Every printable part.

Workshop tool for seating the oil seal in an LT230 transfer box. The creator printed it in PETG with a 2 mm shell and 50% infill.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Dashboard mounting bracket for a Garmin navigation unit in the Puma interior.

Fits Defender · Puma

Workshop fitting tool for seating the rear hub seal squarely.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +3

Two fit variants of a blanking plate for the 1998 dashboard ashtray opening.

Fits Defender · 300 Tdi · Defender · Td5

Replacement windscreen-washer reservoir cap with retaining-ring eyelet, spill-reducing internal lips, and a 0.4 mm vent hole.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Two headlining fastener sizes for a 110.

Fits Defender · Td5

Air-intake vent that replaces the removable seat-box floor grommet when fitting a diesel night heater. The creator secured it with marine sealant.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Adaptor to fit Discovery 2 Cruise Control switch to Defender td5. Quote from SimonRafferty: "It's very easy to add cruise control to any Td5 Land Rover Defender just by adding a couple of wires to the ECU and connecting them to a switch. (search on line for details) Unfortunately, there are no nice looking switches. My solution was to fit a switch from a Td5 Discovery 2 - and print this adaptor so it can easily screw on to the steering column. This is version 2 which is a much better fit and prints in one piece. Use higher temperature filament such as PETG or PAHT - otherwise it will melt in the sun. That's how come V2 came to be! Insert a couple of M4 Nuts into the slots provided, then attach the switch with 2 x M4 x 10mm screws"

Fits Defender · Td5

Replacement speaker-grille cover for the 1998 50th Edition, supplied as one complete piece or two halves for smaller printers.

Fits Defender · 300 Tdi

Front bumper end cap clip for Defender

Fits Defender · Puma

Clip to hold brake pipes to chassis for Defender TD5. It fits into existing 7mmØ holes in chassis and holds a 5mmØ brake pipe secured by a 4.7mm*1.3mm nylon cable tie. It's designed to be forced into the chassis with a hammer and strongly hold the brake pipe even without beeing secured by the cable tie, but be aware that brake pipes are quite sensible parts of a vehicle and may result to your death if not secured appropriately. Use this part at your own risk and check conditions of the brake pipe clip regularly.

Fits Defender · Td5

52mm hub nut socket for a wide range of Land Rover models. Most wheel bearings only need gentle torque - a few later models use the same nut but with huge torque and this likely won't work for those. 1/2" socket plus a 27mm (wheel nut) sized hex on the back. Designed to be printed without supports. Print in something robust.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Discovery · 1 +5

Trim Clip for Fuse Box Cover on Defender from 2007 Onwards

Fits Defender · Puma

Printable male connector bodies and mounting parts for the original dashboard E-switch and hazard-switch positions.

Fits Defender · Td5

Replacement flange for repairing or upgrading the Td5 air-filter housing connection.

Fits Defender · Td5

Console for mounting auxiliary switches or other equipment in the small driver-side dashboard recess. Blank and pre-drilled versions are included for both left- and right-hand-drive vehicles

Fits Defender · L663

Base-plate adapter for fitting GMC/Chevrolet pickup tie-down anchors to the cargo-area ceiling. Installation uses two 3/8 × 1.5-inch carriage bolts with washers and nuts.

Fits Defender · L663

This a double fuel pipe clip for Td5 defenders, to hold fuel hoses to the chassis.

Fits Defender · Td5

Workshop tool for installing the front crankshaft seal on 2.2- and 2.4-litre Puma engines.

Fits Defender · Puma

Bracket for mounting a 2016 Elinz FHD dashcam at the passenger sun-visor fixing point, reusing the original visor screw.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Cubby-box dock for a cased Samsung Galaxy S5 and a cylindrical Qi charging puck.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Two replacements for the unused 1998 centre-panel opening: a plain plug and a post-mounted version for a small air freshener.

Fits Defender · 300 Tdi · Defender · Td5

Three-piece adaptor set for fitting a 1995 Ford F-150 throttle-position sensor to a 1994 3.9-litre V8 throttle body. The creator specifies PETG for engine-bay heat resistance.

Fits Defender · 300 Tdi

Replacement interior end cap for the roof reinforcement bar.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1