Every printable part.

Angled roof-console pod for two 52 mm gauges. Installation requires trimming part of the original mating flange and securing the pod with small countersunk screws.

Fits Discovery · 1

Replacement blanking button for an unused dashboard switch position. Two model variants are included

Fits Discovery · 1

Three-part replacement sun-visor retainer for either side. Print the body flat, the clip prongs upward, and the cap with its tube upward, then glue the clip into the body before installation.

Fits Discovery · 1

Multi-part dashboard tray replacement with interchangeable faces for USB, a brake-controller dial, or three Carling-style switches. Glue the selected face to the tray after test-fitting.

Fits Discovery · 1

Two-part centre-console cup holder with an enlarged approximately 75 mm internal diameter and no phone pocket. Designed from a related holder and explicitly stated to fit this generation.

Fits Discovery · 1

Dashboard surround for fitting a protruding double-DIN navigation head unit without cutting the original dash trim. PETG is recommended because PLA can deform in a hot cabin.

Fits Discovery · 1

Replacement for the rear ashtray that accepts a standard cigarette-lighter or USB power socket. Use a cabin-temperature-resistant material and verify socket dimensions.

Fits Discovery · 1

Bolt-on repair pieces for parcel-shelf eyelets that have torn through. Requires trimming the shelf and two M3 x 7 mm fasteners

Fits Discovery · 1

Replacement left-hand cover for the power-seat switches on a 1996 vehicle. The ribbed design differs slightly from the original

Fits Discovery · 1

Reinforced replacement bracket for a broken rear parcel shelf. Compare side and mounting geometry with the original before printing.

Fits Discovery · 1

Replacement cover for the window-switch panel on three-door vehicles. Confirm switch layout and panel dimensions before printing.

Fits Discovery · 1

Replacement push-fit stud used between the passenger and rear door cards and the plastic receivers in the door structure. Multiple clips are used per panel

Fits Discovery · 1

Insert for the centre-console cubby refrigerator in a 2007 Discovery 3, designed to keep drink cans from rolling and vibrating while driving. Use a cabin-temperature-resistant material.

Fits Discovery · 3

Two-part eyelet mount that clamps around a factory roof rail using common M8 hardware. The source recommends PETG, 20% infill, doubled infill lines, and three walls. Use only for light-duty restraint and never as a rated recovery or lifting point.

Fits Discovery · 3 · Discovery · 4

Replacement quarter-turn screw for retaining the rear-bumper towbar access door when the towbar is not fitted. Print with high infill and confirm engagement before road use.

Fits Discovery · 3

Replacement toggle that retains the rear towing-connection flap. Print at 100% infill

Fits Discovery · 3

Replacement adjuster for the rear seat. Includes the original version and a revised version that prints without supports

Fits Discovery · 3

Replacement centre cap for a Discovery 3 alloy wheel. Confirm wheel and bore dimensions against the original before printing.

Fits Discovery · 3

Holder that keeps a second-row seat-belt buckle upright so children can buckle themselves more easily. Designed around the Discovery mid-row seat geometry.

Fits Discovery · 3 · Discovery · 4

Removable Garmin Nuvi mount sized to sit over the factory navigation display. A raised upper lip locates it in the recess

Fits Discovery · 3 · Range Rover Sport · L320

Shield that prevents the inner rear parking sensors from detecting a raised aftermarket tow hitch. Print two in ASA or another UV- and heat-resistant material.

Fits Discovery · 3 · Discovery · 4 · Range Rover Sport · L320

Dashboard auxiliary-power panel supplied as a single-piece model, with the source also describing a two-piece option for smaller print beds. Confirm socket and switch dimensions before assembly.

Fits Discovery · 3

Replacement trim plug covering the rear-wiper-arm retaining nut. PETG is recommended for sun and heat resistance

Fits Discovery · 3

Four-part holder for installing a Webasto MultiControl unit in place of the factory ashtray, including base, bracket, front panel, and spring clip.

Fits Discovery · 3