Every printable part.

Replacement front-strut top dust cover for E30 cars fitted with Koni adjustable dampers where the stock cover does not fit. The creator printed and used the PETG version; confirm adjuster clearance and cap retention.

Fits 3 Series · E30

Two replacement plastic pieces for the late-model E30 headlamp adjusting screw, copied from the originals and shown assembled on the screw. BMWFans confirms adjusting screw 63121385397. Form threads carefully and verify beam adjustment and retention.

Fits 3 Series · E30

Replacement E30 luggage-compartment clip for the factory wheel wrench, designed for the original mounting hole and physically shown retaining the wrench. BMWFans confirms clamp 51471933468.

Fits 3 Series · E30

Reinforced replacement lower wiring cover for E30 door mirrors, copied from the original and physically fitted. The supplied geometry is LHD; mirror it for RHD. BMWFans confirms left/right LHD 51161937441/442 and RHD 51161937443/444.

Fits 3 Series · E30

Replacement E30 front-strut wiring holder copied from the original and physically installed. BMWFans confirms cable holder 61131370421. Use heat- and abrasion-resistant material and verify wire clearance through full steering travel.

Fits 3 Series · E30

Replacement gear set for BMW E30 VDO odometers, physically shown in the cluster. The common small gear duplicated by the MotoMeter source was removed from this submission during global hash preflight.

Fits 3 Series · E30

Replacement gear set for BMW E30 MotoMeter odometers, shown against and installed in a physical cluster. Gear numbers in the source are creator labels, not BMW component numbers.

Fits 3 Series · E30

Replacement high-beam headlamp spacer for both Hella and Bosch E30 lamp frames, reproduced from the original and physically fitted. BMWFans confirms intermediate piece 63121362036.

Fits 3 Series · E30

Replacement E30 ignition-lock trim ring reproduced from a broken original and shown fitted. BMWFans identifies ring 32311162057. Confirm steering-column trim version and do not obstruct key or lock-cylinder movement.

Fits 3 Series · E30

Replacement headliner bracket supporting the dome light in an E30 coupe, physically compared with a failed original and installed. It is not claimed for convertible bodies; sedan fitment was not independently established. BMWFans confirms bracket 54121884483.

Fits 3 Series · E30

Reinforced fastening repair for the E30 centre-side or B-pillar trim cover, copied from the original attachment and intended to be bonded to the broken cover. The creator-listed 51431933731/732 references are parent trim covers, so no OEM number is assigned.

Fits 3 Series · E30

Straight and 90-degree reusable molds for rebuilding disintegrated overmolded BMW E3x electrical terminals with hot glue or a suitable insulating compound. The source includes a repair write-up; preserve terminal alignment and verify insulation and water resistance before connection.

Fits 3 Series · E30

Inner and outer replacement covers for E30 headrest-post openings. The creator reports they function, though less precisely than the originals. BMWFans identifies the matching inner and outer covers as 52101838969 and 52108191245; verify position before fitting.

Fits 3 Series · E30

Replacement trim cover for exposed E30 seat-rail and seat-belt anchorage nuts. Match the installed fastener size and ensure the cover does not interfere with seat travel or belt hardware.

Fits 3 Series · E30

Four-part replacement centre-cap system for 15-inch BBS RZ Style 5 wheels used on E30. The creator prototyped and fitted it, documents assembly and temperature-resistant materials, and advises checking the printed nut position regularly. The separate 68 mm badge number is intentionally omitted.

Fits 3 Series · E30

Replacement bushing for the E30 wiper-arm pivot on the passenger side of LHD cars or driver side of RHD cars. It is dimensioned for the standard M22×5.5 nut and physically fitted; BMWFans identifies 61611370387 as the corresponding covering cap.

Fits 3 Series · E30

Two-piece replacement cover and holder for securing the spare wheel in the E30 luggage compartment, shown physically installed. Confirm thread engagement and wheel retention before driving.

Fits 3 Series · E30

Replacement electrical connector housing for the classic Alpina vent gauge, designed around BMW 2.8 mm crimp terminals and compared with the original connector. Match terminal locking and pin order to the vehicle wiring before energizing.

Fits 3 Series · E30

Printed cap wrench for the 76 mm, 14-flute oil-filter housing associated with BMW 11421715960. The creator physically demonstrates the tool and lists E30, E36, E46, E34 and Z3 applications; confirm cap size before applying torque.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46 +2

Replacement clip for retaining the E30 sunroof cables. The creator reports two years of use without an issue and recommends PETG. Verify cable capture and unrestricted sunroof travel after installation.

Fits 3 Series · E30

Replacement cap physically shown on the windshield-washer reservoir of a BMW E30 320i with M20 engine. Use washer-fluid-resistant, heat-tolerant material and confirm a snug seal without forcing the reservoir neck.

Fits 3 Series · E30

Dust cap for replacement-style E30 front strut mounts with an approximately 31.3–32 mm opening, where the original cap no longer fits. Test-print the retaining ring and adjust scale for the measured mount before making the full cap.

Fits 3 Series · E30

Spinning replacement knob and glue-in collar made for the manual sunroof crank of a 1985 BMW E30. The creator shows the finished print on the crank. Dry-fit and keep adhesive away from the rotating shaft; no other year or chassis is claimed.

Fits 3 Series · E30

Press-on replacement cover for the original BMW E21 fuse box. The creator physically installed the ASA print and notes that the 220 mm model can be split and solvent-welded for smaller printers. Verify clearance, electrical isolation, heat resistance and secure retention.

Fits 3 Series · E21