Every printable part.

Drop-in organizer for the small console recess ahead of the automatic shifter in a 2010 Wrangler JK or JKU. It provides coin slots and a cylindrical holder.

Fits Wrangler · JK

One-piece rigid replacement for a torn Wrangler JK front-door mesh pocket. Mirror the model in the slicer for the opposite door.

Fits Wrangler · JK

Extender that restores contact between the Wrangler JK tailgate bump stop and a spare tire after fitting offset aftermarket wheels. It accepts the original bump stop and an added rubber isolator.

Fits Wrangler · JK

Bushing spacer developed on a 2008 Wrangler JK to secure a loose front inner-fender splash guard after custom fenders were fitted.

Fits Wrangler · JK

Thin snap-on protector for Wrangler JK door hinges that shields painted hinge faces from gravel impacts. This entry uses the creator's latest bulged-fit revision.

Fits Wrangler · JK

Replacement clip that secures the interior door-handle release cable on Wrangler JK doors. The creator recommends a heat-resistant, slightly flexible material.

Fits Wrangler · JK

Reinforced 24 mm socket for the Pentastar oil-filter housing used in Wrangler JK models. This V2 geometry accepts either a 3/8-inch or 1/2-inch drive; the creator tested the earlier PLA version to the 25 N·m service torque.

Fits Wrangler · JK

Hand wrench for loosening and tightening Wrangler JK Freedom-panel knobs without straining fingers. Two grip profiles are included.

Fits Wrangler · JK

A-pillar mounting post for a RAM-style arm in a Wrangler JK. The design installs with a 5/16-inch by 90 mm socket-head cap screw.

Fits Wrangler · JK

Protective cover for the exposed front vacuum pump on a 2016 Wrangler JK after installation of an open aftermarket bumper. Check bumper clearance before use.

Fits Wrangler · JK

Auxiliary round-rocker switch panel shaped to the curved radio bezel used on 2011–2018 Wrangler JK and JKU interiors. Installation requires holes behind the panel.

Fits Wrangler · JK

Replacement carpet retaining clip for the Wrangler JK. The creator identifies six locations under the dash and seats where this printed fastener replaces a missing clip.

Fits Wrangler · JK

Clip-in defrost-air diverter for 2007–2010 Wrangler JK dashboards. It redirects air from the short factory grille toward the outer windshield edges.

Fits Wrangler · JK

Complete repair set for the missing or cracked center and side vents in a 2002 TJ, including housings, vanes, sliders and geared control pieces. The creator printed prototypes and specifies heat-resistant material for service use.

Fits Wrangler · TJ

Replacement holder for a 5/16-inch square hardtop mounting nut, modeled from the retainers found in the creator's TJ.

Fits Wrangler · TJ

Clamp-style repair for a broken early-TJ temperature-control cable end, modeled and installed on a 1997 Wrangler.

Fits Wrangler · TJ

Paired adapter nuts that allow Mercedes-pattern door-jamb switches to replace the TJ switches on both sides.

Fits Wrangler · TJ

Straight replacement connector for the failure-prone flip-back hinge in the Rugged Ridge TJ soft-top frame. The non-hinged design fits inside the original tubes.

Fits Wrangler · TJ

Replacement treble and bass adjustment button for the stock TJ radio.

Fits Wrangler · TJ

Tested replacement fan-control knob for the 2004 Wrangler TJ, designed to reuse the metal insert from the broken original.

Fits Wrangler · TJ

Replacement internal divider that prevents red and white light bleed inside the TJ taillight after the original metal separator rusts away.

Fits Wrangler · TJ

Two-piece replacement visor clip with a push latch: lift the latch to release the visor and press it down to lock the visor in place.

Fits Wrangler · TJ

Flexible replacement tether sized for the stock 1997–2006 TJ fuel cap, with a split ring that allows installation without removing the cap.

Fits Wrangler · TJ

Drop-in organizer tray for the upper center console of a 1997 TJ, designed to print without supports and test-fitted by the creator.

Fits Wrangler · TJ