm every stud and clip seats without distorting the trim.

Fits 3 Series · E36

Rear-cap extension physically fitted to an original BMW E36 fog lamp to clear the cooling fan on an LED replacement bulb while retaining the stock cap. Check bulb legality, connector strain, weather sealing, lamp clearance and heat before road use.

Fits 3 Series · E36

50 mm inner-diameter service sleeve for pressing output-flange seals out of the 168 mm differential on a 1995 E36 318ti. The source shows the physical tool and flange. Support the housing correctly, keep the tool square, and do not reuse a damaged seal.

Fits 3 Series · E36

67 mm cupholder and 54 mm reducer for the square opening ahead of the armrest in an E36 Compact. The source shows both sizes physically installed with 250 ml and 500 ml cans. Verify handbrake, shifter and armrest clearance before use.

Fits 3 Series · E36

Replacement holder for the BMW E36 engine-bay inspection lamp, physically printed by the creator. Use ABS, nylon or another engine-bay-rated material, secure the lamp wiring away from heat and moving components, and verify the lamp cannot detach.

Fits 3 Series · E36

Service driver sized to install 168 mm differential output seals to the original depth on four-cylinder E36 and creator-listed Z3 applications. The source shows the physical tool on the differential. Use with a flat striking plate, measure seal depth, and inspect the seal lip before assembly.

Fits 3 Series · E36 · Z3 · E36/7 / E36/8

Replacement tow-eye opening cover for the E36 M-Technic/M3-style rear bumper, physically compared with the original and shown installed. The creator reports a tight fit and optional spring-clip provision. The nearby catalog number identifies the parent trim panel, so no OEM number is assigned.

Fits 3 Series · E36

Multi-part repair set for BMW E36 passenger air-vent knobs, arms, plugs, lever, washer and connectors. The creator physically assembled and installed the revised parts. Select the matching left/right pieces and verify every louvre moves freely without binding.

Fits 3 Series · E36

Left/right parcel-shelf support pin for BMW E36 Compact and E46 Compact, physically installed by the creator. BMWFans confirms the exact right support as 51468146708. Use a tough material and verify shelf engagement without overloading the side trim.

Fits 3 Series · E36 · 3 Series · E46

Grooved replacement hook for the E36 Compact parcel-shelf cord, refined from the original model and physically compared with the stock hook. Print in a tough material and verify the cord releases without cracking the shelf.

Fits 3 Series · E36

Press-fit E36 centre-console storage tray with separate coin and small-item areas, physically shown installed between the seats. Confirm it does not obstruct the handbrake, seat-belt buckles or seat travel.

Fits 3 Series · E36

Small repair cap for a damaged front-door tweeter grille on a BMW E36 325i. The source photo shows the original damage and repaired physical cover. Verify the cap cannot contact the speaker cone or loosen into the door.

Fits 3 Series · E36

Replacement push rivet for the 16 mm rear carpet holes in BMW E36 luggage compartments. The creator shows the finished print installed in carpet. Print in a tough material, test removal on one location, and do not force it into a smaller opening.

Fits 3 Series · E36

Adapter for a standard 100 mm rear ceiling speaker in a 1998 E36 318i Touring. The source physically shows the printed ring, speaker and installed assembly. Confirm cone, magnet, wiring and headliner clearance before fastening.

Fits 3 Series · E36

14 mm hex-drive hand tool for the star-shaped cell caps on the original battery in a 1999 E36. The source shows both the printed wrench and matching battery caps. Use only with the battery isolated, wear eye protection, and do not short the terminals.

Fits 3 Series · E36

Three-gauge panel for the E36 sunglasses cubby, physically installed after widening the side clips by 2 mm. The uploaded orientation is for RHD; the creator directs LHD cars to mirror the model. Cutting the original cubby is required, so dry-fit the panel and preserve OBC and switch clearance.

Fits 3 Series · E36

Left and right adapters for installing standard 5.25-inch rear speakers in the BMW E36 318ti Compact without cutting the original housings. The source shows the printed adapters, speaker assembly and installed housings. Verify speaker depth, wiring clearance and screw retention.

Fits 3 Series · E36

Two-piece conversion for the factory 1992–1999 E36 cupholder module, flattening and widening the support for modern cans and cups. The creator used the installed insert and documents 318i, 325i, 328i and M3 fitment. Use cabin-heat-resistant material and confirm the module still clips securely.

Fits 3 Series · E36

Replacement release handle for E30 Touring luggage-compartment side covers, physically installed and reported working with the original bent linkage rods. Verify both latches release and re-engage.

Fits 3 Series · E30

Screw-on protective cover for exposed E30 front wheel-bearing spindle surfaces during restoration, washing, blasting, painting or storage. It is physically shown on the spindle and is removed before wheel-bearing assembly.

Fits 3 Series · E30

Replacement clip retaining the bulb holder in early E30 taillights, printed in PETG and physically installed. Late-light fitment is unconfirmed. The creator-listed 63211376879 resolves to an unrelated rotary knob in BMWFans, so it is intentionally omitted.

Fits 3 Series · E30

Replacement latch striker for E30 Touring luggage-compartment side covers, reproduced from the original and physically shown working. BMWFans confirms latch striker 51471947370.

Fits 3 Series · E30