Every printable part.

Two replacement retaining clips that keep the estate rear seatbelts clear while the seat backs are folded. The creator reports accurate fit and warns that PLA deformed in summer cabin heat; use PETG or a more heat-resistant material.

Fits E-Class · W211 / S211

Left and right plastic recesses that retain the metal mounting points for the estate luggage-compartment protection-net roller on the rear-seat backs. The creator reports a snug fit, recommends PETG with build-plate supports, and notes that the 9 mm bracket holes are intentionally tight.

Fits E-Class · W211 / S211

Replacement pull clip for the factory rear side-window sunshade. The creator modeled it from the factory design, reports direct fit without modification, and recommends ABS or PETG with 0.2 mm layers and 100% infill for cabin heat resistance.

Fits E-Class · W211 / S211

Storage tray that installs in place of the factory CD changer. The creator specifies ASA or ABS, four walls, five top and bottom layers, and 13% infill.

Fits E-Class · W211 / S211

Four-piece concealed storage compartment installed in place of the factory CD changer and opened with the button below the radio. The source states automatic closing after 30 seconds; wiring and actuator details remain the installer’s responsibility.

Fits E-Class · W211 / S211

Replacement cap for the roof-trim opening. The source includes the printed cap and installed physical views; confirm the opening dimensions and trim variant before installation.

Fits E-Class · W211 / S211

Replacement rear-bumper support bracket corresponding to the exact child number identified by the creator. Print upright with high infill in ABS or polycarbonate-class material, use support only at the latch, and remove the modeled sacrificial support from the screw hole after printing.

Fits E-Class · W211 / S211

Replacement link for the folding center-console cup-holder mechanism. Source photos document the original mechanism, printed part and working assembly; verify smooth movement before reinstalling the trim.

Fits E-Class · W211 / S211

Left and right rosettes for the luggage-compartment side panels around the boot-lid hinge arms. The author reports a perfect fit but instructs users to make a small cut after printing so each rosette can be installed around its arm. Molded child numbers were not independently verified, so no OEM number is assigned.

Fits E-Class · W211 / S211

Exterior rear-window cover for the estate body, replacing the corroded metal cover around the rear-wiper shaft. Bond with automotive glass adhesive or sealing silicone and retain the source-stated estate-only fitment.

Fits E-Class · W211 / S211

Replacement opening handle for the storage compartment below either front seat. Print vertically with support beneath the hinge features and verify hinge movement before loading the compartment.

Fits E-Class · W211 / S211

Three-piece installation frame for a nine-inch Android head unit. The author describes it as functional but imperfect and requiring finishing; join all three parts as shown by the source and check secure retention before driving.

Fits E-Class · W211 / S211

Replacement for the break-prone plastic part inside the center armrest, with holes for the factory screws. Verify screw seating and free hinge movement before use.

Fits E-Class · W211 / S211

Replacement tab for the rear center-console air vent. The author states that it fits this vent position only and that other air-vent locations were not tested; surface finishing and paint may be needed.

Fits E-Class · W211 / S211

Replacement connector gear for the factory CD changer opening arm. The source documents the failed original and the printed replacement; confirm tooth engagement before closing the changer mechanism.

Fits E-Class · W211 / S211

Flexible insert for the damper on the estate luggage-compartment floor. The creator reports that it seats well and works; use flexible TPU and verify the damper-end dimensions before installation.

Fits E-Class · W211 / S211

Replacement clip for the footwell storage net. The source provides a physical installed-net image and a printed sample; no other model or side is inferred.

Fits E-Class · W211 / S211

Straight and bent replacement variants for the left rear bumper retaining clip. Fitment is limited to the creator-stated chassis and side; no opposite-side or facelift applicability is inferred.

Fits E-Class · W211 / S211

Two-part landscape phone mount for the center vent. The author tested the printed ABS part on an Avantgarde right-hand-drive car, warns that vent and trim variants may differ, and advises against PLA because of cabin heat. Removal may require gently opening the vent vane with a spudger.

Fits E-Class · W211 / S211

Cup holder that clips to the right side of the center console through the open cigarette-lighter door. The author designed it for 2003–2008 vehicles and recommends printing the version 3 upside-down STL as one piece; the parametric and split alternatives are retained.

Fits E-Class · W211 / S211

Replacement retaining clip for the luggage-compartment upholstery. The creator identifies the application as the CLK 209 series and describes the model specifically as a trunk-upholstery clip. No side, body-style, market, steering-side, engine, facelift, trim or option-code extension is claimed beyond the source-backed C209/A209 generation.

Fits CLK · C209 / A209

Two-piece phone holder and charging-cable bracket for the CLK 209 series, source-tagged by the creator for W209. The holder clips between the center-console side wall and the climate-control panel, accepts an iPhone 6, 7 or 8, and locates a Baseus charging cable so the phone charges when inserted. The creator explicitly warns against ordinary PLA because it can melt in a hot cabin. Fitment is not extended beyond C209/A209.

Fits CLK · C209 / A209

Replacement rear registration-plate lamp lens for the CLK 209 series. The creator supplies two verified author models: one version retains legs for the festoon bulb and one omits those legs. Print in clear filament; the creator recommends PETG rather than PLA for improved heat and weather resistance, a 0.2 mm translucent window, and silicone sealant around the rim to prevent water ingress. Fitment is source-backed only for the C209/A209 generation.

Fits CLK · C209 / A209

Replacement folding-roof flap and repair-hinge geometry for a broken small roof flap. The creator designed new hinges that attach to the retained original corner piece because the flap was not separately available, and provides three author STLs plus physical source photographs. Exact model-year, side, facelift and roof-option splits are not stated. Compare the original flap, corner piece and hinge clearances before printing; use UV-, weather- and cabin-heat-resistant tough material, deburr every edge, and cycle the folding roof stationary through its full travel while checking that the flap closes, latches and clears seals and adjacent panels. Stop use if any part binds, cracks or loosens; this repair does not replace the roof lock, hydraulic drive or structural linkage.

Fits SL · R230